Scope: This specification covers the 0.5 mm Pitch FPC/FFC Connectors.
Product Name: FFC/FPC Flat Cable Connector
| Item | Specification | Requirement |
| Rated Voltage (MAX) | 30V [AC/DC (Virtual value) 50Hz] | |
| Rated Current (MAX) | 0.2A | |
| Ambient Temperature Range | -25+85 | |
| Contact Resistance | Mate applicable FPC/FFC and measure by dry circuit, 20mV MAX, 10mA. | 100 m MAX |
| Insulation Resistance | Mate applicable FPC/FFC and apply 500V DC between adjacent terminal or ground. | 500M MIN |
| Dielectric Strength | Mate applicable FPC/FFC and apply 250V AC (Virtual value) for 1 minute between adjacent terminal or ground. | No Breakdown |
| Locking and Withdrawal Force | Insert and extract applicable FFC at the speed rate of 253mm/minute. | Locking: 1.96*n (N) MAX Withdrawal: 0.49*n (N) MIN |
| Terminal/Housing Retention Force | Pull the terminal at the speed rate of 25 3mm per minute | 0.4N MIN |
| Repeated Insertion and Withdrawal | Insertion and withdrawal actuator up to 20 cycles at the speed rate of less than 10 cycles/minute | Contact Resistance: 60 m MAX |
| Temperature Rise | Carrying rated current load. (UL 498) | 30 MAX |
| Vibration | DC 1mA under power; Vibration along XYZ three axes; Amplitude: 1.5mm P-P; Sweep time: 10-55-10Hz/min; Duration: 2 hours in each X.Y.Z. axes. | Contact Resistance: 60 m MAX Discontinuity: 1 ms MAX |
| Shock | DC 1mA under power; 490m/s2{50G}, 3 strokes in each X.Y.Z. axes. | Appearance: No Damage Discontinuity: 1 ms MAX |
| Heat Resistance | Mate applicable FPC/FFC; Place in 852 air for 96 hours; then return to room temperature for 1-2 hours. | Appearance: No Damage Contact Resistance: 60 m MAX |
| Cold Resistance | Mate applicable FPC/FFC; Place in -402 air for 96 hours; then return to room temperature for 1-2 hours. | Appearance: No Damage Contact Resistance: 60 m MAX |
| Humidity | Mate applicable FPC/FFC; Place in 402, 90-95% RH air for 96 hours; measure within 0.5 hours after returning to room temperature. | Appearance: No Damage Contact Resistance: 60 m MAX Dielectric Strength: Must meet 4.1.3 Insulation Resistance: 20 M MIN |
| Temperature Cycling | Mate applicable FPC/FFC; 5 cycles of: a) -553 30 minutes b) 852 30 minutes | Appearance: No Damage Contact Resistance: 60 m MAX |
| Salt Spray | Mate applicable FPC/FFC; 48 4 hours exposure to a salt spray from the 51% solution at 352. After test, wash with room temperature water and dry. | Appearance: No Damage, No Corrosion Contact Resistance: 60 m MAX |
| SO2 Gas Resistance | Mate applicable FPC/FFC; 24 hours exposure to 505ppm SO2 gas at 402. | Contact Resistance: 60 m MAX |
| NH3 Gas Resistance | Mate applicable FPC/FFC; 40 minutes exposure to NH3 gas evaporating from 28% Ammonia solution. | Appearance: No Damage Contact Resistance: 60 m MAX |
| Solderability | Immerse the front end of the terminal at 0.2mm from the reference plane into a 2455 tin bath for 20.5 sec. | Solder Wetting: 95% coverage |
| Resistance to Soldering Heat | 305 sec. Soldering Time. 2455 Soldering Temperature. At least 5 times. | Appearance: No Damage, No Deformation |
