Function: Connects FPC/FFC cables.
Usage: This specification covers the 0.5mm Pitch FPC/FFC Connectors.
Application: Suitable for 0.5mm pitch FPC/FFC connectors.
Shenzhen Hanxia Electronic Co., Ltd
China
HX0.5-10P XJH2.0 043
FFC/FPC Flat Cable Connector
N/A
LCP UL 94V-0
LCP UL 94V-0
Phosphor Bronze
Tinned
| Item | Test Condition | Requirement |
|---|---|---|
| Rated Voltage (MAX) | AC/DC (Virtual value) 50Hz 50V | |
| Rated Current (MAX) | 0.4A | |
| Ambient Temperature Range | -25+85 | |
| Contact Resistance | Mate applicable FPC/FFC and measure by dry circuit, 20mV MAX, 10mA. | 30 m MAX |
| Insulation Resistance | Mate applicable FPC/FFC and apply 500V DC between adjacent terminal or ground. | 500M MIN |
| Dielectric Strength | Mate applicable FPC/FFC and apply 200V AC (virtual value) for 1minute between adjacent terminal or ground. | No Breakdown |
| Locking and Withdrawal Force | Insert and extract applicable FFC (0.3mm thickness) at the speed rate of 253mm/minute. 'n' is the number of contacts. | Locking: 1.96*n (N) MAX Withdrawal: 0.49*n (N) MIN |
| Terminal/Housing Retention Force | Pull the terminal at the speed rate of 25 3mm per minute. | 3.92N MIN |
| Repeated Insertion and Withdrawal | Insertion and withdrawal actuator up to 20 cycles at the speed rate of less than 10 cycles/minute (no power). | Contact Resistance: 60 m MAX |
| Temperature Rise | Carrying rated current load. (UL 498) | 30 MAX |
| Vibration | DC 1mA under power. Vibration along X, Y, Z axes. Amplitude: 1.5mm P-P. Sweep time: 10-55-10Hz/min. Duration: 2 hours in each axis. | Appearance: No Damage Contact Resistance: 60 m MAX Discontinuity: 1 ms MAX |
| Shock | DC 1mA under power. 490m/s {50G}, 3 strokes in each of 6 directions. | Appearance: No Damage Discontinuity: 1 ms MAX |
| Heat Resistance | Mate applicable FPC/FFC. Place in 852 air for 96 hours, then return to room temperature for 1-2 hours. | Appearance: No Damage Contact Resistance: 60 m MAX |
| Cold Resistance | Mate applicable FPC/FFC. Place in -402 air for 96 hours, then return to room temperature for 1-2 hours. | Appearance: No Damage Contact Resistance: 60 m MAX |
| Humidity | Mate applicable FPC/FFC. Place in 402, 90-95% RH air for 96 hours, then measure within 0.5 hours after returning to room temperature. | Appearance: No Damage Contact Resistance: 60 m MAX Dielectric Strength: Must meet 4.1.3 Insulation Resistance: 20 M MIN |
| Temperature Cycling | Mate applicable FPC/FFC. 5 cycles of: a) -553 for 30 minutes, b) 852 for 30 minutes, with 10-15 minutes at room temp/humidity between cycles. | Appearance: No Damage Contact Resistance: 60 m MAX |
| Salt Spray | Mate applicable FPC/FFC. 24 4 hours exposure to a 51% salt spray solution at 352. Wash with room temp water after test and dry at room temp. | Appearance: No Damage, No Corrosion Contact Resistance: 60 m MAX |
| SO2 Gas Resistance | Mate applicable FPC/FFC. 24 hours exposure to 505ppm SO2 gas at 402. | Contact Resistance: 60 m MAX |
| NH3 Gas Resistance | Mate applicable FPC/FFC. 40 minutes exposure to NH3 gas evaporating from 28% Ammonia solution. | Appearance: No Damage Contact Resistance: 60 m MAX |
| Solderability | Soldering Time: 20.5 sec. Soldering Temperature: 2455. Measure at 0.2 mm from terminal tip. | Solder Wetting: 95% wetting area |
| Resistance to Soldering Heat | Soldering Time: 305 sec. Soldering Temperature: 2455. Perform at least 5 times. | Appearance: No Damage, No Deformation |
