Electrical Connector HCTL HC-PH-6A-G PH 2.00MM Pitch Double Row Type Suitable for Various Conditions
Manufacturer:
HCTL
Description:
Connector Header 6 position 2mm Pitch 2A Through Hole -25℃~+85℃
Category:
Arrays, Edge Type, Mezzanine (Board to Board)/Headers, Male Pins
Specifications
Y-Width Of Bottom Edge On Board:
4.7mm
Reference Series:
PH
Pins Structure:
1x6P
Contact Plating:
锡
Contact Material:
黄铜;PA66
Operating Temperature:
-25℃~+85℃
Flame Retardant Rating:
UL94V-0
Pitch:
2mm
Voltage Rating (Max):
250V
Number Of PINs Per Row:
6
Number Of Rows:
1
X-Length Of Bottom Edge On Board (Spacing Line):
14mm
Z-Height Of The Board:
6mm
Row Spacing:
-
Mounting Type:
直插
Mfr. Part #:
HC-PH-6A-G
Package:
Through Hole,P=2mm
Model Number:
HC-PH-6A-G
Introduction
Product Overview
This specification details the PH 2.00MM Pitch PH Connector Double Row Type, model number HC-PH-****. It is designed for electrical connections and is suitable for use in various environmental conditions. The connector is compliant with relevant GB/T standards for electrical connectors and environmental testing.
Product Attributes
- Brand: (HCTLDZ)
- Origin: Shenzhen, China
- Material (Terminal Contact): Phosphor bronze (0.2mm thickness) with Tin plating (3-5m)
- Material (Housing Plastic): Nylon66 UL94V-0, Color: White
- Material (Pin): Brass (0.50mm thickness) with Tin plating (2.5-5m), Color: Beige
- Certifications: UL94V-0
Technical Specifications
| Item | Specification | Requirement | Test Method |
| 3. Use Condition | |||
| Ambient Temperature Range | -25 +85 | ||
| Applicable Wire Sizes | AWG #2228 | ||
| Applicable PC board thickness | 1.6mm | ||
| 4. Appearance and Dimension | |||
| Appearance | Product surface without defect, dirt, crack, and mechanical damage; Contact without rust, plating not oxides and not peeled | ||
| Dimension | According to drawings | ||
| Exchangeable | Exchangeable with same specification products | ||
| 5. Material | |||
| Terminal Contact | Phosphor bronze, 0.2mm thickness, Tin plating: 35 m | ||
| Housing Plastic | Nylon66 UL94V-0, Color: White | ||
| Pin | Brass, 0.50mm thickness, Tin plating: 2.55 m, Color: Beige | ||
| 6. Electrical Performance | |||
| Rated Voltage | 250V AC/DC | ||
| Rated Current | 2A AC/DC | ||
| Contact Resistance | Initial value 20 | 20m | Apply a maximum voltage of 20mV and maximum current of 100mA to the Mate connector (Does not include wire resistance) |
| Insulation Resistance | 1000 M | 1000 M | Apply 500V DC (rms) for 1 minute between adjacent contacts |
| Withstand voltage | No breakdown or flashover | Apply 800V AC (rms) for 1 minute and the leakage current shall not exceed 0.5mA to the adjacent terminal and ground of the mate connectors | |
| 7. Mechanical Performance | |||
| Single contact insertion force | 6N | 6N | The housing together with the terminal ends with wafer matched at a rate per minute to 253mm inserting force test |
| Single contact Withdrawal force | 0.5N | 0.5N | The terminal and the hole seat at a react per minute to 25 3mm along the write direction are pulled out from the hole in the seat capacity |
| Terminal crimping Wire strength | AWG#22: 50N, AWG#24: 30N, AWG#26: 20N, AWG#28: 13N | Axial per minute to 25 3mm rate of the pullout force | |
| Pin Retention Force | 15N | 15N | Exerts a force on the pin end at a rate per Minute 253mm until the needle exit |
| Seat pull-out force | 15N | 15N | The housing together with the terminal ends with wafer matched at a rate per minute to 253mm inserting force test |
| Durability | Contact Resistance 30m | 30m | Mate connectors up 30 cycles at a Maximum rate of 10 cycles per minute prior to environmental test |
| Vibration | Current interruption: 1 sec Max, Contact Resistance 30m | Amplitude: 1.5mm p-p, Frequency: 10-55-10Hz/minute, Duration: 2 hours for each direction (X, Y, Z axis) | |
| 8. Endurance Characteristics | |||
| Thermal Aging | Appearance: No damage, Contact Resistance 30m | 30m | Temperature: 852, Period: 96 hours continuously |
| Temperature rise | Measure the temperature rise of contact when the maximum rated current is passed | ||
| Constant Humidity | Appearance: No damage, Contact Resistance 30m , Insulation Resistance 500m | 30m , 500m | Temperature:402 C, Relative humidity: 90-95% (RH), Period: 96 hours continuously |
| Temperature cycling | Appearance: No damage, No breakdown or flashover | One cycle consists of -55 3 C 30min, 85 3C 30min, room temp 10-15min transition. Total cycle: 5 cycles | |
| Salt spray | Appearance: No damage, Contact Resistance 30m | 30m | Temperature: 353 C, Concentration: 51% NaCl solution, Period: 8 hours (post-stamping plating) or 24 hours (pre-stamping plating) |
| Solder ability | Soldering area: 90 % | 90 % | Solder temperature: 245 5C, Immersion period: 3 0.5S |
| Resistance to soldering heat | Appearance: No damage | Manual soldering: 350 5 for 3 0.5S. Wave soldering: 2305 for 50.5S. Position: 1.5mm from conductor/fixing piece end. | |
2504101957_HCTL-HC-PH-6A-G_C5342439.pdf
Send RFQ
Stock:
MOQ:
