This product is a connector designed for applications requiring reliable electrical connections. It supports a wide operating temperature range and specific humidity conditions, making it suitable for various industrial and electronic environments. The design prioritizes durability and consistent performance under mechanical stress and environmental challenges.
| Item | Test Method | Requirements | QT | AT |
|---|---|---|---|---|
| APPLICABLE STANDARD OPERATING TEMPERATURE RANGE | -40⁰C TO 105⁰C | |||
| STORAGE TEMPERATURE RANGE | -10 ⁰C TO 50 ⁰C (PACKED CONDITION) | |||
| RATING VOLTAGE | 50 V AC / DC | |||
| OPERATING OR STORAGE HUMIDITY RANGE | RELATIVE HUMIDITY | 90 % MAX (NOT DEWED) | ||
| CURRENT | 0.5 A | |||
| APPLICABLE CABLE | t=0.3±0.05mm, GOLD PLATING (GND PLATE: t=0.5±0.05mm, TIN PLATING) | |||
| CONSTRUCTION GENERAL EXAMINATION | VISUALLY AND BY MEASURING INSTRUMENT. ACCORDING TO DRAWING. | ✓ | ✓ | |
| MARKING | CONFIRMED VISUALLY. | ✓ | ||
| VOLTAGE PROOF | 150 V AC FOR 1 min. NO FLASHOVER OR BREAKDOWN. | ✓ | ✓ | |
| INSULATION RESISTANCE | 100 V DC. | 500 MΩ MIN. | ✓ | ✓ |
| CONTACT RESISTANCE | AC 20 mV MAX ( 1 KHz ) , 1 mA . | 100 mΩ MAX. INCLUDING FFC BULK RESISTANCE (L=8mm) | ✓ | ✓ |
| VIBRATION | FREQUENCY 10 TO 55 Hz, HALF AMPLITUDE 0.75 mm, FOR 10 CYCLES IN 3 AXIAL DIRECTIONS. | NO ELECTRICAL DISCONTINUITY OF 1 µs. CONTACT RESISTANCE: 100 mΩ MAX. NO DAMAGE, CRACK AND LOOSENESS OF PARTS. | ✓ | |
| SHOCK | 981 m/s2 , DURATION OF PULSE 6 ms AT 3 TIMES IN 3 BOTH AXIAL DIRECTIONS. | ✓ | ||
| MECHANICAL OPERATION | 20 TIMES INSERTIONS AND EXTRACTIONS. | CONTACT RESISTANCE: 100 mΩ MAX. NO DAMAGE, CRACK AND LOOSENESS OF PARTS. | ✓ | |
| FFC RETENTION FORCE | MEASURED BY APPLICABLE FPC. (THICKNESS OF FFC SHALL BE t=0.30mm AT INITIAL CONDITION.) DIRECTION OF INSERTION: | 0.3N×n MIN. | ✓ | |
| RAPID CHANGE OF TEMPERATURE | TEMPERATURE-40⁰→+15TO+35⁰→+105⁰→+15TO+35⁰C TIME 30→ 2 TO 3 → 30 → 2 TO 3 min UNDER 5 CYCLES. | CONTACT RESISTANCE: 100 mΩ MAX. INSULATION RESISTANCE: 50 MΩ MIN. NO DAMAGE, CRACK AND LOOSENESS OF PARTS. | ✓ | |
| DAMP HEAT (STEADY STATE) | EXPOSED AT 40±2⁰C, RELATIVE HUMIDITY 90 TO 95 %, 96 h. | ✓ | ||
| DAMP HEAT, CYCLIC | EXPOSED AT -10 TO +65 ⁰C, RELATIVE HUMIDITY 90 TO 96 %, 10 CYCLES,TOTAL 240 h. | CONTACT RESISTANCE: 100 mΩ MAX. INSULATION RESISTANCE: 1 MΩ MIN. (AT HIGH HUMIDITY) INSULATION RESISTANCE: 50 MΩ MIN. (AT DRY) NO DAMAGE, CRACK AND LOOSENESS OF PARTS. | ✓ | |
| DRY HEAT | EXPOSED AT 105±2 ⁰C, 96 h. | CONTACT RESISTANCE: 100 mΩ MAX. NO DAMAGE, CRACK AND LOOSENESS OF PARTS. | ✓ | |
| COLD | EXPOSED AT -40±3⁰C, 96 h. | ✓ | ||
| SALT MIST | EXPOSED AT 35±2⁰C , 5 % SALT WATER SPRAY FOR 96 h. | CONTACT RESISTANCE: 100 mΩ MAX. NO EVIDENCE OF CORROSION WHICH AFFECTS TO OPERATION OF CONNECTOR. NO DAMAGE, CRACK AND LOOSENESS OF PARTS. | ✓ | |
| SOLDERABILITY | SOLDERED AT SOLDER TEMPERATURE, 245±5 ⁰C FOR IMMERSION DURATION, 2±0.5 sec. | A NEW UNIFORM COATING OF SOLDER SHALL COVER A MINIMUM OF 95 % OF THE SURFACE BEING IMMERSED. | ✓ | |
| RESISTANCE TO SOLDERING HEAT | 1) REFLOW SOLDERING PEAK TMP. 250 ⁰C MAX . REFLOW TMP. OVER 230 ⁰C WITHIN 60 sec. 2) SOLDERING IRONS : TMP. 350±10⁰C FOR 5±1 sec . | NO DEFORMATION OF CASE OF EXCESSIVE LOOSENESS OF THE TERMINALS. | ✓ |
