Wafer Patch Socket Connector 1.0mm Pitch JUSHUO AFC10-S04QCA-00 for FPC FFC Applications
Manufacturer:
JUSHUO
Description:
Connector Header 4 position 1mm Pitch 500mA Surface Mount, Right Angle -25℃~+85℃
Category:
Headers, Male Pins/Headers, Male Pins
Specifications
Reference Series:
SH
Pins Structure:
1x4P
Contact Plating:
锡
Contact Material:
磷青铜;LCP
Operating Temperature:
-25℃~+85℃
Flame Retardant Rating:
UL94V-0
Pitch:
1mm
Voltage Rating (Max):
50V
Number Of PINs Per Row:
4
Number Of Rows:
1
X-Length Of Bottom Edge On Board (Spacing Line):
6.3mm
Z-Height Of The Board:
3.14mm
Mounting Type:
卧贴
Row Spacing:
-
Mfr. Part #:
AFC10-S04QCA-00
Package:
SMD,P=1mm,Surface Mount,Right Angle
Model Number:
AFC10-S04QCA-00
Introduction
Product Specification
This specification covers the 1.0mm Pitch wafer patch socket connectors. It is designed for FPC/FFC applications and meets ROHS environmental requirements.
Product Attributes
- Brand: JUSHUO ()
- Origin: Shenzhen, China
- Certifications: ROHS
Technical Specifications
| Item | Specification | Requirement |
| 2. Product Name and Part Number | ||
| Product Name | WAFER | |
| Part Number | AFC10-S**QCA-00 | |
| 3. Ratings | ||
| Rated Voltage (MAX) | 50V | |
| Rated Current (MAX) | 0.5A [AC/DC (Virtual value) 50Hz] | |
| Ambient Temperature Range | -45 +85 | (Including terminal temperature rise) |
| 4. Component Specification | ||
| Base Material | LCP E130i | |
| Pin Material | Phosphor copper | |
| Stator Material | Phosphor copper | |
| 6. Performance | ||
| 6.1 Electrical Performance | ||
| Item | Test Condition | Requirement |
| Contact Resistance | Plug in the connector and test with a contact resistance meter. Measure between two terminals of the connector to form a closed loop. | 20 m MAX |
| Insulation Resistance | Plug in the connector and apply 500V DC voltage between adjacent contacts and between contacts and enclosure for 1 minute. | 500M MIN |
| Dielectric Strength | Mate applicable FPC/FFC and apply 200V AC (virtual value) for 1 minute between adjacent terminals or ground. | No Breakdown |
| 6.2 Mechanical Performance | ||
| Item | Test Condition | Requirement |
| Pin fixing force | Fix the pin holder on the drawing machine and apply force on the front end of the pin at a rate of 253mm per minute until the pin is withdrawn from the pin holder. | Single pin: 5N MIN |
| Terminal Retention in Plastic parts | The terminal shall be matched with the hole seat, and at the rate of 253mm per minute along the conductor direction, the force that the terminal is pulled out of the socket. | Single terminal: 5N MIN |
| 6.3 Environmental Performance | ||
| Item | Test Condition | Requirement |
| Heat Resistance | Place the connector in an environment of +852 for 96H, then remove and test after 1-2H in normal environment. | Contact Resistance: 30 m MAX; Appearance: No Damage |
| Cold Resistance | Place the connector in an environment of -452 for 96H, then remove and test after 1-2H in normal environment. | Contact Resistance: 30 m MAX; Appearance: No Damage |
| Humidity | Place the connector in an environment of 452, relative humidity 90-96% for 96H. After testing, remove and test after 1-2H in normal environment. | Contact Resistance: 30 M MIN; Dielectric Strength: 500V AC/MIN; Appearance: No Damage |
| Temperature Cycling | Test samples are placed in high and low temperature test chambers and the temperature is adjusted according to the following steps: a) Maintain at -453 for 30 minutes; b) Maintain at normal temperature for 1H; c) Maintain at 853 for 30 minutes; d) Maintain at normal temperature for 1H; a to d is one cycle, a total of 5 cycles. After recovery in a normal environment for 2H, inspect. | Contact Resistance: 60 m MAX; Appearance: No Damage |
| Salt Spray Resistance | Test samples are suspended from the top of the test chamber; sprayed with 5 1% salt water at 452 for 48 hours; washed with normal temperature water after testing; then dried at room temperature. | Contact Resistance: 30 m MAX; Appearance: No Damage, Corrosion |
| Solder Ability | Immerse the sample's welding surface in a 2455 tin bath for 2.50.5 sec. | Tin Area: Above 95% |
| Soldering Resistance | Place the connector on a PCB board and immerse in a 2605 tin bath for 50.5 sec. | Tin Area: Above 95%; Appearance: No Damage, Deformation |
| 7. Appearance and Size | ||
| Item | Specification | Requirement |
| Appearance | The surface of plastic parts shall be free of obvious scars, mottled, cracked, burr, flash, lack of material and deformation affecting the use; the surface of metal parts shall be smooth and clean, no rust, oxidation, peeling, blackening and obvious mechanical damage. | |
| Size | Refer to engineering drawing | |
2504101957_JUSHUO-AFC10-S04QCA-00_C2764183.pdf
Related Products
Durable Electrical Connector JUSHUO AFC10-S06PCC-00 Featuring PCB Layout for Electronic Applications
Connector Header 6 position 1mm Pitch
Industrial electronic connector JUSHUO AFC20-S04ACC-00 part of XFC series designed for connectivity
Connector Header 4 position 2mm Pitch
Durable electronic 1.0mm pitch horizontal SMT connector JUSHUO AFC10-S02QCA-00 with ROHS compliance
Connector Header 2 position 1mm Pitch 500mA Surface Mount, Right Angle -25℃~+85℃
1.5mm Pitch Horizontal SMT Connector JUSHUO AFC15-S08DCA-00 Electronic Component for Circuit Boards
Connector Header 8 position 1.5mm Pitch 1A Surface Mount, Right Angle -20℃~+85℃
Complete PCB Layout Design and Documentation Including JUSHUO AFC10-S05PCC-00 Model for Circuit Board
Connector Header 5 position 1mm Pitch
Electronic 2.0mm Horizontal SMT Socket Connector with Latch JUSHUO GH200-S05ACA-00 Solution
Connector Header 5 position 2mm Pitch 2A Surface Mount, Right Angle -25℃~+85℃
Compact and versatile JUSHUO AFC10-S11QCC-00 connector unit optimized for electronic device assembly
Connector Header 11 position 1mm Pitch
Precision engineered JUSHUO AFC12-S16DCC-00 connector suitable for demanding electronic environments
Connector Header 16 position 1.25mm Pitch
Wafer patch socket connector 125mm pitch JUSHUO 1.25T-8PWT ideal for FPC FFC mating and connection
Connector Header 8 position 1.25mm Pitch
connection solution JUSHUO AFC20-S10ACC-00 connector for electronic and industrial automation equipment
Connector Header 10 position 2mm Pitch
Send RFQ
Stock:
MOQ:
