Compact 1.0mm Pitch Vertical SMT Connector JUSHUO AFC10-S02PCA-00 with ROHS Environmental Compliance
Manufacturer:
JUSHUO
Description:
Connector Header 2 position 1mm Pitch 500mA Surface Mount,Vertical -25℃~+85℃
Category:
Headers, Male Pins/Headers, Male Pins
Specifications
Y-Width Of Bottom Edge On Board:
3.76mm
Pins Structure:
1x2P
Reference Series:
SH
Contact Plating:
锡
Contact Material:
磷青铜;LCP
Operating Temperature:
-25℃~+85℃
Flame Retardant Rating:
UL94V-0
Pitch:
1mm
Voltage Rating (Max):
50V
Number Of PINs Per Row:
2
Number Of Rows:
1
X-Length Of Bottom Edge On Board (Spacing Line):
4.3mm
Z-Height Of The Board:
4.4mm
Row Spacing:
-
Mounting Type:
立贴
Mfr. Part #:
AFC10-S02PCA-00
Package:
SMD,P=1mm
Model Number:
AFC10-S02PCA-00
Introduction
Product Overview
This product acknowledgment document details the 1.0mm pitch vertical SMT connector, model AFC10-S**PCA-00. It outlines the product's specifications, electrical and environmental characteristics, and mechanical properties, intended for customer confirmation.
Product Attributes
- Brand: SHENZHEN JUSHUO ELECTRONIC CO.,LTD
- Product Name: 1.0mm
- Product Model: AFC10-S**PCA-00
- Version: 1 1 version
- Material: Base: LCP E130i, Reed: Phosphor copper, Stator: Phosphor copper
- Environmental Compliance: ROHS
Technical Specifications
| Item | Specifications | Test Method | Performance Requirement |
| Standard Rating | |||
| Rated Voltage | 50V | ||
| Rated Current | 0.5A AC/DC | ||
| Operating Temperature Range | -25+105 | ||
| Operating Humidity Range | Relative humidity is below 90% | ||
| Electrical Characteristics | |||
| Contact Resistance | Plug in the connector and test it with a contact resistance meter to measure both terminals of the connector Form a closed loop between. | 20m Max | |
| Insulation Resistance | Plug in the connector and apply 500V DC voltage between the adjacent contacts and between the contacts and the enclosure for 1 minute. | 100M Min | |
| Withstand Voltage | Plug in the connector and apply 500V AC voltage between the adjacent contacts and between the contacts and the enclosure for 1 minute. | No breakdown and flashover | |
| Environmental Characteristics | |||
| Heating Test | Put the plug connector in the environment of +1052 for 96H, take it out and put it in the normal environment for 1~2H before testing. | Appearance: appearance without damage; Contact resistance: 30m Max | |
| Cold Tolerance Test | The plug connector was placed in the environment with the temperature of -252 for 96H, and was taken out and placed in the normal environment for 1~2H before being tested. | Appearance: appearance without damage; Contact resistance: 30m Max | |
| Moisture Resistance Test | Place the plug connector in an environment with a temperature of 402 and relative humidity of 90 96%.Last for 96H, after the test, take it out and put it in the normal environment for 1~2H before the test. | Appearance: appearance without damage; Insulation resistance: 50M min; Withstand voltage: 200VAC/min te MIN | |
| Temperature Cycle | Put the test samples into the high and low temperature test chamber, and adjust the temperature according to the following steps: A. Place for 30 minutes under the constant temperature of -253 B. Place at room temperature for 1 hour C. Place for 30 minutes at a constant temperature of +1053 D. Place at room temperature for 1 hour From a to d is a cycle period, a total of 5 cycles are carried out, and 2H is recovered in the normal environment Check later. | Appearance: no abnormalities; Contact resistance: 30m Max | |
| Salt Spray Test | Suspend the test sample from the top of the test chamber with a concentration of (5 1)% of Sodium Chloride Solution, continuous spray 24H, after test, with flowing steaming water gently. Wash away the precipitates on the surface, recover for 1 ~ 2H under normal temperature, and then check and measure. | Appearance: no damage or corrosion (Hardware should have no exposed bottom metal Severe corrosion: use pre-plating well The profile, the blanking surface is allowed to have Slight corrosion that does not affect its performance.); Contact resistance: 30m Max | |
| Weldability | Dip the welded part of the test sample into 2355 tin solution and hold 2.50.5 seconds. | Tin area above 95% | |
| Soldering Resistance | Place the connector on the PCB, and then reflow the product through 260 5 Or wave soldering for 51s. | 1. Plastic parts shall be free from obvious deformation, damage and blistering. 2. The electrical characteristics must meet the specifications. | |
| Mechanical Properties | |||
| Pin Fixing Force | Fix the pin holder on the drawing machine and apply force on the front end of the pin at a rate of 253mm per minute until the pin is withdrawn from the pin holder. | Single pin 7N min | |
| Terminal Retention in Plastic Parts | The terminal shall be matched with the hole seat, and at the rate of 253mm per minute along the conductor direction, the force that the terminal is pulled out of the socket. | Single terminal: 5N min | |
| Mechanical Life | Under no power on state, plug and unplug 50 times at the speed of 10 times / min. | Contact resistance: 30m Max | |
| Insert Force/Draw Force | (1) the hole seat and the terminal should be well matched, and the pin seat should be inserted on the same axis for the test. The hole seat should be locked during the test Remove (test speed: 205mm/minute (2) Performance requirements: PIN Position Insert (N) Pull out (N) PIN Position Insert (N) Pull out (N) 1 3.00 0.50 9 29.00 5.50 2 8.00 2.00 10 32.00 6.00 3 11.00 2.50 11 35.00 6.50 4 14.00 3.00 12 38.00 7.00 5 17.00 3.50 13 41.00 7.50 6 20.00 4.00 14 44.00 8.00 7 23.00 4.50 15 47.00 8.50 8 26.00 5.00 16 50.00 9.00 | ||
2410121633_JUSHUO-AFC10-S02PCA-00_C2764196.pdf
Related Products
Durable Electrical Connector JUSHUO AFC10-S06PCC-00 Featuring PCB Layout for Electronic Applications
Connector Header 6 position 1mm Pitch
Industrial electronic connector JUSHUO AFC20-S04ACC-00 part of XFC series designed for connectivity
Connector Header 4 position 2mm Pitch
Durable electronic 1.0mm pitch horizontal SMT connector JUSHUO AFC10-S02QCA-00 with ROHS compliance
Connector Header 2 position 1mm Pitch 500mA Surface Mount, Right Angle -25℃~+85℃
1.5mm Pitch Horizontal SMT Connector JUSHUO AFC15-S08DCA-00 Electronic Component for Circuit Boards
Connector Header 8 position 1.5mm Pitch 1A Surface Mount, Right Angle -20℃~+85℃
Complete PCB Layout Design and Documentation Including JUSHUO AFC10-S05PCC-00 Model for Circuit Board
Connector Header 5 position 1mm Pitch
Electronic 2.0mm Horizontal SMT Socket Connector with Latch JUSHUO GH200-S05ACA-00 Solution
Connector Header 5 position 2mm Pitch 2A Surface Mount, Right Angle -25℃~+85℃
Compact and versatile JUSHUO AFC10-S11QCC-00 connector unit optimized for electronic device assembly
Connector Header 11 position 1mm Pitch
Precision engineered JUSHUO AFC12-S16DCC-00 connector suitable for demanding electronic environments
Connector Header 16 position 1.25mm Pitch
Wafer patch socket connector 125mm pitch JUSHUO 1.25T-8PWT ideal for FPC FFC mating and connection
Connector Header 8 position 1.25mm Pitch
connection solution JUSHUO AFC20-S10ACC-00 connector for electronic and industrial automation equipment
Connector Header 10 position 2mm Pitch
Send RFQ
Stock:
MOQ:
