Function: FPC Connector
Usage: This specification covers the 0.5PH 2.0H ZIF FPC series. It is designed for connecting Flexible Printed Circuits (FPC) and Flexible Flat Cables (FFC) in various electronic applications.
Application Scenarios: Suitable for electronic devices requiring compact and reliable FPC/FFC connections.
| Item | Standard | Test Condition | Procedure |
|---|---|---|---|
| Operating Voltage | 50VAC/DC | ||
| Current Rating | 0.5AAC/DC | ||
| Operating Temperature | -25+85 | ||
| Contact Resistance (Initial) | 30m Ohm Max. | Mate applicable FPC and measure by dry circuit 20Mv Msx,10mA | |
| Dielectric withstanding Voltage | [250]VAC for 1 minute | Test between adjacent circuits of unmated connector. | NO Breakdown |
| Insulation Resistance | 500 M Ohm Min. | [500]VAC for 1 minute Test between adjacent circuits of unmated connector. | |
| Contact/Peg Retention Force | 0.250kgf Min. | Apply axial pull out force at the rate of [25.43]mm/min on the terminal assembled in the housing. | |
| Actuator Retention Force | 0.200kgf/Pin Max. | Operation Speed:[25.43] mm/min Measure the force required to mated connector. | |
| FPC/FFC Retention Force | 0.030kgf/Pin Min.(PIN>=17) 0.500kgf Min.(PIN<17) | Operation Speed:[25.43] mm/min Measure the force required to unmated connector. | |
| Durability | 20 Cycles | Operation Speed: (10) cycle-max./ min | Contact Resistance: 60m Ohm Max; Appearance: No damage |
| Vibration | Discontinuity: 1u sec. Max.; Appearance: No damage; Contact Resistance: 60mOhm Max | Amplitude1.52m; Frequency; 10~55~10HZ; Vibration time:2 hours for 3 axis total 6 hours. | |
| Mechanical Shock | Discontinuity: 1u sec. Max. | The connectors shall be soldered on the P.C. board. /Acceleration50G. Time: 11ms.(half sine wave). Cycle: 3 cycle for 3 axis total 9 cycle. {JIS COO41/MIL-STD-202Method213} | |
| Temperature Rising | 30 Max | Mate applicable FPC and measure the temperature rise of contact when the maximum AC mated current is. | |
| Solder ability | 95% of immersed area must show no voids, Pinholes | Tip of Solder tails and fitting nails into the molten solder(held at 245 5) up to 0.1mm from the bottom of the housing for 30.05sec | |
| Resistance to Reflow Soldering Heat | Appearance: No damage | Pre Heat:150~180,9030sec. Heat230 Min.,3010sec Peak Temp.:260+0/-5, 10sec. Or less Duration3 cycles Refer to Fig.4 | |
| Thermal Shock | Contact Resistance: 60mOhm Max; Appearance: No damage | Temperature range form -55to +85 .Start from -55 ,after 30 min. Change to +85;chang time is no more than 30 seconds. Total 5 cycles. {MIL-STD-202107D,A} | |
| Humidity-Temperature Cycle | Insulation Resistance: 100M Ohm Min | 40 20C in temperature and 90~95%RH for 96 hours. After testing connector shall be left alone for 1 to 2 hours in a room ambient. {EIA-364-31A, Method , condition A} | |
| Temperature Life | Contact Resistance: 60mOhm Max; Appearance: No damage | Mated, Connector 85, 250 hours | |
| Salt Spray | Contact Resistance: 60mOhm Max | Salt concentration: 5%/ Temperature: 3520C,Testing time: 242 hours, After salt is removed by running water and a drop is removed, it is measured. {EIA-364-26A, Condition A} |
