1.25mm Pitch Connector with Latch JUSHUO GH125-S11DCA-00 Horizontal Surface Mount Electrical Component
Manufacturer:
JUSHUO
Description:
Connector Header 11 position 1.25mm Pitch 1A Surface Mount, Right Angle -25℃~+85℃
Category:
Headers, Male Pins/Headers, Male Pins
Specifications
Y-Width Of Bottom Edge On Board:
4.25mm
Pins Structure:
1x11P
Reference Series:
GH
Contact Plating:
锡
Contact Material:
磷青铜;LCP
Operating Temperature:
-25℃~+85℃
Flame Retardant Rating:
UL94V-0
Pitch:
1.25mm
Voltage Rating (Max):
50V
Number Of PINs Per Row:
11
Number Of Rows:
1
X-Length Of Bottom Edge On Board (Spacing Line):
17.05mm
Z-Height Of The Board:
4.05mm
Mounting Type:
卧贴
Row Spacing:
-
Mfr. Part #:
GH125-S11DCA-00
Package:
SMD,P=1.25mm,Surface Mount,Right Angle
Model Number:
GH125-S11DCA-00
Introduction
Product Acknowledgement
Customer: SHENZHEN JUSHUO ELECTRONIC CO.,LTD
Product Name: 1.25mm(
Material Number: GH125-S**DCA-00 (**PIN)
Version No: 1 1 version
Page: 2 of 8
Product Overview
This specification is applicable to GH series products, specifically the 1.25mm pitch horizontal surface mount connector with latch (GH125-S**DCA-00). It details the standard ratings, environmental protection, packaging, transportation, storage, component materials, appearance, electrical characteristics, environmental characteristics, and mechanical properties of the product.
Product Attributes
- Brand: JUSHUO ELECTRONIC ()
- Origin: Shenzhen, China
- Certifications: ROHS environmental protection requirements
Technical Specifications
| Item | Specification | Test Method | Performance Requirement |
|---|---|---|---|
| Standard Rating | |||
| Rated Voltage | 50V | ||
| Rated Current | 1.0A AC/DC | ||
| Operating Temperature Range | -2585 | ||
| Operating Humidity Range | Relative humidity is below 90% | ||
| Component Materials | |||
| Part Name | Model | Material | |
| Base | GH | LCP E130i | |
| Pin | GH | Phosphor copper | |
| Stator | GH | Phosphor copper | |
| Electrical Characteristics | |||
| Contact Resistance | Plug in the connector and test it with a contact resistance meter to measure both terminals of the connector. Form a closed loop between. | 20m Max | |
| Insulation Resistance | Plug in the connector and apply 100V DC voltage between the adjacent contacts and between the contacts and the enclosure for 1 minute. | 500M Min | |
| Withstand Voltage | Plug in the connector and apply 500V AC voltage between the adjacent contacts and between the contacts and the enclosure for 1 minute. | No breakdown and flashover | |
| Environmental Characteristics | |||
| Heating Test | Put the plug connector in the environment of +852 for 96H, take it out and put it in the normal environment for 1~2H before testing. | Appearance: no damage. Contact resistance: 60m Max | |
| Cold Tolerance Test | The plug connector was placed in the environment with the temperature of -252 for 96H, and was taken out and placed in the normal environment for 1~2H before being tested. | Appearance: no damage. Contact resistance: 60m Max | |
| Moisture Resistance Test | Place the plug connector in an environment with a temperature of 402 and relative humidity of 90~96%. Last for 96H, after the test, take it out and put it in the normal environment for 1~2H before the test. | Appearance: no damage. Insulation resistance: 60M min. Withstand voltage: 250V AC/minute MIN | |
| Temperature Cycle | Put the test samples into the high and low temperature test chamber, and adjust the temperature according to the following steps: A. Place for 30 minutes under the constant temperature of -253 B. Place at room temperature for 1 hour C. Place for 30 minutes at a constant temperature of +853 D. Place at room temperature for 1 hour From a to d is a cycle period, a total of 5 cycles are carried out, and 2H is recovered in the normal environmentCheck later. | Appearance: no abnormalities. Contact resistance: 60m Max | |
| Salt Spray Test | The test sample was suspended from the top of the test box, and the concentration of (51)% Sodium Chloride Solution was continuously sprayed with 24H. After testing, the surface precipitates were lightly washed with flowing steaming water, then the 1~2H was rechecked at normal temperature. | Appearance: no damage or corrosion (hardware should not expose the bottom metal of serious corrosion: use pre-plating. The blanking surface is allowed to have a slight corrosion that does not affect its performance. Contact resistance: 60m Max | |
| Weldability | Dip the welded part of the test sample into 2605 tin solution and hold 2.50.5 seconds. | Tin area above 95% | |
| Soldering Resistance | Place the connector on the PCB, and then reflow the product through 2605 or wave soldering for 51s. | 1. Plastic parts shall be free from obvious deformation, damage and blistering. 2. The electrical characteristics must meet the specifications. | |
| Mechanical Properties | |||
| Pin Fixing Force | Fix the pin holder on the drawing machine and apply force on the front end of the pin at a rate of 253mm per minute until the pin is withdrawn from the pin holder. | Single pin 5N min | |
| Terminal Retention in Plastic Parts | The terminal shall be matched with the hole seat, and at the rate of 253mm per minute along the conductor direction, the force that the terminal is pulled out of the socket. | Single terminal: 7N min | |
| Mechanical Life | Under no power on state, plug and unplug 30 times at the speed of 10 times / min. | Contact resistance: 80m Max | |
| Terminal Crimp Wire Strength | The terminals are pressed into wire at 253mm per minute The axial pullout rate of | 26AWG wire: 17.8N 28AWG wire: 8.9N 30AWG wire: 4.4N 32AWG wire: 2.2N | |
| Insertion/Pullout Force | (1) Fit the hole seat and the terminal, and conduct the insertion and removal test on the same axis with the needle seat. Remove the lock of the hole seat (test speed: 20 5mm)/minute during the test | Insertion force: 2N(Per pin) Pullout force: 0.3N(Per pin) | |
2410121633_JUSHUO-GH125-S11DCA-00_C2886774.pdf
Related Products
Durable Electrical Connector JUSHUO AFC10-S06PCC-00 Featuring PCB Layout for Electronic Applications
Connector Header 6 position 1mm Pitch
Industrial electronic connector JUSHUO AFC20-S04ACC-00 part of XFC series designed for connectivity
Connector Header 4 position 2mm Pitch
Durable electronic 1.0mm pitch horizontal SMT connector JUSHUO AFC10-S02QCA-00 with ROHS compliance
Connector Header 2 position 1mm Pitch 500mA Surface Mount, Right Angle -25℃~+85℃
1.5mm Pitch Horizontal SMT Connector JUSHUO AFC15-S08DCA-00 Electronic Component for Circuit Boards
Connector Header 8 position 1.5mm Pitch 1A Surface Mount, Right Angle -20℃~+85℃
Complete PCB Layout Design and Documentation Including JUSHUO AFC10-S05PCC-00 Model for Circuit Board
Connector Header 5 position 1mm Pitch
Electronic 2.0mm Horizontal SMT Socket Connector with Latch JUSHUO GH200-S05ACA-00 Solution
Connector Header 5 position 2mm Pitch 2A Surface Mount, Right Angle -25℃~+85℃
Compact and versatile JUSHUO AFC10-S11QCC-00 connector unit optimized for electronic device assembly
Connector Header 11 position 1mm Pitch
Precision engineered JUSHUO AFC12-S16DCC-00 connector suitable for demanding electronic environments
Connector Header 16 position 1.25mm Pitch
Wafer patch socket connector 125mm pitch JUSHUO 1.25T-8PWT ideal for FPC FFC mating and connection
Connector Header 8 position 1.25mm Pitch
connection solution JUSHUO AFC20-S10ACC-00 connector for electronic and industrial automation equipment
Connector Header 10 position 2mm Pitch
Send RFQ
Stock:
MOQ:
