Industrial phone jack hanxia HX PJ-242 engineered for consistent connection force and terminal strength
Manufacturer:
hanxia
Description:
2.5mm Headphone Jack 500mA 30V Surface Mount
Category:
Audio Connectors/Audio Connectors
Specifications
Operating Temperature:
-30℃~+70℃
Connector Type:
2.5mm耳机座
Voltage Rating (Max):
30V
Current Rating:
500mA
Mfr. Part #:
HX PJ-242
Package:
SMD
Model Number:
HX PJ-242
Introduction
Product Overview
The HX PJ-242 is a Phone Jack designed and manufactured by Shenzhen Hanxia Electronic Co., Ltd. It is suitable for use within a practical temperature range of -30C to +70C and standard atmospheric conditions. This product is engineered to meet stringent performance, mechanical, and electrical specifications, ensuring reliability in various applications.
Product Attributes
- Brand: Shenzhen Hanxia Electronic Co., Ltd.
- Model No.: HX PJ-242
- Date: 2020.5.26
- Origin: Shenzhen, China
Technical Specifications
| Item | Test Conditions | Performance Specification |
|---|---|---|
| CONNECTION FORCE | Measurement shall be made after connecting and disconnecting using standard plug gauge 3 times. | 3-20N |
| PLUG GAUGE 3 | 3-20N | |
| DISCONNECTION FORCE | Measurement shall be made after connecting and disconnecting using standard plug gauge 3 times. | 3-20N |
| PLUG GAUGE 3 | 3-20N | |
| TERMINAL STRENGTH | A static load of 0.1N/m(1kgf/cm) shall be applied to the tip of the terminal for 1 min in any direction. There shall be no damage to the terminal such as cracks, looseness or play. Electrical and mechanical characteristics shall be satisfied. | N/A |
| 1 0.1N/m(1kgf/cm). | N/A | |
| CONTACT RESISTANCE | Measured at small current (100mA or less) 1000Hz | 30m |
| 100 m A | 30m | |
| INSULATION RESISTANCE | Apply a voltage of 500V DC for 1 min to following portions after which measurement shall be made: (1) Between body and conductor (2) Between conductors not to be contact (3) Between conductors not to be when plug is inserted | 100M |
| 500V DC 1 1 2 3 | 100M | |
| DIELECTRIC STRENGTH | AC 500V rms(50~60Hz) for 1 min. Trip current:0.5mA (1) Between body and conductor (2) Between conductors not to be contact (3) Between conductors not to be when plug is inserted | Without damage to parts arcing or breakdown etc. |
| AC 500V 50Hz/min 1 0.5mA, : (1) (2) (3) | ||
| SOLDERABILITY TEST | The top of the terminals shall be dipped 1mm in the solder bath of 2405 for 30.5 seconds. (1) Solder wetting time shall be 3 seconds or less (2) The area of soldering should be over 75% | N/A |
| 1mm ,2405,3 0.5 13 275% | N/A | |
| RESISTANCE TO SOLDERING HEAT TEST (Reflow Soldering) | Reflow soldering conditions: Preheat: Temperature on the copper foil surface should reach 180, 120s after the P.C.B entered into the soldering equipment. Tallest temperature: Temperature on the copper foil surface should reach the peak temperature of 2605 within 20 seconds. Without deformation of case or excessive looseness of terminals. Electrical characteristics shall be satisfied. | N/A |
| :180, 120s :260520 | N/A | |
| RESISTANCE TO SOLDERING HEAT TEST (Soldering Iron Method) | Bit temperature 3305. Application time of soldering iron 30.5 sec. However excessive pressure shall not be applied to the terminal. Without deformation of case or excessive looseness of terminals. Electrical characteristics shall be satisfied. | N/A |
| 3305 30.5 | N/A | |
| HUMIDITY TEST | The jack shall be stored at a temperature of 402 and a humidity of 90%to 96% for 96 Hr, then the jack shall be maintained at standard atmospheric condition for 1 Hr for other procedures. | N/A |
| 402 90~96% Hr 96 1 | N/A | |
| HEAT TEST | The jack shall be stored at a temperature of 702 for 96 hours, and then it shall be subjected to the controlled recovery. There shall be no damage on appearance. Mechanical and electrical characteristics shall be satisfied. | N/A |
| 70296 1 | N/A | |
| COLD TEST | The jack shall be stored at a temperature of -253 for 96 hours and then it shall be subjected to the controlled recovery conditions for 1 hour after which. There shall be no damage on appearance. Mechanical and electrical characteristics shall be satisfied. | N/A |
| -25396 1 | N/A | |
| LIFE TEST | At rating condition (non-inductive load) connection and disconnection shall be made 5000 cycles at a speed 10 to 20 cycles / min. (1) Contact resistance shall be 0.1 (2) Disconnection force shall be 3 to 20N (3) Mechanical and electrical characteristics shall be satisfied. | N/A |
| ()1 10~20 5000 (1) 0.1 (2) 3~20N (3) :, | N/A | |
| COLD&HEAT SHOCK TEST | The jack shall be subjected to 5 cycles of the following conditions, and then shall be returned and allowed to remain in room ambient condition for 30 minutes. There shall be no deformation or cracks in molded part. Insertion & extraction force: 3 to 20N. Contact resistance: Max. 30m. Insulation resistance: Min. 100 M. Dielectric withstanding voltage: 500VAC/min (between terminals). | N/A |
| 5 30 . 3N 20N 30m 100 M 500VAC | N/A |
2410121336_hanxia-HX-PJ-242_C5184834.pdf
Send RFQ
Stock:
MOQ:
