electrical connector HCTL HC-XG-2*10A-05 2.54mm pitch double row type with phosphor bronze contacts
Manufacturer:
HCTL
Description:
Connector IDC Header Through Hole 20 position 2.54mm
Category:
Arrays, Edge Type, Mezzanine (Board to Board)/Free Hanging, Panel Mount
Specifications
Row Spacing:
2.54mm
Operating Temperature:
-25℃~+85℃
Current Rating:
3A
Contact Plating:
金
Contact Material:
黄铜
Voltage Rating (Max):
250V
Number Of Positions Or Pins:
2x10P
Number Of PINs Per Row:
10
Number Of Rows:
2
Pitch:
2.54mm
Connector Type:
牛角扣
Mounting Type:
直插
Mfr. Part #:
HC-XG-2*10A-05
Package:
Through Hole,P=2.54mm
Model Number:
HC-XG-2*10A-05
Introduction
Product Overview
This specification covers the 2.54mm pitch XG connector double row type, including product performance, test methods, and inspection requirements. It is designed for applications requiring reliable electrical connections.
Product Attributes
- Brand: HCT ()
- Origin: Shenzhen, China
- Materials: Phosphor bronze, Brass, PBT
- Certifications: ROHS, UL94V-O
Technical Specifications
| Item | Requirement | Test Mode |
| 4. Appearance and Dimension | ||
| Appearance | Product surface without defect, dirt, crack, and mechanical damage; Contact without rust plating, oxidation, and peeling. | General Principles |
| Dimension | According to drawings | |
| Exchangeable | Exchangeable with same specification products. | |
| 3. USE CONDITION | ||
| Ambient temperature Range | -25 85 | |
| Applicable Wire Sizes | AWG #2226 | |
| Applicable PC board thickness | 1.6mm | |
| 5. Material | ||
| Terminal Contact | Phosphor bronze, Brass | 3 m / Half the gold plated 3u |
| Housing Plastic | PBT UL94V-O | Color: Black / White |
| Wafer | Plastic | Color: Black |
| 6. Electrical Performance | ||
| Rated Voltage | 250V AC/DC | |
| Rated Current | 3A AC/DC | |
| Withstand voltage | 1000 M | Apply 500V AC(rms) for 1 minute and the leakage current shall not exceed 0.5mA to the adjacent terminal and ground of the mate connectors |
| Contact Resistance | Initial value 20m | A maximum voltage of 20mV and maximum current of 100mA are applied to the Mate connector (Does not include wire resistance) |
| Insulation Resistance | More than 1000 M | Apply 500V DC(rms) for 1 minute between adjacent contacts to measure the insulation resistance |
| 7. Mechanical Performance | ||
| Single contact insertion force | 3.5N | The housing together with the terminal ends with wafer matched at a rate per minute to 253mm inserting force test |
| Single contact Withdrawal force | 0.39N | The terminal and the hole seat at a react per minute to 253mm along the write direction are pulled out from the hole in the seat capacity |
| Terminal crimping Wire strength | 10N (AWG#22), 15N (AWG#24), 20N (AWG#26) | Axial per minute to 25 3mm rate of the pullout force |
| Pin Retention Force | 30N (Pin), 50N (Wafer) | Exerts a force on the pin end at a rate per Minute 253mm until the needle exit Seat pull-out force |
| Vibration | Current Discontinuity: 1 sec Max. Contact Resistance 40m | Amplitude: 1.5mm p-p, Frequency: 10-55-10 Hz/minute, Period: 2hour for each direction (X, Y, Z axis) |
| Durability | Contact Resistance 40m | Mate connectors up 30 cycles at a Maximum rate of 10 cycles per minute prior to environmental test |
| 8. Endurance Characteristics | ||
| Thermal Aging | Contact Resistance 40m . Appearance: No damage | Temperature: 852, Period: 96 hours continuously |
| Temperature Rise | (Measured under max rated current) | Mate connector measure the temperature rise of contact when the maximum rated current is passed |
| Constant Humidity | Contact Resistance 40m . Insulation Resistance 1000m . Appearance: No damage | Relative humidity: 90-95% (RH), Period: 96 hours continuously, Temperature: 402 C |
| Temperature Cycling | No breakdown or flashover. Appearance: No damage | One cycle consists of -553C 30min, room temp 10-15min, then 853C 30min, room temp 10-15min. Total cycle: 5 cycles |
| Salt Spray | Contact Resistance 40m . Appearance: No damage | Concentration: 51%, Period: 24H, Temperature: 35 3 C |
| Solder ability | Soldering Area: 90 % | Solder temperature: 2455C, Immersion period: 3 0.5S |
| Resistance to soldering heat | Appearance: No damage | Wave soldering: Soldering temperature: 2605, Soldering time: 50.5S. Manual soldering: Soldering temperature: 3505, Soldering time: 30.5S |
2311081457_HCTL-HC-XG-2-10A-05_C19189789.pdf
Send RFQ
Stock:
MOQ:
