1.25mm pitch horizontal SMT connector latch JUSHUO GH125-S02DCA-00 with phosphor copper pins and ROHS compliance
Manufacturer:
JUSHUO
Description:
Connector Header 2 position 1.25mm Pitch 1A Surface Mount, Right Angle -25℃~+85℃
Category:
Headers, Male Pins/Headers, Male Pins
Specifications
Y-Width Of Bottom Edge On Board:
4.25mm
Pins Structure:
1x2P
Reference Series:
GH
Contact Plating:
锡
Contact Material:
磷青铜;LCP
Operating Temperature:
-25℃~+85℃
Flame Retardant Rating:
UL94V-0
Pitch:
1.25mm
Voltage Rating (Max):
50V
Number Of PINs Per Row:
2
Number Of Rows:
1
X-Length Of Bottom Edge On Board (Spacing Line):
5.8mm
Z-Height Of The Board:
4.05mm
Mounting Type:
卧贴
Row Spacing:
-
Mfr. Part #:
GH125-S02DCA-00
Package:
SMD,P=1.25mm,Surface Mount,Right Angle
Model Number:
GH125-S02DCA-00
Introduction
Product Overview
This product acknowledgment document details the specifications for the 1.25mm pitch horizontal SMT connector with latch, model GH125-S**DCA-00. It covers standard ratings, packaging, transport, storage, component materials, appearance, electrical characteristics, environmental characteristics, and mechanical properties, ensuring compliance with ROHS environmental requirements.
Product Attributes
- Brand: (SHENZHEN JUSHUO ELECTRONIC CO.,LTD)
- Product Name: 1.25mm() / 1.25mm
- Product Model: GH125-S**DCA-00
- Origin: Shenzhen, China
- Certifications: ROHS environmental requirements
Technical Specifications
| Item | Specifications/Requirements | Test Method |
| Standard Rating | ||
| Rated Voltage | 50V | |
| Rated Current | 1.0A AC/DC | |
| Operating Temperature Range | -2585 | |
| Operating Humidity Range | Relative humidity is below 90% | |
| Component Materials | ||
| Base | LCP E130i | |
| Pin | Phosphor copper | |
| Stator | Phosphor copper | |
| Electrical Characteristics | ||
| Contact Resistance | 20m Max | Plug in the connector and test it with a contact resistance meter to measure both terminals of the connector Form a closed loop between. |
| Insulation Resistance | 500M Min | Plug in the connector and apply 100V DC voltage between the adjacent contacts and between the contacts and the enclosure for 1 minute. |
| Withstand Voltage | No breakdown and flashover | Plug in the connector and apply 500V AC voltage between the adjacent contacts and between the contacts and the enclosure for 1 minute. |
| Environmental Characteristics | ||
| Heating Test (85, 96H) | Appearance: no damage; Contact resistance: 60m Max | Put the plug connector in the environment of +852 for 96H, take it out and put it in the normal environment for 1~2H before testing. |
| Cold Tolerance Test (-25, 96H) | Appearance: no damage; Contact resistance: 60m Max | The plug connector was placed in the environment with the temperature of -252 for 96H, and was taken out and placed in the normal environment for 1~2H before being tested. |
| Moisture Resistance Test (40, 90~96% RH, 96H) | Appearance: no damage; Insulation resistance: 60M min; Withstand voltage: 250V AC/minute MIN | Place the plug connector in an environment with a temperature of 402 and relative humidity of 90~96%.Last for 96H, after the test, take it out and put it in the normal environment for 1~2H before the test. |
| Temperature Cycle (-25 to +85, 5 cycles) | Appearance: no abnormal; Contact resistance: 60m Max | Put the test samples into the high and low temperature test chamber, and adjust the temperature according to the following steps: A. Place for 30 minutes under the constant temperature of -253 B. Place at room temperature for 1 hour C. Place for 30 minutes at a constant temperature of +853 D. Place at room temperature for 1 hour From a to d is a cycle period, a total of 5 cycles are carried out, and 2H is recovered in the normal environmentCheck later. |
| Salt Spray Test (5% NaCl, 24H) | Appearance: no damage or corrosion (hardware should not expose the bottom metal of serious corrosion: use pre-plating The blanking surface is allowed to have a slight corrosion that does not affect its performance.); Contact resistance: 60m Max | The test sample was suspended from the top of the test box, and the concentration of (51)% Sodium Chloride Solution was continuously sprayed with 24H. After testing, the surface precipitates were lightly washed with flowing steaming water, then the 1~2H was rechecked at normal temperature. |
| Weldability | Tin area above 95% | Dip the welded part of the test sample into 2605 tin solution and hold 2.50.5 seconds. |
| Soldering Resistance | 1. Plastic parts shall be free from obvious deformation, damage and blistering. 2. The electrical characteristics must meet the specifications. | Place the connector on the PCB, and then reflow the product through 260 5 Or wave soldering for 5 1s. |
| Mechanical Properties | ||
| Pin Fixing Force | Single pin 5N min | Fix the pin holder on the drawing machine and apply force on the front end of the pin at a rate of 253mm per minute until the pin is withdrawn from the pin holder. |
| Terminal Retention in Plastic Parts | Single terminal: 7N min | The terminal shall be matched with the hole seat, and at the rate of 253mm per minute along the conductor direction, the force that the terminal is pulled out of the socket. |
| Mechanical Life | Contact resistance: 80m Max | Under no power on state, plug and unplug 30 times at the speed of 10 times / min. |
| Terminal Crimp Wire Strength | 26AWG wire: 17.8N; 28AWG wire: 8.9N; 30AWG wire: 4.4N; 32AWG wire: 2.2N | The terminals are pressed into wire at 253mm per minute The axial pullout rate of 26AWG wire |
| Insertion/Pull-out Force | Insertion force: 2N(Per pin); Pull-out force: 0.3N(Per pin) | (1) Fit the hole seat and the terminal, and conduct the insertion and removal test on the same axis with the needle seat. Remove the lock of the hole seat (test speed: 20 5mm) minute during the test (2) Performance requirements: |
2410121633_JUSHUO-GH125-S02DCA-00_C2886765.pdf
Related Products
Durable Electrical Connector JUSHUO AFC10-S06PCC-00 Featuring PCB Layout for Electronic Applications
Connector Header 6 position 1mm Pitch
Industrial electronic connector JUSHUO AFC20-S04ACC-00 part of XFC series designed for connectivity
Connector Header 4 position 2mm Pitch
Durable electronic 1.0mm pitch horizontal SMT connector JUSHUO AFC10-S02QCA-00 with ROHS compliance
Connector Header 2 position 1mm Pitch 500mA Surface Mount, Right Angle -25℃~+85℃
1.5mm Pitch Horizontal SMT Connector JUSHUO AFC15-S08DCA-00 Electronic Component for Circuit Boards
Connector Header 8 position 1.5mm Pitch 1A Surface Mount, Right Angle -20℃~+85℃
Complete PCB Layout Design and Documentation Including JUSHUO AFC10-S05PCC-00 Model for Circuit Board
Connector Header 5 position 1mm Pitch
Electronic 2.0mm Horizontal SMT Socket Connector with Latch JUSHUO GH200-S05ACA-00 Solution
Connector Header 5 position 2mm Pitch 2A Surface Mount, Right Angle -25℃~+85℃
Compact and versatile JUSHUO AFC10-S11QCC-00 connector unit optimized for electronic device assembly
Connector Header 11 position 1mm Pitch
Precision engineered JUSHUO AFC12-S16DCC-00 connector suitable for demanding electronic environments
Connector Header 16 position 1.25mm Pitch
Wafer patch socket connector 125mm pitch JUSHUO 1.25T-8PWT ideal for FPC FFC mating and connection
Connector Header 8 position 1.25mm Pitch
connection solution JUSHUO AFC20-S10ACC-00 connector for electronic and industrial automation equipment
Connector Header 10 position 2mm Pitch
Send RFQ
Stock:
MOQ:
