phone jack connector hanxia HX PJ-242 095 designed for stable electrical performance and durability
Manufacturer:
hanxia
Description:
2.5mm Headphone Jack 500mA 30V Surface Mount
Category:
Audio Connectors/Audio Connectors
Specifications
Operating Temperature:
-30℃~+70℃
Connector Type:
2.5mm耳机座
Voltage Rating (Max):
30V
Current Rating:
500mA
Mfr. Part #:
HX PJ-242 095
Package:
SMD
Model Number:
HX PJ-242 095
Introduction
Product Overview
This document specifies the requirements for the HX PJ-242 095 Phone Jack, manufactured by Shenzhen Hanxia Electronic Co., Ltd. It details the product's technical specifications, testing conditions, and performance criteria to ensure reliable operation within the specified temperature range of -30C to +70C.
Product Attributes
- Brand: (Shenzhen Hanxia Electronic Co., Ltd)
- Model: HX PJ-242 095
- Origin: Shenzhen, China
Technical Specifications
| Item | Test Conditions | Performance | Specification |
| Connection Force | Measured after connecting and disconnecting using standard plug gauge 3 times. | 320N | |
| Disconnection Force | Measured after connecting and disconnecting using standard plug gauge 3 times. | 320N | |
| Terminal Strength | A static load of 0.1N/m (1kgf/cm) shall be applied to the tip of the terminal for 1 min in any direction. There shall be no damage to the terminal such as cracks, looseness or play. Electrical and mechanical characteristics shall be satisfied. | ||
| Contact Resistance | Measured at small current (100mA or less) 1000Hz | 30m | |
| Insulation Resistance | Apply a voltage of 500V DC for 1 min to following portions: (1) Between body and conductor (2) Between conductors not to be contact (3) Between conductors not to be when plug is inserted. | 100M | |
| Dielectric Strength | Without damage to parts arcing or breakdown etc. AC 500V ims (50~60Hz) for 1 min. Trip current: 0.5mA. Tested between: (1) Body and conductor (2) Conductors not to be contact (3) Conductors not to be when plug is inserted. | ||
| Solderability Test | The top of the terminals shall be dipped 1mm in the solder bath of 2405 for 30.5 seconds. | (1) Solder wetting time shall be 3 seconds or less. (2) The area of soldering should be over 75%. | |
| Resistance to Soldering Heat Test (Reflow Soldering) | Reflow soldering conditions: Preheat: Temperature on the copper foil surface should reach 180, 120s after the P.C.B entered into the soldering equipment. Tallest temperature: Temperature on the copper foil surface should reach the peak temperature of 2605 within 20 seconds. | Without deformation of case or excessive looseness of terminals. Electrical characteristics shall be satisfied. | |
| Resistance to Soldering Heat Test (Soldering Iron) | Soldering iron method: Bit temperature 3305. Application time of soldering iron 30.5 sec. However, excessive pressure shall not be applied to the terminal. | Without deformation of case or excessive looseness of terminals. Electrical characteristics shall be satisfied. | |
| Humidity Test | The jack shall be stored at a temperature of 402 and a humidity of 90% to 96% for 96 Hr, then the jack shall be maintained at standard atmospheric condition for 1 Hr for other procedures. | There shall be no damage on appearance. Mechanical and electrical characteristics shall be satisfied. | |
| Heat Test | The jack shall be stored at a temperature of 702 for 96 hours, and then it shall be subjected to the controlled recovery measurement. | There shall be no damage on appearance. Mechanical and electrical characteristics shall be satisfied. | |
| Cold Test | The jack shall be stored at a temperature of -253 for 96 hours and then it shall be subjected to the controlled recovery conditions for 1 hour after which. | There shall be no damage on appearance. Mechanical and electrical characteristics shall be satisfied. | |
| Life Test | At rating condition (non-inductive load). Connection and disconnection shall be made 5000 cycles at a speed 10 to 20 cycles / min. | (1) Contact resistance shall be 0.1. (2) Disconnection force shall be 3 to 20N. (3) Other: Mechanical and electrical characteristics shall be satisfied. | |
| Cold & Heat Shock Test | The jack shall be subjected to 5 cycles of the following conditions, and then shall be returned and allowed to remain in room ambient condition for 30 minutes. | Product cannot deform or crack. Insertion & Extraction Force: 3 to 20N. Contact Resistance: Max. 30m. Insulation Resistance: Min. 100 M. Dielectric Withstanding Voltage: 500VAC/min (between terminals). |
2409272202_hanxia-HX-PJ-242-095_C19189140.pdf
Send RFQ
Stock:
MOQ:
