Horizontal SMT connector latch 1.25mm pitch JUSHUO GH125-S15DCA-00 component technical specifications
Manufacturer:
JUSHUO
Description:
Connector Header 15 position 1.25mm Pitch 1A Surface Mount, Right Angle -25℃~+85℃
Category:
Headers, Male Pins/Headers, Male Pins
Specifications
Y-Width Of Bottom Edge On Board:
4.25mm
Pins Structure:
1x15P
Reference Series:
GH
Contact Plating:
锡
Contact Material:
磷青铜;LCP
Operating Temperature:
-25℃~+85℃
Flame Retardant Rating:
UL94V-0
Pitch:
1.25mm
Voltage Rating (Max):
50V
Number Of PINs Per Row:
15
Number Of Rows:
1
X-Length Of Bottom Edge On Board (Spacing Line):
22.05mm
Z-Height Of The Board:
4.05mm
Mounting Type:
卧贴
Row Spacing:
-
Mfr. Part #:
GH125-S15DCA-00
Package:
SMD,P=1.25mm,Surface Mount,Right Angle
Model Number:
GH125-S15DCA-00
Introduction
Product Overview
This product acknowledgment document details the specifications for the 1.25mm pitch horizontal SMT connector with latch, model GH125-S**DCA-00. It covers standard ratings, packaging, transportation, storage, component materials, appearance, electrical characteristics, environmental characteristics, and mechanical properties. This specification is applicable to the GH series products.
Product Attributes
- Brand: SHENZHEN JUSHUO ELECTRONIC CO.,LTD
- Origin: Shenzhen, China
- Certifications: ROHS environmental protection requirements
Technical Specifications
| Item | Specifications | Test Method | Performance Requirements |
| 4. Standard Rating | |||
| Rated voltage | 50V | ||
| Rated current | 1.0A AC/DC | ||
| Operating temperature range | -2585 | ||
| Operating humidity range | Relative humidity is below 90% | ||
| 7. Component Name/Material | |||
| Part name | Model | Material | |
| Base | GH | LCP E130i | |
| Pin | GH | Phosphor copper | |
| Stator | GH | Phosphor copper | |
| 9. Electrical Characteristics | |||
| Contact resistance | Plug in the connector and test with a contact resistance meter. | 20m Max | |
| Insulation resistance | Apply 100V DC voltage between adjacent contacts and between contacts and enclosure for 1 minute. | 500M Min | |
| Withstand voltage | Apply 500V AC voltage between adjacent contacts and between contacts and enclosure for 1 minute. | No breakdown and flashover | |
| 10. Environmental Characteristics | |||
| Heating test | Appearance: no damage. Contact resistance: 60m Max. | Place plug connector in +852 for 96H, then in normal environment for 1-2H. | |
| Cold tolerance test | Appearance: no damage. Contact resistance: 60m Max. | Place plug connector in -252 for 96H, then in normal environment for 1-2H. | |
| Moisture resistance test | Appearance: no damage. Insulation resistance: 60M Min. Withstand voltage: 250V AC/minute MIN. | Place plug connector in 402, 90-96% RH for 96H, then in normal environment for 1-2H. | |
| Temperature cycle | Appearance: no abnormality. Contact resistance: 60m Max. | 5 cycles of -253 (30min), room temp (1H), +853 (30min), room temp (1H), then recover 2H. | |
| Salt Spray Test | Appearance: no damage or corrosion. Contact resistance: 60m Max. | Continuous spray with 51% NaCl solution for 24H, then rinse with distilled water and recover 1-2H. | |
| Weldability | Tin area above 95% | Dip in 2605 tin solution for 2.50.5 seconds. | |
| Soldering resistance | 1. Plastic parts: no obvious deformation, damage, or blistering. 2. Electrical characteristics must meet specifications. | Reflow or wave soldering at 2605 for 51S. | |
| 11. Mechanical Properties | |||
| Pin fixing force | Single pin 5N min | Apply force at front end of pin at 253mm/min rate until pin withdraws. | |
| Terminal retention in plastic parts | Single terminal: 7N min | Pull terminal from socket at 253mm/min rate along wire direction. | |
| Mechanical life | Contact resistance: 80m Max | Plug and unplug 30 times at 10 times/min speed without power. | |
| Terminal crimp wire strength | 26AWG wire 17.8N | Axial pullout force at 253mm/min rate. | |
| Terminal crimp wire strength | 28AWG wire 8.9N | Axial pullout force at 253mm/min rate. | |
| Terminal crimp wire strength | 30AWG wire 4.4N | Axial pullout force at 253mm/min rate. | |
| Terminal crimp wire strength | 32AWG wire 2.2N | Axial pullout force at 253mm/min rate. | |
| Insertion/Pull-out force | Insertion force 2N(Per pin) Pullout force 0.3N(Per pin) | Fit hole seat and terminal, insert/remove on same axis. Remove lock. Test speed: 205mm/min. | |
2410121633_JUSHUO-GH125-S15DCA-00_C2886778.pdf
Related Products
Durable Electrical Connector JUSHUO AFC10-S06PCC-00 Featuring PCB Layout for Electronic Applications
Connector Header 6 position 1mm Pitch
Industrial electronic connector JUSHUO AFC20-S04ACC-00 part of XFC series designed for connectivity
Connector Header 4 position 2mm Pitch
Durable electronic 1.0mm pitch horizontal SMT connector JUSHUO AFC10-S02QCA-00 with ROHS compliance
Connector Header 2 position 1mm Pitch 500mA Surface Mount, Right Angle -25℃~+85℃
1.5mm Pitch Horizontal SMT Connector JUSHUO AFC15-S08DCA-00 Electronic Component for Circuit Boards
Connector Header 8 position 1.5mm Pitch 1A Surface Mount, Right Angle -20℃~+85℃
Complete PCB Layout Design and Documentation Including JUSHUO AFC10-S05PCC-00 Model for Circuit Board
Connector Header 5 position 1mm Pitch
Electronic 2.0mm Horizontal SMT Socket Connector with Latch JUSHUO GH200-S05ACA-00 Solution
Connector Header 5 position 2mm Pitch 2A Surface Mount, Right Angle -25℃~+85℃
Compact and versatile JUSHUO AFC10-S11QCC-00 connector unit optimized for electronic device assembly
Connector Header 11 position 1mm Pitch
Precision engineered JUSHUO AFC12-S16DCC-00 connector suitable for demanding electronic environments
Connector Header 16 position 1.25mm Pitch
Wafer patch socket connector 125mm pitch JUSHUO 1.25T-8PWT ideal for FPC FFC mating and connection
Connector Header 8 position 1.25mm Pitch
connection solution JUSHUO AFC20-S10ACC-00 connector for electronic and industrial automation equipment
Connector Header 10 position 2mm Pitch
Send RFQ
Stock:
MOQ:
