PH series connector strip with HCTL HC-PH-3AW-G featuring brass plug pins and nylon66 UL94V0 housing
Manufacturer:
HCTL
Description:
Connector Header 3 position 2mm Pitch 2A Right Angle -25℃~+85℃
Category:
Arrays, Edge Type, Mezzanine (Board to Board)/Headers, Male Pins
Specifications
Flame Retardant Rating:
UL94V-0
Pins Structure:
1x3P
Reference Series:
PH
Contact Plating:
锡
Contact Material:
黄铜;PA66
Pitch:
2mm
Voltage Rating (Max):
250V
Number Of PINs Per Row:
3
Number Of Rows:
1
Row Spacing:
-
Operating Temperature:
-25℃~+85℃
Mounting Type:
弯插
Mfr. Part #:
HC-PH-3AW-G
Package:
Through Hole,Right Angle,P=2mm
Model Number:
HC-PH-3AW-G
Introduction
Product Overview
This specification applies to the PH series connector strip, covering product performance, test methods, and inspection requirements. It is designed for electrical connectivity with specific environmental and mechanical tolerances.
Product Attributes
- Brand: HCTLDZ ()
- Origin: Shenzhen, China
- Certifications: UL94V-O (for Nylon66/LCP)
- Applicable Wire Sizes: AWG #2228
- Applicable PC Board Thickness: 1.6mm
Technical Specifications
| Item | Part No. | Type | Material | Finish | Color | Specification |
| Terminal Contact | HC-PH - **** | PT Plug Spring | Phosphor bronze thickness 0.2mm | Tin plating: 35m | - | - |
| Housing Plastic | HC-PH - **** | P Socket | Nylon66 UL94V-0 | - | White | - |
| Wafer | HC-PH - **** | Plastic Socket | Nylon66/LCP UL94-0 | - | Beige | - |
| Contact | HC-PH - **** | Plug Pin | Brass thickness 0.50mm | Tin plating: 2.55m | - | - |
| Item | Rated Voltage | Rated Current | Requirement | Test Mode |
| Electrical Performance | 250V AC/DC | 2A AC/DC | - | - |
| Withstand Voltage | - | - | No breakdown or flashover | Apply 800V AC(rms) for 1 minute and the leakage current shall not exceed 0.5mA to the adjacent terminal and ground of the mate connectors |
| Contact Resistance | - | - | Initial value 20 | A maximum voltage of 20mV and maximum current of 100mA are applied to the Mate connector (Does not include wire resistance) |
| Insulation Resistance | - | - | 1000 M | Apply 500V DC(rms) for 1 minute between adjacent contacts to measure the insulation resistance |
| Item | Requirement | Test Mode |
| Mechanical Performance | - | - |
| Single contact insertion force | 6N | Housing together with terminal ends with wafer matched at a rate per minute to 253mm inserting force test |
| Single contact Withdrawal force | 0.5N | Terminal and hole seat matched at a rate per minute to 253mm along the wire direction, pulled out from the hole seat |
| Terminal crimping Wire strength | 15N (AWG#22) 13N (AWG#28) | Axial pullout force on crimped wire at a rate per minute of 253mm |
| Pin Retention Force | 50N (AWG#22) 30N (AWG#24) 20N (AWG#26) 15N (AWG#28) | Exerts a force on the pin end at a rate per minute of 253mm until the needle exits Seat pull-out force |
| Fixed terminals And hole seat | 15N | Terminal and hole seat fixed force |
| Durability | Contact Resistance 30m | Mate connectors up 30 cycles at a maximum rate of 10 cycles per minute prior to environmental test |
| Vibration | Current Discontinuity: Max 1 sec Contact Resistance 30m Appearance: No damage | Amplitude: 1.5mm p-p Direction: X, Y, Z axes Frequency: 10-55-10Hz/minute Period: 2 hours for each direction |
| Item | Requirement | Test Mode |
| Environmental Performance | - | - |
| Thermal Aging | Appearance: No damage Contact Resistance 30m | Temperature: 852 Period: 96 hours continuously |
| Temperature Rise | - | Mate connector measure the temperature rise of contact when the maximum rated current is passed |
| Constant Humidity | Appearance: No damage Contact Resistance 30m Insulation Resistance 500m | Temperature: 402C Relative humidity: 90-95% (RH) Period: 96 hours continuously |
| Temperature Cycling | Appearance: No damage Contact Resistance 30m Insulation Resistance 500m Withstand Voltage: No breakdown or flashover | One cycle: -553C (30min) to 853C (30min), room temp transition 10-15min Total cycle: 5 cycles |
| Salt Spray | Appearance: No damage Contact Resistance 30m | Concentration: 51% NaCl solution Temperature: 353C Period: 24 hours (pre-plated stamping) or 8 hours (post-stamping plating) |
| Solder Ability | Soldering Area: 90% | Solder temperature: 2455C Immersion period: 30.5S |
| Resistance to Soldering Heat | Appearance: No damage | Manual Soldering: Soldering time: 30.5S, Soldering pot: 3505C Wave Soldering: Soldering time: 50.5S, Soldering pot: 2305C |
2504101957_HCTL-HC-PH-3AW-G_C5342443.pdf
Send RFQ
Stock:
MOQ:
