This specification covers the 0.5 mm Pitch FPC/FFC Connectors.
| Item | Test Condition | Requirement |
|---|---|---|
| Rated Voltage (MAX) | 30V [AC/DC(Virtual value)50Hz] | |
| Rated Current (MAX) | 0.2A | |
| Ambient temperature Range | -25+85 | |
| Contact Resistance | Mate applicable FPC/FFC and measure by dry circuit, 20mV MAX, 10mA. | 100 m MAX |
| After Repeated Insertion and Withdrawal (20 cycles) | 60 m MAX | |
| Insulation Resistance | Mate applicable FPC/FFC and apply 500V DC between adjacent terminal or ground. | 500M MIN |
| After Humidity Test | 20 M MIN | |
| Dielectric Strength | Mate applicable FPC/FFC and apply 250V AC (virtual value) for 1 minute between adjacent terminal or ground. No Breakdown. | No Breakdown |
| After Humidity Test | Must meet 4.1.3 | |
| Locking and Withdrawal Force | Insert and extract applicable FFC (0.3mm thickness) at the speed rate of 253mm/minute. | Locking: 1.96*n (N) MAX Withdrawal: 0.49*n (N) MIN |
| Terminal/Housing Retention Force (Pull terminal outwards at 253mm/minute) | 0.4N MIN | |
| Temperature Rise | Carrying rated current load. (UL 498) | 30 MAX |
| Vibration | DC 1mA under energized state; Vibration along XYZ axes; Amplitude: 1.5mm P-P; Sweep time: 10-55-10Hz/min; Duration: 2 hours in each axis. | Appearance: No Damage Contact Resistance: 60 m MAX Discontinuity: 1 ms MAX |
| Shock (DC 1mA under energized state; 490m/s{50G}, 3 strokes in each of 6 directions) | Appearance: No Damage Discontinuity: 1 ms MAX | |
| Heat Resistance | Mate applicable FPC/FFC; Place in 852 air for 96 hours; then return to room temperature for 1-2 hours. | Appearance: No Damage Contact Resistance: 60 m MAX |
| Cold Resistance | Mate applicable FPC/FFC; Place in -402 air for 96 hours; then return to room temperature for 1-2 hours. | Appearance: No Damage Contact Resistance: 60 m MAX |
| Humidity | Mate applicable FPC/FFC; Place in 402, 90-95% RH air for 96 hours; measure within 0.5 hours after returning to room temperature. | Appearance: No Damage Contact Resistance: 60 m MAX Dielectric Strength: Must meet 4.1.3 Insulation Resistance: 20 M MIN |
| Temperature Cycling | Mate applicable FPC/FFC; 5 cycles of: a) -553 for 30 minutes; b) 852 for 30 minutes; with 10-15 minutes at room temp/humidity in between. | Appearance: No Damage Contact Resistance: 60 m MAX |
| Salt Spray | Mate applicable FPC/FFC; 48 4 hours exposure to a salt spray from a 51% solution at 352. Wash with room temp water after test; then dry at room temp. | Appearance: No Damage, No Corrosion Contact Resistance: 60 m MAX |
| SO2 Gas Resistance | Mate applicable FPC/FFC; 24 hours exposure to 505ppm SO2 gas at 402. | Contact Resistance: 60 m MAX |
| NH3 Gas Resistance | Mate applicable FPC/FFC; 40 minutes exposure to NH3 gas evaporating from 28% Ammonia solution. | Appearance: No Damage Contact Resistance: 60 m MAX |
| Solder ability | Dip terminal tip 0.2mm from the reference plane into a 2455 tin bath for 20.5 sec. | Solder Wetting: 95% coverage |
| Resistance to Soldering Heat | Expose to 2455 hot air for 305 sec; perform at least 5 times. | Appearance: No Damage, No Deformation |
| Name | Material | Remark |
|---|---|---|
| Main body | LCP UL 94V-0 | |
| Housing Lock | LCP UL 94V-0 | |
| Terminal | Phosphor Bronze | Metal surface plated tin |
| Contact | Phosphor Bronze |
