LIF Series Connector JUSHUO AF125-S18WCC-00 Supporting 0.3mm Thickness FFC and Rated Voltage 125V AC DC
Product Overview
This specification covers the 1.25mm Pitch FPC/FFC Connectors, LIF series, designed for applications requiring reliable connections with flexible flat cables. These connectors are suitable for FFC with a thickness of 0.3+/-0.03mm and a 1.25mm pitch. They offer a rated voltage of 125V [AC(rms)/DC] and a rated current of 1.0A, operating within an ambient temperature range of -40 to +85. The LIF series connectors are engineered for robust performance, meeting stringent electrical, mechanical, and environmental standards.
Product Attributes
- Brand: SHENZHEN JUSHUO ELECTRONIC CO.,LTD
- Series: LIF
- Housing Material: LCP ( or UL 94V-0)
- Contact Material: Phosphor Bronze C5191R-EH
- Contact Plating: Ni Base 40u min, Surface Sn 80120u or Au:0.8umin
- FFC Thickness Compatibility: 0.3+/-0.03mm
- Pitch: 1.25mm
Technical Specifications
| Category | Item | Test Condition | Requirement |
|---|---|---|---|
| Ratings | Rated Voltage (MAX) | 125V [AC(rms)/DC] | |
| Rated Current (MAX) | 1.0A | ||
| Ambient Temperature Range | -40+85 | ||
| Electrical Performance | Contact Resistance | Mate applicable FPC/FFC and measure by dry circuit, 20mV MAX, 10mA. | 30 m MAX |
| Insulation Resistance | Mate applicable FPC/FFC and apply 500V DC between adjacent terminal or ground. | 500M MIN | |
| Dielectric Strength (rms) | Mate applicable FPC/FFC and apply 200V AC (rms) for 1minute between adjacent terminal or ground. | No Breakdown | |
| Mechanical Performance | Locking and Withdrawal Force | Insert and extract applicable FFC at the speed rate of 253mm/minute (0.3mm thickness FFC). | Locking: 1.96*n (N) MAX Withdrawal: 0.49*n (N) MIN |
| Terminal/Housing Retention Force | Pull the terminal at the speed rate of 25 3mm per minute. | 5.9 N MIN | |
| Environmental Performance | Repeated Insertion and Withdrawal | Insertion and withdrawal up to 20 cycles at the speed rate of less than 10 cycles/minute (no power). | Contact Resistance: 40 m MAX |
| Temperature Rise | Carrying rated current load. (UL 498) | 30 MAX | |
| Vibration | DC 1mA under power; Amplitude: 1.5mm P-P; Sweep time: 10-55-10Hz/min; Duration: 2 hours in each X, Y, Z axes. | Appearance: No Damage Contact Resistance: 40 m MAX Discontinuity: 1 ms.MAX. | |
| Shock | DC 1mA under power; 490m/s {50G}, 3 strokes in each X, Y, Z axes. | Appearance: No Damage Discontinuity: 1 ms.MAX. | |
| Heat Resistance | 852, 96 hours exposure, then return to room temperature for 1-2 hours. | Appearance: No Damage Contact Resistance: 40 m MAX | |
| Cold Resistance | -402, 96 hours exposure, then return to room temperature for 1-2 hours. | Appearance: No Damage Contact Resistance: 40 m MAX | |
| Humidity | Temperature: 402; Relative Humidity: 90-95%; Duration: 96 Hours; then measure within 0.5 hours at room temperature. | Appearance: No Damage Contact Resistance: 40 m MAX Dielectric Strength: Must meet 4.1.3 Insulation Resistance: 50 M MIN | |
| Temperature Cycling | 5 cycles of: a) -553 30 minutes; b) 852 30 minutes; with 10-15 minutes at room temperature and humidity between cycles. | Appearance: No Damage Contact Resistance: 40 m MAX | |
| Salt Spray | 48 hours exposure to a salt spray from the 51% solution at 352. After test, wash with room temperature water and dry. | Appearance: No Damage, Corrosion Contact Resistance: 40 m MAX | |
| SO2 Gas Resistance | 24 hours exposure to 505ppm SO2 gas at 402. | Contact Resistance: 40 m MAX | |
| NH3 Gas Resistance | 40 minutes exposure to NH3 gas evaporating from 28% Ammonia solution. | Appearance: No Damage Contact Resistance: 40 m MAX | |
| Other Performance | Solderability | Soldering Time: 20.5 sec. Soldering Temperature: 2455 0.2 mm from terminal tip | Solder Wetting: 95% or more |
| Resistance to Soldering Heat (Wave Soldering) | Parts shall withstand the following wave soldering conditions twice: total cycle time 6 min - peak temperature 250 5 for 5~10s - temperature 80-120 for 8~12s - air and/or nitrogen atmosphere. See temperature profile in [7]. | Appearance: No Damage, Deformation |
Packaging, Transportation, and Storage
Packing: Unless otherwise specified, connectors in this series are packaged in PE bags.
Transportation: Any vehicle can be adopted for transportation, provided it is protected from rain, direct sunlight, and mechanical damage.
Storage: Packaged connectors should be stored in a warehouse with ambient temperature between -10 to +40, relative humidity not exceeding 80%, and in an environment free from acidic, alkaline, or other corrosive gases. Recommended storage conditions: Temperature: -5+35, Relative humidity: 70%. Storage duration is 6 months; re-qualification testing is required if storage exceeds 6 months.
2409272303_JUSHUO-AF125-S18WCC-00_C22470644.pdf
