1.25mm pitch SMT connector horizontal with latch JUSHUO GH125-S07DCA-00 rated 50 volts 1 amp AC DC
Manufacturer:
JUSHUO
Description:
Connector Header 7 position 1.25mm Pitch 1A Surface Mount, Right Angle -25℃~+85℃
Category:
Headers, Male Pins/Headers, Male Pins
Specifications
Y-Width Of Bottom Edge On Board:
4.25mm
Pins Structure:
1x7P
Reference Series:
GH
Contact Plating:
锡
Contact Material:
磷青铜;LCP
Operating Temperature:
-25℃~+85℃
Flame Retardant Rating:
UL94V-0
Pitch:
1.25mm
Voltage Rating (Max):
50V
Number Of PINs Per Row:
7
Number Of Rows:
1
X-Length Of Bottom Edge On Board (Spacing Line):
12.05mm
Z-Height Of The Board:
4.05mm
Mounting Type:
卧贴
Row Spacing:
-
Mfr. Part #:
GH125-S07DCA-00
Package:
SMD,P=1.25mm,Surface Mount,Right Angle
Model Number:
GH125-S07DCA-00
Introduction
Product Overview
This document is a product acknowledgment for the 1.25mm pitch horizontal SMT connector with latch, model GH125-S**DCA-00. It details the product's specifications, environmental characteristics, and mechanical properties, ensuring it meets standard requirements for various applications.
Product Attributes
- Brand: (SHENZHEN JUSHUO ELECTRONIC CO.,LTD)
- Product Name: 1.25mm( (1.25mm pitch horizontal SMT connector with latch)
- Product Model: GH125-S**DCA-00
- Origin: Shenzhen, China
- Certifications: ROHS compliant
Technical Specifications
| Item | Specifications/Requirements | Test Method |
| Standard Rating | ||
| Rated Voltage | 50V | |
| Rated Current | 1.0A AC/DC | |
| Operating Temperature Range | -2585 | |
| Operating Humidity Range | Relative humidity is below 90% | |
| Environmental Protection | ||
| Compliance | Products in line with ROHS environmental protection requirements. | |
| Packing | ||
| Method | Inner packing is joint and several, outer packing is carton, product is sealed in the box, do not shake. | |
| Transport | ||
| Conditions | Avoid rain, snow, sunlight, collision, extrusion. Ambient temperature: -20 to +50. | |
| Storage | ||
| Conditions | Ambient temperature: -20 to +50, relative humidity not more than 90%, no acid, alkaline, or other corrosive gases. | |
| Part Name/Material | ||
| Base | GH LCP E130i | |
| Pin | GH Phosphor copper | |
| Stator | GH Phosphor copper | |
| Electrical Characteristics | ||
| Contact Resistance | 20m Max | Plug in connector, test with contact resistance meter. |
| Insulation Resistance | 500M Min | Apply 100V DC between adjacent contacts and between contacts and enclosure for 1 minute. |
| Withstand Voltage | No breakdown and flashover | Apply 500V AC between adjacent contacts and between contacts and enclosure for 1 minute. |
| Environmental Characteristics | ||
| Heating Test (+85) | Appearance: No damage. Contact Resistance: 60m Max. | Place in +852 for 96H, then test after 1-2H at normal temp. |
| Cold Test (-25) | Appearance: No damage. Contact Resistance: 60m Max. | Place in -252 for 96H, then test after 1-2H at normal temp. |
| Moisture Resistance Test (40, 90-96% RH) | Appearance: No damage. Insulation Resistance: 60M Min. Withstand Voltage: 250V AC/minute MIN. | Place in 402, 90-96% RH for 96H, then test after 1-2H at normal temp. |
| Temperature Cycle (-25 to +85, 5 cycles) | Appearance: No abnormality. Contact Resistance: 60m Max. | -25 (30min) -> Room Temp (1H) -> +85 (30min) -> Room Temp (1H). Recover 2H. |
| Salt Spray Test (5% NaCl, 24H) | Appearance: No damage, corrosion. Contact Resistance: 60m Max. | Spray with 5% NaCl solution for 24H, wash with distilled water, recover 1-2H. |
| Weldability | Tin area above 95% | Dip in 2605 tin solution for 2.50.5 seconds. |
| Soldering Resistance | 1. Plastic parts: No obvious deformation, damage, blistering. 2. Electrical characteristics must meet specifications. | Reflow or wave soldering at 2605 for 51S. |
| Mechanical Properties | ||
| Pin Fixing Force | Single pin 5N min | Apply force at 253mm/min rate until pin withdraws. |
| Terminal Retention in Plastic Parts | Single terminal: 7N min | Pull terminal out of socket at 253mm/min rate along wire direction. |
| Mechanical Life | Contact Resistance: 80m Max. | Plug and unplug 30 times at 10 times/min speed without power. |
| Terminal Crimp Wire Strength | 26AWG wire: 17.8N; 28AWG wire: 8.9N; 30AWG wire: 4.4N; 32AWG wire: 2.2N | Axial pullout force at 253mm/min rate. |
| Insertion/Pullout Force | Insertion force: 2N(Per pin); Pullout force: 0.3N(Per pin) | Fit socket and terminal, insert/remove on same axis. Remove socket lock. (Test speed: 205mm/min) |
2410121633_JUSHUO-GH125-S07DCA-00_C2886770.pdf
Related Products
Durable Electrical Connector JUSHUO AFC10-S06PCC-00 Featuring PCB Layout for Electronic Applications
Connector Header 6 position 1mm Pitch
Industrial electronic connector JUSHUO AFC20-S04ACC-00 part of XFC series designed for connectivity
Connector Header 4 position 2mm Pitch
Durable electronic 1.0mm pitch horizontal SMT connector JUSHUO AFC10-S02QCA-00 with ROHS compliance
Connector Header 2 position 1mm Pitch 500mA Surface Mount, Right Angle -25℃~+85℃
1.5mm Pitch Horizontal SMT Connector JUSHUO AFC15-S08DCA-00 Electronic Component for Circuit Boards
Connector Header 8 position 1.5mm Pitch 1A Surface Mount, Right Angle -20℃~+85℃
Complete PCB Layout Design and Documentation Including JUSHUO AFC10-S05PCC-00 Model for Circuit Board
Connector Header 5 position 1mm Pitch
Electronic 2.0mm Horizontal SMT Socket Connector with Latch JUSHUO GH200-S05ACA-00 Solution
Connector Header 5 position 2mm Pitch 2A Surface Mount, Right Angle -25℃~+85℃
Compact and versatile JUSHUO AFC10-S11QCC-00 connector unit optimized for electronic device assembly
Connector Header 11 position 1mm Pitch
Precision engineered JUSHUO AFC12-S16DCC-00 connector suitable for demanding electronic environments
Connector Header 16 position 1.25mm Pitch
Wafer patch socket connector 125mm pitch JUSHUO 1.25T-8PWT ideal for FPC FFC mating and connection
Connector Header 8 position 1.25mm Pitch
connection solution JUSHUO AFC20-S10ACC-00 connector for electronic and industrial automation equipment
Connector Header 10 position 2mm Pitch
Send RFQ
Stock:
MOQ:
