1.0mm Pitch Horizontal SMT Connector JUSHUO AFC10-S03QCA-00 ROHS Certified with Electrical Performance
Manufacturer:
JUSHUO
Description:
Connector Header 3 position 1mm Pitch 500mA Surface Mount, Right Angle -25℃~+85℃
Category:
Headers, Male Pins/Headers, Male Pins
Specifications
Pins Structure:
1x3P
Reference Series:
SH
Contact Plating:
锡
Contact Material:
磷青铜;LCP
Operating Temperature:
-25℃~+85℃
Flame Retardant Rating:
UL94V-0
Pitch:
1mm
Voltage Rating (Max):
50V
Number Of PINs Per Row:
3
Number Of Rows:
1
X-Length Of Bottom Edge On Board (Spacing Line):
5.3mm
Z-Height Of The Board:
3.14mm
Mounting Type:
卧贴
Row Spacing:
-
Mfr. Part #:
AFC10-S03QCA-00
Package:
SMD,P=1mm,Surface Mount,Right Angle
Model Number:
AFC10-S03QCA-00
Introduction
Product Acknowledgement
This document serves as a Product Acknowledgement for the 1.0mm Pitch Horizontal SMT Connector, model AFC10-S**QCA-00. This specification is applicable to the 1.0 series products.
Product Attributes
- Brand: SHENZHEN JUSHUO ELECTRONIC CO.,LTD
- Product Name: 1.0mm Pitch Horizontal SMT Connector
- Product Model: AFC10-S**QCA-00
- Version: 1.0
- Origin: Shenzhen, China
- Certifications: ROHS environmental protection requirements
Technical Specifications
| Item | Specification | Test Method | Performance Requirement |
|---|---|---|---|
| Standard Rating | |||
| Rated Voltage | 50V | ||
| Rated Current | 0.5A AC/DC | ||
| Operating Temperature Range | -25+105 | ||
| Operating Humidity Range | Below 90% Relative Humidity | ||
| Packing | |||
| Inner Packing | Joint and several | ||
| Outer Packing | Carton, sealed in the box, do not shake | ||
| Transport | |||
| Conditions | Avoid rain, snow, sunlight, collision, extrusion. Ambient temperature: -20 to +50 | ||
| Storage | |||
| Conditions | Ambient temperature: -20 to +50, Relative humidity: 90%, no corrosive gases | ||
| Part Name/Material | |||
| Part Name | Model | Material | |
| Base | 1.0 LCP E130i | LCP | |
| Reed | 1.0 | Phosphor Copper | |
| Stator | 1.0 | Phosphor Copper | |
| Appearance | |||
| Plastic Parts | Free of obvious scars, mottled, cracked, burr, flash, lack of material, and deformation affecting use. | ||
| Metal Parts | Smooth and clean surface, no rust, oxidation, peeling, blackening, or obvious mechanical damage. | ||
| Electrical Characteristics | |||
| Contact Resistance | Plug in connector, test with contact resistance meter. | 20m Max | |
| Insulation Resistance | Apply 500V DC voltage between adjacent contacts and between contacts and enclosure for 1 minute. | 100M Min | |
| Withstand Voltage | Apply 500V AC voltage between adjacent contacts and between contacts and enclosure for 1 minute. | No breakdown and flashover | |
| Environmental Characteristics | |||
| Heating Test | Place plug connector in +1052 environment for 96H, then test after 1-2H recovery. | Appearance: no damage. Contact Resistance: 30m Max | |
| Cold Tolerance Test | Place plug connector in -252 environment for 96H, then test after 1-2H recovery. | Appearance: no damage. Contact Resistance: 30m Max | |
| Moisture Resistance Test | Place plug connector in 402, 90-96% RH environment for 96H, then test after 1-2H recovery. | Appearance: no damage. Insulation Resistance: 50M MIN. Withstand Voltage: 200VAC/min | |
| Temperature Cycle | 5 cycles: -253 (30min) -> Room Temp (1H) -> +1053 (30min) -> Room Temp (1H). Test after 2H recovery. | Appearance: no abnormality. Contact Resistance: 30m Max | |
| Salt Spray Test | Continuous spray with 5%1% NaCl solution for 24H. Wash with distilled water, test after 1-2H recovery. | Appearance: no damage or corrosion. Contact Resistance: 30m Max | |
| Weldability | Dip in 2355 tin solution for 2.50.5 seconds. | Tin area 95% | |
| Soldering Resistance | Place connector on PCB, undergo 2605 reflow or wave soldering for 51S. | 1. Plastic parts: no obvious deformation, damage, blistering. 2. Electrical characteristics must meet specifications. | |
| Mechanical Properties | |||
| Pin Fixing Force | Apply force at pin front end at 253mm/min rate until pin withdraws. | Single Pin: 7N Min | |
| Terminal Retention in Plastic Parts | Pull terminal from socket at 253mm/min rate along conductor direction. | Single Terminal: 5N Min | |
| Mechanical Life | Plug and unplug 50 times at 10 times/min speed (no power). | Contact Resistance: 30m Max | |
| Insert/Draw Force | Match socket and terminal, test insert/plug on same axis. Remove lock during test (205mm/minute). | See table below for PIN position specific values. | |
| PIN Position | Insert (N) | Pull Out (N) | PIN Position | Insert (N) | Pull Out (N) |
|---|---|---|---|---|---|
| 1 | 3.00 | 0.50 | 9 | 29.00 | 5.50 |
| 2 | 8.00 | 2.00 | 10 | 32.00 | 6.00 |
| 3 | 11.00 | 2.50 | 11 | 35.00 | 6.50 |
| 4 | 14.00 | 3.00 | 12 | 38.00 | 7.00 |
| 5 | 17.00 | 3.50 | 13 | 41.00 | 7.50 |
| 6 | 20.00 | 4.00 | 14 | 44.00 | 8.00 |
| 7 | 23.00 | 4.50 | 15 | 47.00 | 8.50 |
| 8 | 26.00 | 5.00 | 16 | 50.00 | 9.00 |
2410121633_JUSHUO-AFC10-S03QCA-00_C2764182.pdf
Related Products
Durable Electrical Connector JUSHUO AFC10-S06PCC-00 Featuring PCB Layout for Electronic Applications
Connector Header 6 position 1mm Pitch
Industrial electronic connector JUSHUO AFC20-S04ACC-00 part of XFC series designed for connectivity
Connector Header 4 position 2mm Pitch
Durable electronic 1.0mm pitch horizontal SMT connector JUSHUO AFC10-S02QCA-00 with ROHS compliance
Connector Header 2 position 1mm Pitch 500mA Surface Mount, Right Angle -25℃~+85℃
1.5mm Pitch Horizontal SMT Connector JUSHUO AFC15-S08DCA-00 Electronic Component for Circuit Boards
Connector Header 8 position 1.5mm Pitch 1A Surface Mount, Right Angle -20℃~+85℃
Complete PCB Layout Design and Documentation Including JUSHUO AFC10-S05PCC-00 Model for Circuit Board
Connector Header 5 position 1mm Pitch
Electronic 2.0mm Horizontal SMT Socket Connector with Latch JUSHUO GH200-S05ACA-00 Solution
Connector Header 5 position 2mm Pitch 2A Surface Mount, Right Angle -25℃~+85℃
Compact and versatile JUSHUO AFC10-S11QCC-00 connector unit optimized for electronic device assembly
Connector Header 11 position 1mm Pitch
Precision engineered JUSHUO AFC12-S16DCC-00 connector suitable for demanding electronic environments
Connector Header 16 position 1.25mm Pitch
Wafer patch socket connector 125mm pitch JUSHUO 1.25T-8PWT ideal for FPC FFC mating and connection
Connector Header 8 position 1.25mm Pitch
connection solution JUSHUO AFC20-S10ACC-00 connector for electronic and industrial automation equipment
Connector Header 10 position 2mm Pitch
Send RFQ
Stock:
MOQ:
