HCTL HC XG 2 7AW 05 connector strip double row 2 54mm pitch tested under GB T2424 GB T5095 standards
Manufacturer:
HCTL
Description:
Connector IDC Header Through Hole, Right Angle 14 position 2.54mm
Category:
Arrays, Edge Type, Mezzanine (Board to Board)/Free Hanging, Panel Mount
Specifications
Row Spacing:
2.54mm
Operating Temperature:
-25℃~+85℃
Current Rating:
3A
Contact Plating:
金
Contact Material:
黄铜
Voltage Rating (Max):
250V
Number Of Positions Or Pins:
2x7P
Number Of PINs Per Row:
7
Number Of Rows:
2
Pitch:
2.54mm
Connector Type:
牛角扣
Mounting Type:
弯插
Mfr. Part #:
HC-XG-2*7AW-05
Package:
Through Hole,Right Angle,P=2.54mm
Model Number:
HC-XG-2*7AW-05
Introduction
Product Overview
This specification document outlines the requirements for the 2.54mm pitch XG connector, double row type. It covers product performance, test methods, and inspection requirements for these connectors, designed for various electrical applications.
Product Attributes
- Brand: HCTLDZ ()
- Origin: Shenzhen, China
- Certifications: UL94V-O, ROHS
Technical Specifications
| Item | Requirement | Test Mode |
| 1. Scope | ||
| The contents of specifications for 2.54 series connector strip including product performance, test methods and inspection requirements. | ||
| 2. Applicable Standards | ||
| GB/T2421, GB/T2423, GB/T2424, GB/T5095 | ||
| 3. Use Condition | ||
| Ambient temperature Range | -25 85 | |
| Applicable Wire Sizes | AWG #2226 | |
| Applicable PC board thickness | 1.6mm | |
| 4. Appearance and Dimension | ||
| Appearance | Product surface without defect, dirt, crack, and mechanical damage; Contact without rust plating, oxidation, and peeling. | |
| Dimension | According to drawings | |
| Exchangeable | Exchangeable with same specification products. | |
| 5. Material | ||
| Terminal Contact | Phosphor bronze, thickness 0.22mm; Brass, thickness 0.64mm | Local gold plating: 3m; Half the gold plated 2u; Half the gold plated 3u |
| Housing Plastic | PBT UL94V-O | Color: Black; Color: White |
| Wafer | Plastic | |
| Contact | Straight pin-A, Bent pin-AW | |
| 6. Electrical Performance | ||
| Rated Voltage | 250V AC/DC | |
| Rated Current | 3A AC/DC | |
| Withstand voltage | 1000M (Initial value 20m) | Apply 500V AC(rms) for 1 minute and the leakage current shall not exceed 0.5mA to the adjacent terminal and ground of the mate connectors. No breakdown or flashover. |
| Contact Resistance | 20m | A maximum voltage of 20mV and maximum current of 100mA are applied to the Mate connector. Does not include wire resistance. |
| Insulation Resistance | 1000 M | Apply 500V DC(rms) for 1 minute between adjacent contacts to measure the insulation resistance. |
| 7. Mechanical Performance | ||
| Single contact insertion force | 3.5N | The housing together with the terminal ends with wafer matched at a rate per minute to 253mm inserting force test |
| Single contact Withdrawal force | 0.39N | The terminal and the hole seat at a react per minute to 25 3mm along the write direction are pulled out from the hole in the seat capacity. |
| Terminal crimping Wire strength | AWG#22: 10N; AWG#24: 50N; AWG#26: 30N | Terminal crimping wire Axial per minute to 25 3mm rate of the pullout force. |
| Pin Retention Force | 20N | Exerts a force on the pin end at a rate per Minute 253mm until the needle exit Seat pull-out force. |
| Fixed terminals And hole seat | 15N | The housing together with the terminal ends with wafer matched at a rate per minute to 253mm inserting force test. |
| Durability | Contact Resistance 40m | Mate connectors up 30 cycles at a Maximum rate of 10 cycles per minute prior to environmental test. |
| Vibration | Current Discontinuity: 1 sec Max; Contact Resistance 40m; Appearance: No damage | Amplitude: 1.5mm p-p; Direction: X, Y, Z axes; Frequency: 10-55-10 Hz/minute; Period: 2 hours for each direction. |
| 8. Endurance Characteristics | ||
| Thermal Aging | Appearance: No damage; Contact Resistance 40m | Temperature: 852; Period: 96 hours continuously. |
| Temperature Rise | Mate connector measure the temperature rise of contact when the maximum rated current is passed. | |
| Constant Humidity | Appearance: No damage; Contact Resistance 40m; Insulation Resistance 1000m | Relative humidity: 90-95% (RH); Period: 96 hours continuously. Temperature: 402 C |
| Temperature cycling | No breakdown or flashover | One cycle consists of -553C 30min, room temp 10-15min, then 853C 30min, room temp 10-15min. Total cycle: 5 cycles. |
| Salt spray | Appearance: No damage; Contact Resistance 40m | Temperature: 35 3 C; Concentration: 51%; Period: 24H. |
| Solder ability | Soldering area: 90 % | Solder temperature: 2455C; Immersion period: 3 0.5S. |
| Resistance to soldering heat | Appearance: No damage | Wave soldering: Soldering temperature: 2605; Soldering time: 50.5S. Manual soldering: Soldering temperature: 3505; Soldering time: 30.5S. |
2311081457_HCTL-HC-XG-2-7AW-05_C19189793.pdf
Send RFQ
Stock:
MOQ:
