0.5mm Pitch Flexible Flat Cable Connector Hanxia HX FPC 0.5-10P HYH2.0 for Electronic Applications
Manufacturer:
hanxia
Description:
FFC/FPC Connector 10 Position 0.5mm Pitch Double-Sided Contacts, Top and Bottom Entry Surface Mount, Right Angle -25℃~+85℃
Category:
FFC, FPC (Flat Flexible) Connector Assemblies/FFC, FPC (Flat Flexible) Connector Assemblies
Specifications
Operating Temperature:
-25℃~+85℃
Locking Feature:
翻盖式
Number Of Contacts:
10P
Pitch:
0.5mm
Current Rating:
500mA
Voltage Rating (Max):
50V
Contact Type:
双侧触点/上下接
Mounting Type:
卧贴
FFC, FCB Thickness:
0.3mm
Contact Plating:
金
Contact Material:
磷青铜
Mfr. Part #:
HX FPC 0.5-10P HYH2.0
Package:
SMD,P=0.5mm,Surface Mount,Right Angle
Model Number:
HX FPC 0.5-10P HYH2.0
Introduction
Product Overview
This specification covers the 0.5mm Pitch FPC/FFC Connectors from Shenzhen Hanxia Electronic Co., Ltd. These connectors are designed for flexible flat cable applications.
Product Attributes
- Brand: Hanxia Electronic (HX)
- Origin: Shenzhen, China
- Certifications: UL 94V-0 (for LCP material)
Technical Specifications
| Item | Requirement | Test Condition | Specification |
| 3. RATINGS | |||
| Rated Voltage (MAX) | AC/DC (Virtual value) 50Hz | 50V | |
| Rated Current (MAX) | 0.5A | ||
| Ambient temperature Range | -25+85 | ||
| 4. PERFORMANCE | |||
| 4.1 Electrical Performance | |||
| Contact Resistance | Mate applicable FPC/FFC and measure by dry circuit, 20mV MAX, 10mA. | 30 m MAX | |
| Insulation Resistance | Mate applicable FPC/FFC and apply 500V DC between adjacent terminal or ground. | 500M MIN | |
| Dielectric Strength | Mate applicable FPC/FFC and apply 200V AC (virtual value) for 1minute between adjacent terminal or ground. | No Breakdown | |
| 4.2 Mechanical Performance | |||
| Locking and Withdrawal Force | Insert and extract applicable FFC at the speed rate of 253mm/minute. | Locking: 1.96*n (N) MAX Withdrawal: 0.49*n (N) MIN | (n=number of poles) |
| Terminal /Housing Retention Force | Pull the terminal at the speed rate of 25 3mm per minute | 3.92N MIN | |
| 4.3 Environmental Performance and Others | |||
| Repeated Insertion and Withdrawal | Insertion and withdrawal actuator up to 20 cycles at the speed rate of less than 10 cycles/minute | Contact Resistance: 60 m MAX | |
| Temperature Rise | Carrying rated current load. (UL 498) | Temperature Rise: 30 MAX | |
| Vibration | DC 1mA energizing state; vibration along XYZ three directions; Amplitude: 1.5mm; Frequency Sweep: 10-55-10Hz/minute; Duration: 2 hours in each X.Y.Z. axes | Appearance: No Damage Contact Resistance: 60 m MAX Discontinuity: 1 ms MAX. | |
| Shock | DC 1mA energizing state; 490m/s2{50G}, 3 strokes in each X.Y.Z. axes. | Appearance: No Damage Discontinuity: 1 ms MAX. | |
| Heat Resistance | Mate applicable FPC/FFC; placed in 852 air for 96 hours; then returned to room temperature for 1-2 hours. | Appearance: No Damage Contact Resistance: 60 m MAX | |
| Cold Resistance | Mate applicable FPC/FFC; placed in -402 air for 96 hours; then returned to room temperature for 1-2 hours. | Appearance: No Damage Contact Resistance: 60 m MAX | |
| Humidity | Mate applicable FPC/FFC; placed in 402, 90-95% RH air for 96 hours; measured within 0.5 hours after returning to room temperature. | Appearance: No Damage Contact Resistance: 60 m MAX Dielectric Strength: Must meet 4.1.3 Insulation Resistance: 20 M MIN | |
| Temperature Cycling | 5 cycles of: a) -553 30 minutes b) 852 30 minutes | Appearance: No Damage Contact Resistance: 60 m MAX | |
| Salt Spray | 48 4 hours exposure to a salt spray from the 51% solution at 352. After test, wash with room temperature water and dry. | Appearance: No Damage, Corrosion Contact Resistance: 60 m MAX | |
| SO2 Gas | 24 hours exposure to 505ppm SO2 gas at 402. | Contact Resistance: 60 m MAX | |
| NH3 Gas | 40 minutes exposure to NH3 gas evaporating from 28% Ammonia solution. | Appearance: No Damage Contact Resistance: 60 m MAX | |
| Solderability | Soldering Time: 20.5 sec. Soldering Temperature: 2455. 0.2 mm from terminal tip. | Solder Wetting: 95% or more | |
| Resistance to Soldering Heat | Soldering Time: 305 sec. Soldering Temperature: 2455. Performed at least 5 times. | Appearance: No Damage, Deformation | |
| 5. PRODUCT SHAPE, DIMENSIONS AND MATERIALS (Refer to the drawing) | |||
| Main body | LCP UL 94V-0 | ||
| Housing Lock | LCP UL 94V-0 | ||
| Terminal | Phosphor Bronze | Metal surface plated with tin | |
| Contact | Phosphor Bronze | Metal surface plated with tin | |
2411271641_hanxia-HX-FPC-0-5-10P-HYH2-0_C7502867.pdf
Send RFQ
Stock:
MOQ:
