Scope: This specification covers the 0.3mm Pitch FPC/FFC Connectors.
Product Name: FFC/FPC Flat Cable Connector
Application: Used for connecting flexible flat cables (FFC) and flexible printed circuits (FPC) with a 0.3mm pitch.
Hanxia Electronic
Shenzhen, China
HX FPC 0.3-15P XGXJ H1.0
14
UL 94V-0 (for Housing/Lock)
| Item | Requirement | Test Condition |
|---|---|---|
| Rated Voltage (MAX) | 30V [AC/DC (Virtual value) 50Hz] | |
| Rated Current (MAX) | 0.2A | |
| Ambient Temperature Range | -25 ~ +85 | |
| Contact Resistance | 20 m MAX | Mate applicable FPC/FFC and measure by dry circuit, 20mV MAX, 10mA. |
| Insulation Resistance | 500M MIN | Mate applicable FPC/FFC and apply 500V DC between adjacent terminals or ground. |
| Dielectric Strength | No Breakdown | Mate applicable FPC/FFC and apply 200V AC (virtual value) for 1 minute between adjacent terminals or ground. |
| Locking and Withdrawal Force | Locking: 1.96*n (N) MAX Withdrawal: 0.49*n (N) MIN | Insert and extract applicable FFC at the speed rate of 253mm/minute. (n=number of positions) |
| Terminal/Housing Retention Force | 3.92N MIN | Pull the terminal at the speed rate of 25 3mm per minute. |
| Repeated Insertion and Withdrawal | Contact Resistance: 60 m MAX | Insertion and withdrawal actuator up to 20 cycles at the speed rate of less than 10 cycles/minute. |
| Temperature Rise | 30 MAX | Carrying rated current load. (UL 498) |
| Vibration | Contact Resistance: 60 m MAX Discontinuity: 1 ms MAX. Appearance: No Damage | DC 1mA under energized state; vibrate along XYZ three directions; Amplitude: 1.5mm P-P; Sweep time: 10-55-10Hz/min; Duration: 2 hours in each X,Y,Z axes. |
| Shock | Appearance: No Damage Discontinuity: 1 ms MAX. | DC 1mA under energized state; impact in 6 mutually perpendicular directions; 490m/s {50G}, 3 strokes in each X,Y,Z axes. |
| Heat Resistance | Appearance: No Damage Contact Resistance: 60 m MAX | Mate applicable FPC/FFC; placed in 852 air for 96 hours; then return to room temperature for 1-2 hours. |
| Cold Resistance | Appearance: No Damage Contact Resistance: 60 m MAX | Mate applicable FPC/FFC; placed in -402 air for 96 hours; then return to room temperature for 1-2 hours. |
| Humidity | Appearance: No Damage Contact Resistance: 60 m MAX Dielectric Strength: Must meet 4.1.3 Insulation Resistance: 20 M MIN | Temperature: 402; Relative Humidity: 90-95%; Duration: 96 Hours; then measure within 0.5 hours after returning to room temperature. |
| Temperature Cycling | Appearance: No Damage Contact Resistance: 60 m MAX | 5 cycles of: a) -553 30 minutes b) 852 30 minutes, with 10-15 minutes at normal temperature and humidity between cycles. |
| Salt Spray | Appearance: No Damage, No Corrosion Contact Resistance: 60 m MAX | 24 4 hours exposure to a salt spray from a 51% solution at 352. After test, wash with room temperature water and dry at room temperature. |
| SO2 Gas Resistance | Contact Resistance: 60 m MAX | 24 hours exposure to 50 5ppm SO2 gas at 402. |
| NH3 Gas Resistance | Appearance: No Damage Contact Resistance: 60 m MAX | 40 minutes exposure to NH3 gas evaporating from 28% Ammonia solution. |
| Solderability | Solder Wetting: 95% coverage | Soldering Time: 20.5 sec. Soldering Temperature: 2455 0.2 mm from terminal tip. |
| Resistance to Soldering Heat | Appearance: No Damage, No Deformation | Soldering Time: 305 sec. Soldering Temperature: 2455 Performed at least 5 times in a 2455 hot air oven. |
| Name | Material | Remarks |
|---|---|---|
| Main body | LCP UL 94V-0 | Metal surface plated with tin |
| Housing Lock | LCP UL 94V-0 | |
| Terminal/Contact | Phosphor Bronze |
