Durable PH Series Connector Strip Featuring HCTL PH-5A 2 Millimeter Pitch Double Row Type Connector
Manufacturer:
HCTL
Description:
Connector Header 5 position 2mm Pitch 2A Through Hole -25℃~+85℃
Category:
Arrays, Edge Type, Mezzanine (Board to Board)/Headers, Male Pins
Specifications
Flame Retardant Rating:
UL94V-0
Reference Series:
PH
Pins Structure:
1x5P
Contact Plating:
锡
Contact Material:
黄铜;PA66
Pitch:
2mm
Voltage Rating (Max):
250V
Number Of PINs Per Row:
5
Number Of Rows:
1
Row Spacing:
-
Mounting Type:
直插
Operating Temperature:
-25℃~+85℃
Mfr. Part #:
PH-5A
Package:
Through Hole,P=2mm
Model Number:
PH-5A
Introduction
Product Specification for Approval
This specification covers the PH series connector strip, including product performance, test methods, and inspection requirements. It is applicable to 2.00MM PITCH PH CONNECTOR DOUBLE ROW TYPE, Part No.: HC-PH - ****.
Product Attributes
- Brand: HCTLDZ ()
- Origin: Shenzhen, China
- Product Name: PH 2.0 Series Connector
- Certifications: UL94V-O (for Housing Plastic)
Technical Specifications
| Item | Requirement | Test Mode |
| 4. Appearance and Dimension | ||
| Appearance | Product surface without defect, dirt, crack, and mechanical damage; Contact without rust plating not oxides and not peeled. | General Principles |
| Dimension | According to drawings | |
| Exchangeable | Exchangeable with same specification products. | |
| 3. Use Condition | ||
| Ambient temperature Range | -25 85 | |
| Applicable Wire Sizes | AWG #2228 | |
| Applicable PC board thickness | 1.6mm | |
| 5. Material | ||
| Terminal Contact | Phosphor bronze, 0.2mm thick; Tin plating: 35 m | ROHS Material |
| Housing Plastic | Nylon66 UL94V-O; Color: White | Plastic Wafer |
| Contact Pin | Brass, 0.50mm thick; Tin plating: 2.55 m; Color: Beige | Contact |
| 6. Electrical Performance | ||
| Rated Voltage | 250V AC/DC | |
| Rated Current | 2A AC/DC | |
| Withstand voltage | 800V AC (rms) for 1 minute between adjacent contacts and ground. Leakage current must be less than 0.5mA. | Apply 800V AC(rms)for I minute and the leakage current shall not exceed 0.5mA to the adjacent terminal and ground of the mate connectors. No breakdown or flashover. |
| Contact Resistance | Initial value 20 | A maximum voltage of 20mV and maximum current of 100mA are applied to the Mate connector. Does not include wire resistance. |
| Insulation Resistance | More than 1000 M | Apply 500V DC (rms) for 1 minute between adjacent contacts to measure the insulation resistance. |
| 7. Mechanical Performance | ||
| Single contact insertion force | 6N | The housing together with the terminal ends with wafer matched at a rate per minute to 253mm inserting force test. |
| Single contact Withdrawal force | 15N | The terminal and the hole seat at a react per minute to 253mm along the write direction are pulled out from the hole in the seat capacity. |
| Terminal crimping Wire strength | AWG#22: 50N AWG#24: 30N AWG#26: 20N AWG#28: 13N | Terminal crimping wire Axial per minute to 25 3mm rate of the pullout force. |
| Pin Retention Force | 15N (per contact) | Exerts a force on the pin end at a rate per Minute 253mm until the needle exit Seat pull-out force. |
| Durability | Contact Resistance 30m | Mate connectors up 30 cycles at a Maximum rate of 10 cycles per minute prior to environmental test. |
| Vibration | Current Discontinuity: Max 1 sec; Contact Resistance 30m | Amplitude: 1.5mm p-p; Direction: X, Y, Z axes; Frequency: 10-55-10Hz/minute; Period: 2 hours for each direction. |
| 8. Endurance Characteristics (Environmental Performance) | ||
| Thermal Aging | Appearance: No damage; Contact Resistance 30m | Temperature: 852; Period: 96 hours continuously. |
| Temperature Rise | Measure temperature rise of contact when the maximum rated current is passed. | Connector combination condition is placed in the accordance with the following specifications high temperature aging test after the test and measurement of contact resistance. |
| Constant Humidity | Appearance: No damage; Contact Resistance 30m; Insulation Resistance 500m | Temperature: 402 C; Relative humidity: 90-95% (RH); Period: 96 hours continuously. |
| Temperature Cycling | Appearance: No damage; No breakdown or flashover. | -553C 30min, room temp 10-15min, then 853C 30min, room temp 10-15min. Total cycle: 5 cycles. |
| Salt Spray | Appearance: No damage; Contact Resistance 30m | Temperature: 353 C; Concentration: 51% NaCl Solution; Period: Stamping before tin plated for 24 hours (contact area), Stamping after tin plated for 8 hours. |
| Solder ability | Area of soldering: 90 % | Solder temperature: 2455C; Immersion period: 3 0.5S. |
| Resistance to soldering heat | Appearance: No damage; Contact Resistance 30m | Manual soldering: Soldering time: 30.5S; Soldering temperature: 3505; Position: 1.5mm from conductor end. Wave soldering: Soldering time: 50.5S; Soldering temperature: 2305. |
| 9. Packaging, Transport, Storage | ||
| Transport | Avoid direct rain/snow and sun exposure. Can be transported by any means. | Transport temperature: -20 +50. |
2504101957_HCTL-PH-5A_C2908626.pdf
Send RFQ
Stock:
MOQ:
