2.5mm Vertical Surface Mount Connector JUSHUO AFC25-S03CCA-00 with Low Electrical Contact Resistance
Manufacturer:
JUSHUO
Description:
Connector Header 3 position 2.5mm Pitch 3A Surface Mount,Vertical -20℃~+85℃
Category:
Headers, Male Pins/Headers, Male Pins
Specifications
Y-Width Of Bottom Edge On Board:
5.95mm
Pins Structure:
1x3P
Reference Series:
XH
Contact Plating:
锡
Contact Material:
黄铜;LCP
Operating Temperature:
-20℃~+85℃
Flame Retardant Rating:
UL94V-0
Pitch:
2.5mm
Voltage Rating (Max):
250V
Number Of PINs Per Row:
3
Number Of Rows:
1
X-Length Of Bottom Edge On Board (Spacing Line):
10mm
Z-Height Of The Board:
7.9mm
Row Spacing:
-
Mounting Type:
立贴
Mfr. Part #:
AFC25-S03CCA-00
Package:
SMD,P=2.5mm
Model Number:
AFC25-S03CCA-00
Introduction
Product Overview
This product acknowledgment document details the specifications for the 2.5mm vertical surface mount connector, model AFC25-S**CCA-00. It covers standard ratings, packaging, transportation, storage, part details, electrical, environmental, and mechanical characteristics.
Product Attributes
- Brand: SHENZHEN JUSHUO ELECTRONIC CO.,LTD
- Origin: China (implied by company address)
- Certifications: ROHS environmental protection requirements
Technical Specifications
| Item | Specifications | Requirements | Test Method |
| Standard Rating | |||
| Rated Voltage | 250V | ||
| Rated Current | 3.0A AC/DC | ||
| Operating Temperature Range | -25+105 | ||
| Operating Humidity Range | Relative humidity is below 90% | ||
| Part Name/Specification/Material | |||
| Base | 2.5 LCP E130i | ||
| Pin | 2.5 Brass | ||
| Stator | 2.5 Brass | ||
| Electrical Characteristics | |||
| Contact Resistance | 20m Max | Plug in the connector and test it with a contact resistance meter to measure both terminals of the connector Form a closed loop between. | |
| Insulation Resistance | 1000M Min | 1000V DC for 1 minute between adjacent contacts and between contacts and enclosure. | Plug in the connector and apply 1000V DC voltage between the adjacent contacts and between the contacts and the enclosure for 1 minute. |
| Withstand Voltage | No breakdown and flashover | 1000V AC for 1 minute between adjacent contacts and between contacts and enclosure. | Plug in the connector and apply 1000V AC voltage between the adjacent contacts and between the contacts and the enclosure for 1 minute. |
| Environmental Characteristics | |||
| Heating Test | Appearance: no damage. Contact resistance: 30m Max | +1052 for 96H, then 1~2H in normal environment. | Put the plug connector in the environment of +1052 for 96H, take it out and put it in the normal environment for 1~2H before testing. |
| Cold Tolerance Test | Appearance: no damage. Contact resistance: 30m Max | -252 for 96H, then 1~2H in normal environment. | The plug connector was placed in the environment with the temperature of -252 for 96H, and was taken out and placed in the normal environment for 1~2H before being tested. |
| Moisture Resistance Test | Appearance: no damage. Insulation resistance: 500M Min. Withstand voltage: 800V AC/minute MIN | 402, 90~96% RH for 96H, then 1~2H in normal environment. | Place the plug connector in an environment with a temperature of 402 and relative humidity of 90~96%.Last for 96H, after the test, take it out and put it in the normal environment for 1~2H before the test. |
| Temperature Cycle | Appearance: no abnormalities. Contact resistance: 30m Max | 5 cycles of: -253 for 30 min, room temp for 1H, +1053 for 30 min, room temp for 1H. Recover 2H. | Put the test samples into the high and low temperature test chamber, and adjust the temperature according to the following steps: A. Place for 30 minutes under the constant temperature of -253 B. Place at room temperature for 1 hour C. Place for 30 minutes at a constant temperature of +1053 D. Place at room temperature for 1 hour From a to d is a cycle period, a total of 5 cycles are carried out, and 2H is recovered in the normal environmentCheck later. |
| Salt Spray Test | Appearance: no damage or corrosion (hardware should not expose the bottom metal of serious corrosion; use pre-plating, blanking surface is allowed to have slight corrosion that does not affect its performance). Contact resistance: 30m Max | Continuous spray for 24H with 51% NaCl solution, then wash with distilled water, recover 1~2H. | The test sample was suspended from the top of the test box, and the concentration of (51)% Sodium Chloride Solution was continuously sprayed with 24H. After testing, the surface precipitates were lightly washed with flowing steaming water, then the 1~2H was rechecked at normal temperature. |
| Weldability | Tin area above 95% | Dip the welded part into 2455 tin solution for 2.50.5 seconds. | Dip the welded part of the test sample into 2455 tin solution and hold 2.50.5 seconds. |
| Soldering Resistance | 1. Plastic parts shall be free from obvious deformation, damage and blistering. 2. Electrical characteristics must meet the specifications. | Reflow soldering or wave soldering at 2605 for 51S. | Place the connector on the PCB, and then reflow the product through 260 5 Or wave soldering for 5 1s. |
| Mechanical Properties | |||
| Pin Fixing Force | Single pin 12N Min | Fix the pin holder on the drawing machine and apply force on the front end of the pin at a rate of 253mm per minute until the pin is withdrawn from the pin holder. | |
| Terminal Retention in Plastic Parts | Single terminal: 15N Min | The terminal shall be matched with the hole seat, and at the rate of 253mm per minute along the conductor direction, the force that the terminal is pulled out of the socket. | |
| Mechanical Life | Contact resistance: 30m Max | Plug and unplug 50 times at the speed of 10 times / min under no power on state. | Under no power on state, plug and unplug 50 times at the speed of 10 times / min. |
| Insertion/Extraction Force | See table below | Test speed: 205mm/minute. Remove the lock of the hole seat. | (1) Fit the hole seat and the terminal, and conduct the insertion and removal test on the same axis with the needle seat. Remove the lock of the hole seat (test speed: 20 5mm) minute during the test |
| Position | Insertion (N) | Pull out (N) | |
| 1 | 16.00 | 2.00 | |
| 2 | 20.00 | 10.00 | |
| 3 | 24.00 | 12.00 | |
| 4 | 28.00 | 14.00 | |
| 5 | 32.00 | 16.00 | |
| 6 | 36.00 | 18.00 | |
| 7 | 40.00 | 20.00 | |
| 8 | 44.00 | 22.00 | |
| 9 | 48.00 | 24.00 | |
| 10 | 52.00 | 26.00 | |
| 11 | 56.00 | 28.00 | |
| 12 | 60.00 | 30.00 | |
| 13 | 64.00 | 32.00 | |
| 14 | 68.00 | 34.00 | |
| 15 | 72.00 | 36.00 | |
| 16 | 76.00 | 38.00 | |
2410121633_JUSHUO-AFC25-S03CCA-00_C2764257.pdf
Related Products
Durable Electrical Connector JUSHUO AFC10-S06PCC-00 Featuring PCB Layout for Electronic Applications
Connector Header 6 position 1mm Pitch
Industrial electronic connector JUSHUO AFC20-S04ACC-00 part of XFC series designed for connectivity
Connector Header 4 position 2mm Pitch
Durable electronic 1.0mm pitch horizontal SMT connector JUSHUO AFC10-S02QCA-00 with ROHS compliance
Connector Header 2 position 1mm Pitch 500mA Surface Mount, Right Angle -25℃~+85℃
1.5mm Pitch Horizontal SMT Connector JUSHUO AFC15-S08DCA-00 Electronic Component for Circuit Boards
Connector Header 8 position 1.5mm Pitch 1A Surface Mount, Right Angle -20℃~+85℃
Complete PCB Layout Design and Documentation Including JUSHUO AFC10-S05PCC-00 Model for Circuit Board
Connector Header 5 position 1mm Pitch
Electronic 2.0mm Horizontal SMT Socket Connector with Latch JUSHUO GH200-S05ACA-00 Solution
Connector Header 5 position 2mm Pitch 2A Surface Mount, Right Angle -25℃~+85℃
Compact and versatile JUSHUO AFC10-S11QCC-00 connector unit optimized for electronic device assembly
Connector Header 11 position 1mm Pitch
Precision engineered JUSHUO AFC12-S16DCC-00 connector suitable for demanding electronic environments
Connector Header 16 position 1.25mm Pitch
Wafer patch socket connector 125mm pitch JUSHUO 1.25T-8PWT ideal for FPC FFC mating and connection
Connector Header 8 position 1.25mm Pitch
connection solution JUSHUO AFC20-S10ACC-00 connector for electronic and industrial automation equipment
Connector Header 10 position 2mm Pitch
Send RFQ
Stock:
MOQ:
