hanxia HX PJ-327F-J phone jack providing stable electrical performance and mechanical strength for telecom
Manufacturer:
hanxia
Description:
3.5mm Headphone Jack 500mA 30V Surface Mount
Category:
Audio Connectors/Audio Connectors
Specifications
Operating Temperature:
-30℃~+70℃
Connector Type:
3.5mm耳机座
Voltage Rating (Max):
30V
Current Rating:
500mA
Mfr. Part #:
HX PJ-327F-J
Package:
SMD
Model Number:
HX PJ-327F-J
Introduction
Product Overview
This document outlines the specifications for the HX PJ-327F-J Phone Jack, a component designed for use within a practical temperature range of -30C to +70C. It details the electrical, mechanical, and durability characteristics, including insertion/disconnection forces, contact and insulation resistance, dielectric strength, solderability, and resistance to heat and cold.
Product Attributes
- Brand: (Shenzhen Hanxia Electronic Co., Ltd)
- Model No.: HX PJ-327F-J
- Product Name: PHONE JACK
- Origin: Shenzhen, China
Technical Specifications
| Item | Test Conditions | Performance | |||
| 1 | CONNECTION FORCE | MEASUREMENT SHALL BE MADE AFTER CONNECTING AND DISCONNECTING USING STANDARD PLUG GAUGE 3 TIMES | PLUG GAUGE 3 | 320N | |
| 2 | DISCONNECTION FORCE | MEASUREMENT SHALL BE MADE AFTER CONNECTING AND DISCONNECTING USING STANDARD PLUG GAUGE 3 TIMES | PLUG GAUGE 3 | 320N | |
| 3.1 | CONTACT RESISTANCE | MEASURED AT SMALL CURRENT 100m A OR LESS 1000Hz | 100 m A | 30m | |
| 3.2 | INSULATION RESISTANCE | APPLY A VOLTAGE OF 500V DC FOR 1 MIN TO FOLLOWING PORTIONS AFTER WHICH MEASUREMENT SHALL BE MADE: (1) BETWEEN BODY AND CONDUCTOR (2) BETWEEN CONDUCTORS NOT TO BE CONTACT (3) BETWEEN CONDUCTORS NOT TO BE WHEN PLUG IS INSERTED | DC 500V 1 MIN 500V DC 1 1 2 3 | 100M | |
| 3.3 | DIELECTRIC STRENGTH | WITHOUT DAMAGE TO PARTS ARCING OR BREAKDOWN ETC AC 500V ims(50~60Hz)FOR 1 MIN TRIP CURRENT:0.5mA (1) BETWEEN BODY AND CONDUCTOR (2) BETWEEN CONDUCTORS NOT TO BE CONTACL (3) BETWEEN CONDUCTORS NOT TO BE WHEN PLUG | ITEM TEST CONDITIONS PERFORMANCE 3.3 DIELECTRIC STRENGTH WITHOUT DAMAGE TO PARTS ARCING OR BREAKDOWN ETC AC 500V ims(50~60Hz)FOR 1 MIN TRIP CURRENT:0.5mA (1) BETWEEN BODY AND CONDUCTOR (2) BETWEEN CONDUCTORS NOT TO BE CONTACL (3) BETWEEN CONDUCTORS NOT TO BE WHEN PLUG AC 500V 50Hz/min 1 0.5mA, : (1) (2) (3) | ||
| 4.1 | SOLDERA- BILITY TEST | THE TOP OF THE TERMINALS SHALL BE DIPPED 1mm IN THE SOLDER BATH OF 2405 FOR 30.5 SECONDS | 1mm ,2405,3 0.5 | 1SOLDER WETTING TIME SHALL BE 3 SEC OR LESS 2THE AREA OF SOLDERING SHOULD BE OVER 75% | 3 75% |
| 4.2 | RESISTANCE TO SOLDERING HEAT TEST | REFLOW SOLDERING CONDITIONS: PREHEAT:TEMPERATURE ON THE COPPER FOIL SURFACE SHOULD REACH 180.120S AFTER THE P.C.B ENTERED INTO THE SOLDERING EQUIPMENT. TALLEST TEMPERATURE:TEMPERATURE ON THE COPPER FOIL SURFACE SHOULD REACH THE PEAK TEMPERATURE OF 2605WITH IN 20 SECONDS. | :180, 120s :260520 | WITHOUT DEFOR MATION OF CASE OR EXCESSIVE LOOSENESS OF TEMINALS ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED | |
| 4.2 | RESISTANCE TO SOLDERING HEAT TEST | SOLDERING IRON METHOD: BIT TEMPERATURE 3305 APPLICATION TIME OF SOLDERING IRON30.5 SEC HOWEVER EXCESSIVE PRESSURE SHALL NOT BE APPLIED TO THE TERMINAL | 3305 30.5 | WITHOUT DEFORMATION OF CASE OR EXCESSIVE LOOSENESS OF TEMINALS ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED | |
| 4.3 | HUMIDITY TEST | THE JACK SHALL BE STORED AT A TEMPERATURE OF 402 AND A HUMIDITY OF 90%TO 96% FOR 96 Hr,THEN THE JACK SHALL BE MAINTAINED AT STANDARD ATMOSPHERIC CONDITION FOR 1 Hr FOR OTHER PROCEDURES | 402 90~96% Hr 96 1 | THERE SHALL BE NO DAMAGE ON APPEARANCE MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED | |
| 4.4 | HEAT TEST | THE JACK SHALL BE STORED AT A TEMPERATURE OF702 FOR 96 HOURSAND THEN IT SHALL BE SUBJECTED TO THE CONTROLLED RECOVERY MBASURBM | 70296 1 | THERE SHALL BE NO DAMAGE ON APPEARANCE MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED | |
| 4.5 | COLD TEST | THE JACK SHALL BE STORED AT A TEMPERATURE OF-253 FOR 96 HOURS AND THEN IT SHALL BE SUBJECTED TO THE CONTROLLED RECOVERY CONDITIONS FOR 1 HOUR AFTER WHICH | -25396 1 | THERE SHALL BE NO DAMAGE ON APPEARANCE MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED | |
| 4.6 | LIFE TEST | AT RATING CONDITION NON-INDUCTIVE LOAD CONNECTION AND DISCONNECTION SHALL BE MADE 5000 CYCLES AT A SPEED 10 TO 20 CYCLES / MIN | ()1 10~20 5000 | 1.CONTACT RESISTANCE SHALL BE 0.1 2.DISCONNECTION FORCE SHALL BE 3 TO 20N 3.MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED | (1) 0.1 (2) 3~20N (3) :, |
| COLD&HEAT SHOCK TEST | THE JACK SHALL BE SUBJECTED TO5 CYCLES OF THE FOLLOWING CONDITIONS SHOWED IN THE FIGURE,AND THEN SHALL RETURNED AND ALLOWED TO REMAIN IN ROOM AMBIENT CONDITION FOR 30 MINUTES | 5 30 | THERE SHALL BE NO DEFORMATION OR CRACKS IN MOLDED PART. INSERTION EXTRACTION FORCE:3 TO 20N CONTACT RESISTANCE:MAX.30M INSULATION RESISTANCE: MIN.100 M DIELECTRIC WITHSTANDING VOLTAGE: 500VAC/MIN(BETWEEN TERMINALS) | 3N 20N 30m 100 M 500VAC |
2409272202_hanxia-HX-PJ-327F-J_C19189092.pdf
Send RFQ
Stock:
MOQ:
