The Shenzhen Jushuo Electronics Co., Ltd. AFC07-S**ECA-00 is a 0.5mm pitch FPC/FFC connector with a locking mechanism, designed for upper connection applications. This series is suitable for flexible flat cable connections and is available in both tube (small batch) and reel (bulk order) packaging. It operates within a temperature range of -45 to +85 and is rated for a maximum voltage of 50V and a maximum current of 0.5A.
| Item | Specification | Condition/Test Method |
|---|---|---|
| Ratings | ||
| Rated Voltage (MAX) | 50V | |
| Rated Current (MAX) | 0.5A | AC/DC (Virtual value) 50Hz |
| Ambient Temperature Range | -45 +85 | |
| Electrical Performance | ||
| Contact Resistance | 20 m MAX | Mate applicable FPC/FFC, measured by dry circuit, 20mV MAX, 10mA |
| Insulation Resistance | 500 M MIN | Mate applicable FPC/FFC, apply 500V DC between adjacent terminals or ground |
| Dielectric Strength | No Breakdown | Mate applicable FPC/FFC, apply 200V AC (virtual value) for 1 minute between adjacent terminals or ground |
| Mechanical Performance | ||
| Locking Force | 1.96*n (N) MAX | Insert and extract applicable FFC (0.3mm thick) at 253mm/min |
| Withdrawal Force | 0.49*n (N) MIN | Insert and extract applicable FFC (0.3mm thick) at 253mm/min |
| Terminal/Housing Retention Force | 3.92N MIN | Pull the terminal at 253mm/min |
| Environmental and Other Performance | ||
| Repeated Insertion and Withdrawal | Contact Resistance: 60 m MAX | Actuator up to 20 cycles at < 10 cycles/min (no power) |
| Temperature Rise | 30 MAX | Carrying rated current load (UL 498) |
| Vibration | Discontinuity: 1 ms MAX; Appearance: No Damage; Contact Resistance: 60 m MAX | DC 1mA under power; Amplitude: 1.5mm P-P; Frequency: 10-55-10Hz/min; Duration: 2 hours in each X, Y, Z axes |
| Shock | Discontinuity: 1 ms MAX; Appearance: No Damage | DC 1mA under power; 490m/s {50G}, 3 strokes in each X, Y, Z axes |
| Heat Resistance | Contact Resistance: 60 m MAX; Appearance: No Damage | Mate FPC/FFC, place in 852 air for 96 hours, then return to room temp for 1-2 hours |
| Cold Resistance | Contact Resistance: 60 m MAX; Appearance: No Damage | Mate FPC/FFC, place in -402 air for 96 hours, then return to room temp for 1-2 hours |
| Humidity | Insulation Resistance: 20 M MIN; Contact Resistance: 60 m MAX; Appearance: No Damage | Temperature: 402, RH: 90-95%, Duration: 96 hours, measure within 0.5 hours after returning to room temp |
| Temperature Cycling | Contact Resistance: 60 m MAX; Appearance: No Damage, Corrosion | 5 cycles of: 30 min at -452, 10-15 min at room temp, 30 min at 852, 10-15 min at room temp |
| Salt Spray | Contact Resistance: 60 m MAX; Appearance: No Damage, Corrosion | 484 hours exposure to salt spray (51% solution) at 352, followed by washing and drying |
| SO2 Gas Resistance | Contact Resistance: 60 m MAX; Appearance: No Damage | 24 hours exposure to 505ppm SO2 gas at 402 |
| NH3 Gas Resistance | Contact Resistance: 60 m MAX; Appearance: No Damage | 40 minutes exposure to NH3 gas from 28% Ammonia solution |
| Solderability | Solder Wetting: 95% coverage | Terminal tip dipped in 2355 tin bath for 20.5 sec (0.2mm from tip) |
| Resistance to Soldering Heat | Appearance: No Damage, Deformation | Terminal tip dipped in 2605 tin bath for 50.5 sec (0.2mm from tip) |
| Dielectric Strength | Must meet 4.1.3 | |
Note: 'n' in locking and withdrawal force refers to the number of positions.
