0.5mm pitch flexible flat cable connector hanxia HX FPC 0.5-8P LTH2.0 designed for electronic FPC FFC
Manufacturer:
hanxia
Description:
FFC/FPC Connector 8 Position 0.5mm Pitch Single-side Contact/Vertical Surface Mount -25℃~+85℃
Category:
FFC, FPC (Flat Flexible) Connector Assemblies/FFC, FPC (Flat Flexible) Connector Assemblies
Specifications
Locking Feature:
抽屉式
Operating Temperature:
-25℃~+85℃
Number Of Contacts:
8P
Pitch:
0.5mm
Current Rating:
500mA
Voltage Rating (Max):
50V
Contact Type:
单侧触点/垂直
Mounting Type:
立贴
FFC, FCB Thickness:
0.3mm
Contact Plating:
锡
Contact Material:
磷青铜
Mfr. Part #:
HX FPC 0.5-8P LTH2.0
Package:
SMD,P=0.5mm
Model Number:
HX FPC 0.5-8P LTH2.0
Introduction
Product Overview
This specification covers the 0.5mm Pitch FPC/FFC Connectors (HX FPC 0.5-8P LTH2.0) from Shenzhen Hanxia Electronic Co., Ltd. These connectors are designed for flexible flat cable applications.
Product Attributes
- Brand: HX FPC
- Manufacturer: Shenzhen Hanxia Electronic Co., Ltd.
- Origin: China
Technical Specifications
| Item | Specification | Requirement |
| Ratings | ||
| Rated Voltage (MAX) | 50V [AC/DC(Virtual value)50Hz] | |
| Rated Current (MAX) | 0.5A | |
| Ambient temperature Range | -25+85 | |
| Performance | ||
| 4.1 Electrical Performance | ||
| Contact Resistance | Mate applicable FPC/FFC and measure by dry circuit, 20mV MAX, 10mA. | 30 m MAX |
| Insulation Resistance | Mate applicable FPC/FFC and apply 500V DC between adjacent terminal or ground. | 500M MIN |
| Dielectric Strength | Mate applicable FPC/FFC and apply 200V AC (virtual value) for 1 minute between adjacent terminal or ground. | No Breakdown |
| 4.2 Mechanical Performance | ||
| Locking and Withdrawal Force | Insert and extract applicable FFC at the speed rate of 253mm/minute. | Locking: 1.96*n (N) MAX Withdrawal: 0.49*n (N) MIN |
| Terminal /Housing Retention Force | Pull the terminal at the speed rate of 25 3mm per minute | 3.92N MIN |
| 4.3 Environmental Performance and Others | ||
| Repeated Insertion and Withdrawal | Insertion and withdrawal actuator up to 20 cycles at the speed rate of less than 10 cycles/minute | Contact Resistance: 60 m MAX |
| Temperature Rise | Carrying rated current load. (UL 498) | 30 MAX |
| Vibration | DC 1mA under energized state; Vibration along XYZ axes; Amplitude: 1.5mm; Sweep time: 10-55-10Hz/min; Duration: 2 hours in each X.Y.Z. axes | Appearance: No Damage Contact Resistance: 60 m MAX Discontinuity: 1 ms MAX. |
| Shock | DC 1mA under energized state; 490m/s2{50G}, 3 strokes in each X.Y.Z. axes. | Appearance: No Damage Discontinuity: 1 ms MAX. |
| Heat Resistance | Mate applicable FPC/FFC; Place in 852 air for 96 hours; then return to room temperature for 1-2 hours. | Appearance: No Damage Contact Resistance: 60 m MAX |
| Cold Resistance | Mate applicable FPC/FFC; Place in -402 air for 96 hours; then return to room temperature for 1-2 hours. | Appearance: No Damage Contact Resistance: 60 m MAX |
| Humidity | Mate applicable FPC/FFC; Place in 402, 90-95% RH air for 96 hours; measure within 0.5 hours after returning to room temperature. | Appearance: No Damage Contact Resistance: 60 m MAX Dielectric Strength: Must meet 4.1.3 Insulation Resistance: 20 M MIN |
| Temperature Cycling | Mate applicable FPC/FFC; 5 cycles of: a) -553 30 minutes b) 852 30 minutes | Appearance: No Damage Contact Resistance: 60 m MAX |
| Salt Spray | Mate applicable FPC/FFC; 48 4 hours exposure to a salt spray from the 51% solution at 352. Wash with room temperature water after test; then dry at room temperature. | Appearance: No Damage, Corrosion Contact Resistance: 60 m MAX |
| SO2 Gas | Mate applicable FPC/FFC; 24 hours exposure to 505ppm SO2 gas at 402. | Contact Resistance: 60 m MAX |
| NH3 Gas | Mate applicable FPC/FFC; 40 minutes exposure to NH3 gas evaporating from 28% Ammonia solution. | Appearance: No Damage Contact Resistance: 60 m MAX |
| Solder ability | Soldering Time: 20.5 sec. Soldering Temperature: 2455 0.2 mm from terminal tip | Solder Wetting: 95% or more coverage |
| Resistance to Soldering Heat | Soldering Time: 305 sec. Soldering Temperature: 2455 At least 5 times in a 2455 hot air oven. | Appearance: No Damage, Deformation |
| Product Shape, Dimensions and Materials | ||
| NAME | MATERIALS | REMARK |
| Main body | LCP UL 94V-0 | Metal surface plated tin |
| Housing Lock | LCP UL 94V-0 | |
| Terminal | Phosphor Bronze | |
| Contact | Phosphor Bronze | |
2410121337_hanxia-HX-FPC-0-5-8P-LTH2-0_C7430263.pdf
Send RFQ
Stock:
MOQ:
