Horizontal SMT connector latch 1.25mm pitch JUSHUO GH125-S09DCA-00 rated current 1.0A AC DC and ROHS certification
Manufacturer:
JUSHUO
Description:
Connector Header 9 position 1.25mm Pitch 1A Surface Mount, Right Angle -25℃~+85℃
Category:
Headers, Male Pins/Headers, Male Pins
Specifications
Y-Width Of Bottom Edge On Board:
4.25mm
Pins Structure:
1x9P
Reference Series:
GH
Contact Plating:
锡
Contact Material:
磷青铜;LCP
Operating Temperature:
-25℃~+85℃
Flame Retardant Rating:
UL94V-0
Pitch:
1.25mm
Voltage Rating (Max):
50V
Number Of PINs Per Row:
9
Number Of Rows:
1
X-Length Of Bottom Edge On Board (Spacing Line):
14.55mm
Z-Height Of The Board:
4.05mm
Mounting Type:
卧贴
Row Spacing:
-
Mfr. Part #:
GH125-S09DCA-00
Package:
SMD,P=1.25mm,Surface Mount,Right Angle
Model Number:
GH125-S09DCA-00
Introduction
Product Overview
This document is a product acknowledgment for the 1.25mm pitch horizontal SMT connector with latch, model GH125-S**DCA-00. It details the product's specifications, performance characteristics, and environmental requirements.
Product Attributes
- Brand: SHENZHEN JUSHUO ELECTRONIC CO.,LTD
- Origin: Shenzhen, China
- Certifications: ROHS environmental protection requirements
Technical Specifications
| Item | Specifications | Test Method | Performance Requirements |
| Standard Rating | |||
| Rated voltage | 50V | ||
| Rated current | 1.0A AC/DC | ||
| Operating temperature range | -2585 | ||
| Operating humidity range | Relative humidity is below 90% | ||
| Environmental Protection | |||
| Compliance | Products in line with ROHS environmental protection requirements. | ||
| Packing | |||
| Description | Inner packing is joint and several, outer packing is carton, product is sealed in the box, do not shake. | ||
| Transport | |||
| Conditions | Allowed by any means, avoid rain, snow, sunlight, collision, extrusion. Ambient temperature: -20 to +50. | ||
| Storage | |||
| Conditions | Ambient temperature: -20 to +50, relative humidity not more than 90%, no acid, alkaline, or other corrosive gases. | ||
| Component Name/Material | |||
| Base | GH LCP E130i | ||
| Pin | GH Phosphor copper | ||
| Stator | GH Phosphor copper | ||
| Appearance and Size | |||
| Appearance | Plastic parts: no obvious scars, mottled, cracked, burr, flash, lack of material, deformation. Metal parts: smooth, no rust, oxidation, peeling, blackening, mechanical damage. | ||
| Size | Reference engineering drawing | ||
| Electrical Characteristics | |||
| Contact resistance | Plug in connector, test with contact resistance meter. | 20m Max | |
| Insulation resistance | Plug in connector, apply 100V DC between adjacent contacts and between contacts and enclosure for 1 minute. | 500M Min | |
| Withstand voltage | Plug in connector, apply 500V AC between adjacent contacts and between contacts and enclosure for 1 minute. | No breakdown and flashover | |
| Environmental Characteristics | |||
| Heating test | Place plugged connector in +852 for 96H, then in normal environment for 1-2H. | Appearance: no damage. Contact resistance: 60m Max. | |
| Cold tolerance test | Place plugged connector in -252 for 96H, then in normal environment for 1-2H. | Appearance: no damage. Contact resistance: 60m Max. | |
| Moisture resistance test | Place plugged connector in 402, 90-96% RH for 96H, then in normal environment for 1-2H. | Appearance: no damage. Insulation resistance: 60M MIN. Withstand voltage: 250V AC/minute MIN. | |
| Temperature cycle | Test samples in high/low temp chamber: -253 (30min), room temp (1H), +853 (30min), room temp (1H). Repeat 5 cycles. Recover 2H. | Appearance: no abnormalities. Contact resistance: 60m Max. | |
| Salt spray test | Spray with (51)% NaCl solution for 24H. Wash with distilled water, recover 1-2H. | Appearance: no damage, corrosion. Contact resistance: 60m Max. | |
| Weldability | Dip test sample in 2605 tin solution for 2.50.5 seconds. | Tin area above 95% | |
| Soldering resistance | Place connector on PCB, reflow/wave solder at 2605 for 51S. | 1. Plastic parts: no obvious deformation, damage, blistering. 2. Electrical characteristics must meet specifications. | |
| Mechanical Properties | |||
| Pin fixing force | Fix pin holder, apply force at 253mm/min rate until pin withdraws. | Single pin 5N Min | |
| Terminal retention in plastic parts | Terminal and socket fit, pull terminal from socket at 253mm/min rate along wire direction. | Single terminal: 7N Min | |
| Mechanical life | Plug and unplug 30 times at 10 times/min speed under no power. | Contact resistance: 80m Max. | |
| Terminal crimp lead line strength | Axial pullout force on crimped wire at 253mm/min rate. | 26AWG wire: 17.8N. 28AWG wire: 8.9N. 30AWG wire: 4.4N. 32AWG wire: 2.2N. | |
| Insertion/Pull-out force | 1. Fit socket and terminal, test insertion/removal on same axis. Remove socket lock. Test speed: 205mm/min. | Insertion force: 2N(Per pin). Pull-out force: 0.3N(Per pin). | |
2410121633_JUSHUO-GH125-S09DCA-00_C2886772.pdf
Related Products
Durable Electrical Connector JUSHUO AFC10-S06PCC-00 Featuring PCB Layout for Electronic Applications
Connector Header 6 position 1mm Pitch
Industrial electronic connector JUSHUO AFC20-S04ACC-00 part of XFC series designed for connectivity
Connector Header 4 position 2mm Pitch
Durable electronic 1.0mm pitch horizontal SMT connector JUSHUO AFC10-S02QCA-00 with ROHS compliance
Connector Header 2 position 1mm Pitch 500mA Surface Mount, Right Angle -25℃~+85℃
1.5mm Pitch Horizontal SMT Connector JUSHUO AFC15-S08DCA-00 Electronic Component for Circuit Boards
Connector Header 8 position 1.5mm Pitch 1A Surface Mount, Right Angle -20℃~+85℃
Complete PCB Layout Design and Documentation Including JUSHUO AFC10-S05PCC-00 Model for Circuit Board
Connector Header 5 position 1mm Pitch
Electronic 2.0mm Horizontal SMT Socket Connector with Latch JUSHUO GH200-S05ACA-00 Solution
Connector Header 5 position 2mm Pitch 2A Surface Mount, Right Angle -25℃~+85℃
Compact and versatile JUSHUO AFC10-S11QCC-00 connector unit optimized for electronic device assembly
Connector Header 11 position 1mm Pitch
Precision engineered JUSHUO AFC12-S16DCC-00 connector suitable for demanding electronic environments
Connector Header 16 position 1.25mm Pitch
Wafer patch socket connector 125mm pitch JUSHUO 1.25T-8PWT ideal for FPC FFC mating and connection
Connector Header 8 position 1.25mm Pitch
connection solution JUSHUO AFC20-S10ACC-00 connector for electronic and industrial automation equipment
Connector Header 10 position 2mm Pitch
Send RFQ
Stock:
MOQ:
