Function: This specification covers the 0.3mm Pitch FPC/FFC Connectors.
Usage: Used for connecting FPC/FFC cables.
Application Scenarios: Applicable to 0.3mm pitch flexible flat cable connectors.
| Item | Specification | Requirement |
|---|---|---|
| Rated Voltage (MAX) | 30V [AC/DC(Virtual value)50Hz] | |
| Rated Current (MAX) | 0.2A | |
| Ambient temperature Range | -25~ +85 |
| Item | Test Condition | Requirement |
|---|---|---|
| Electrical Performance: Contact Resistance | Mate applicable FPC/FFC and measure by dry circuit, 20mV MAX, 10mA. | 20 m MAX |
| Electrical Performance: Insulation Resistance | Mate applicable FPC/FFC and apply 500V DC between adjacent terminal or ground. | 500 M MIN |
| Electrical Performance: Dielectric Strength | Mate applicable FPC/FFC and apply 200V AC (virtual value) for 1 minute between adjacent terminal or ground. | No Breakdown |
| Mechanical Performance: Locking and Withdrawal Force | Insert and extract applicable FFC at the speed rate of 253mm/minute. | Locking: 1.96*n (N) MAX Withdrawal: 0.49*n (N) MIN |
| Mechanical Performance: Terminal /Housing Retention Force | Pull the terminal at the speed rate of 25 3mm per minute | 3.92N MIN |
| Environmental Performance: Repeated Insertion and Withdrawal | Insertion and withdrawal actuator up to 20 cycles at the speed rate of less than 10 cycles/minute | Contact Resistance: 60 m MAX |
| Environmental Performance: Temperature Rise | Carrying rated current load. (UL 498) | Temperature Rise: 30 MAX |
| Environmental Performance: Vibration | DC 1mA energized state; vibration along X, Y, Z axes; amplitude 1.5mm; sweep time 10-55-10Hz/min; duration 2 hours. | Appearance: No Damage Contact Resistance: 60 m MAX Discontinuity: 1 ms MAX |
| Environmental Performance: Shock | DC 1mA energized state; 6 directions perpendicular to the mating axis; 490m/s {50G} shock; 3 times each. | Appearance: No Damage Discontinuity: 1 ms MAX |
| Environmental Performance: Heat Resistance | Mate applicable FPC/FFC; place in 852 air for 96 hours; then return to room temperature for 1-2 hours. | Appearance: No Damage Contact Resistance: 60 m MAX |
| Environmental Performance: Cold Resistance | Mate applicable FPC/FFC; place in -402 air for 96 hours; then return to room temperature for 1-2 hours. | Appearance: No Damage Contact Resistance: 60 m MAX |
| Environmental Performance: Humidity | Mate applicable FPC/FFC; place in 402, 90-95% RH air for 96 hours; measure within 0.5 hours after returning to room temperature. | Appearance: No Damage Contact Resistance: 60 m MAX Dielectric Strength: Must meet 4.1.3 Insulation Resistance: 20 M MIN |
| Environmental Performance: Temperature Cycling | 5 cycles of: a) -553 30 minutes; b) 852 30 minutes. | Appearance: No Damage Contact Resistance: 60 m MAX |
| Environmental Performance: Salt Spray | Mate applicable FPC/FFC; 24 4 hours exposure to a salt spray from the 51% solution at 352. Wash with room temperature water after test; then dry at room temperature. | Appearance: No Damage, Corrosion Contact Resistance: 60 m MAX |
| Environmental Performance: SO2 Gas | Mate applicable FPC/FFC; 24 hours exposure to 50 5ppm SO2 gas at 402. | Contact Resistance: 60 m MAX |
| Environmental Performance: NH3 Gas | Mate applicable FPC/FFC; 40 minutes exposure to NH3 gas evaporating from 28% Ammonia solution. | Appearance: No Damage Contact Resistance: 60 m MAX |
| Solderability: Solder Wetting | Soldering Time: 20.5 sec. Soldering Temperature: 2455. 0.2 mm from terminal tip. | Wetting Area: 95% |
| Resistance to Soldering Heat | Soldering Time: 305 sec. Soldering Temperature: 2455. Perform at least 5 times. | Appearance: No Damage, Deformation |
| Name | Material | Remark |
|---|---|---|
| Main body | LCP UL 94V-0 | |
| Housing Lock | LCP UL 94V-0 | |
| Terminal | Phosphor Bronze | Metal surface plated with tin |
| Contact | Phosphor Bronze | Metal surface plated with tin |
