Double row 2.54mm pitch connector strip HCTL HC-XG-2 13A 05 for secure electronic device connections
Manufacturer:
HCTL
Description:
Connector IDC Header Through Hole 26 position 2.54mm
Category:
Arrays, Edge Type, Mezzanine (Board to Board)/Free Hanging, Panel Mount
Specifications
Row Spacing:
2.54mm
Operating Temperature:
-25℃~+85℃
Current Rating:
3A
Contact Plating:
金
Contact Material:
黄铜
Voltage Rating (Max):
250V
Number Of Positions Or Pins:
2x13P
Number Of PINs Per Row:
13
Number Of Rows:
2
Pitch:
2.54mm
Connector Type:
牛角扣
Mounting Type:
直插
Mfr. Part #:
HC-XG-2*13A-05
Package:
Through Hole,P=2.54mm
Model Number:
HC-XG-2*13A-05
Introduction
Product Overview
This specification covers the 2.54mm pitch XG connector double row type, including product performance, test methods, and inspection requirements. Designed for various electronic applications, these connectors offer reliable performance and durability.
Product Attributes
- Brand: HCT ()
- Origin: Shenzhen, China
- Certifications: ROHS, UL94V-O
Technical Specifications
| Item | Requirement | Test Mode |
| 1. Scope | ||
| This specification applies to the 2.54 series connector strip, covering product performance, test methods, and inspection requirements. | ||
| 2. Applicable Standards | ||
| GB/T2421 | Electrical Connectors Environmental Testing - Part 1: General | |
| GB/T2423 | Electrical Connectors Environmental Testing | |
| GB/T2424 | Electrical Connectors Environmental Testing Guidelines | |
| GB/T5095 | Basic Testing Rules and Measurement Methods for Components of Electrical Equipment | |
| 3. Use Condition | ||
| Ambient Temperature Range | -25 +85 | |
| Applicable Wire Sizes | AWG #2226 | |
| Applicable PC Board Thickness | 1.6mm | |
| 4. Appearance and Dimension | ||
| Appearance | Product surface without defects, dirt, cracks, or mechanical damage; contacts without rust, plating oxidation, or peeling. | |
| Dimension | According to drawings | |
| Interchangeability | Exchangeable with same specification products. | |
| 5. Material | ||
| Terminal Contact | Phosphor bronze, 0.22mm thick; Brass, 0.64mm thick. Finish: Local gold plating (3m or 2m). | |
| Housing Plastic | PBT UL94V-O. Color: Black or White. | |
| Wafer | PBT UL94V-O. Color: Black. | |
| Contact Pin | Brass, 0.64mm thick. Finish: Half gold plated (3m). | |
| 6. Electrical Performance | ||
| Rated Voltage | 250V AC/DC | |
| Rated Current | 3A AC/DC | |
| Withstand Voltage | 1000V AC (rms) for 1 minute between adjacent contacts; leakage current < 0.5mA. | Apply 500V AC(rms) for 1 minute and the leakage current shall not exceed 0.5mA to the adjacent terminal and ground of the mate connectors. |
| Contact Resistance | 20m (initial value) | A maximum voltage of 20mV and maximum current of 100mA are applied to the mate connector (does not include wire resistance). |
| Insulation Resistance | 1000 M | Apply 500V DC (rms) for 1 minute between adjacent contacts to measure the insulation resistance. |
| 7. Mechanical Performance | ||
| Single Contact Insertion Force | 3.5N | Housing together with terminal ends with wafer matched at a rate of 253mm/min inserting force test. |
| Single Contact Withdrawal Force | 0.39N | Terminal and hole seat matched at a rate of 253mm/min along the wire direction, pulled out from the hole seat. |
| Terminal Crimping Wire Strength | 10N (AWG#22), 30N (AWG#24), 50N (AWG#26) | Axial pullout force at the terminal crimped wire at a rate of 253mm/min. |
| Pin Retention Force | 10N | Force exerted on the pin end at a rate of 253mm/min until the needle exits the seat. |
| Vibration | Current Discontinuity: 1 sec Max. Contact Resistance: 40m | Amplitude: 1.5mm p-p; Frequency: 10-55-10 Hz/min; Duration: 2 hours for each direction (X, Y, Z). |
| Durability | Contact Resistance: 40m | Mate connectors up 30 cycles at a maximum rate of 10 cycles/min prior to environmental test. |
| 8. Environmental Performance | ||
| Thermal Aging | Contact Resistance: 40m; Appearance: No damage | Temperature: 852; Period: 96 hours continuously. |
| Temperature Rise | Measure temperature rise of contact when maximum rated current is passed. | Connector combination condition is placed in a heating oven. |
| Constant Humidity | Contact Resistance: 40m; Insulation Resistance: 1000m; Appearance: No damage | Temperature: 402; Relative Humidity: 90-95% RH; Period: 96 hours continuously. |
| Temperature Cycling | No breakdown or flashover. | One cycle: -553 (30min) to 853 (30min), with 10-15min transition time. Total cycles: 5. |
| Salt Spray | Contact Resistance: 40m; Appearance: No damage | Temperature: 353; Concentration: 51%; Period: 24H. |
| Solder Ability | Soldering Area: 90% | Solder temperature: 2455; Immersion period: 30.5S. |
| Resistance to Soldering Heat | Appearance: No damage | Wave soldering: Pot temp 2605, Time 50.5S. Hand soldering: Pot temp 3505, Time 30.5S. |
2311081457_HCTL-HC-XG-2-13A-05_C19189790.pdf
Send RFQ
Stock:
MOQ:
