USB AF connector SHOU HAN AF SC-JBT17.6 designed for secure connection force of 35N and rated DC 30 volts 1.5 amperes
Manufacturer:
SHOU HAN
Description:
USB-A (USB TYPE-A) Receptacle Connector 4 Positionx2 Right Angle
Category:
USB, DVI, HDMI Connector Adapters/USB, DVI, HDMI Connector Assemblies
Specifications
Length:
17.6mm
Number Of Ports:
2
Supplementary Features:
-
Number Of Contacts:
4Px2
Mounting Type:
弯插
Center Height:
-
Current Rating:
1.5A
Detection Color:
白色
Voltage Rating:
30V
Operating Temperature:
-25℃~+85℃
Connector Type:
Type-A
Connect-Disconnect Life:
5千次
Gender:
母
Mfr. Part #:
AF SC-JBT17.6
Package:
Through Hole,Right Angle
Model Number:
AF SC-JBT17.6
Introduction
Product Overview
This document outlines the specifications for a USB AF AF connector (Part No: SC-JBT17.6) manufactured by Shenzhen Shouhan Technology Co., Ltd. It details the product's electrical, mechanical, and durability characteristics, designed for operation within a practical temperature range of -25~85C.
Product Attributes
- Brand: (SHENZHEN SHOUHAN TECHNOLOGY CO.,LTD)
- Origin: (Shenzhen)
- Color: WHITE
- Contact Persons: (Li Chunfeng), (Zhong Huahua), (Luo Xiaojin)
- Contact Information: Tel: 0755-27597601, Fax: 0755-27597491
Technical Specifications
| Item | Project | Test Conditions | Performance/Specification |
|---|---|---|---|
| RATING | DC 30V 1.5A | ||
| -25~85C | |||
| STANDARD ATMOSPHEIC CONDITIONS | (1) | 5C TO 35 | |
| (2) | 45% TO 85% | ||
| (3) | 86Kpa TO 106Kpa | ||
| MECHANICAL | CONNECTION FORCE | MEASUREMENT SHALL BE MADE AFTER CONNECTING AND DISCONNECTING USING STANDARD PLUG GAUGE 3 TIMES. | 35N |
| DISCONNECTI ON FORCE | MEASUREMENT SHALL BE MADE AFTER CONNECTING AND DISCONNECTING USING STANDARD PLUG GAUGE 3 TIMES. | 10N MIN | |
| TERMINAL STRENGTH | A STATIC LOAD OF 0.1N/m(1kgf/cm)SHALL BE APPLIED TO THE TIP OF THE TERMINAL FOR 1 MIN IN ANY DIRECTION. THERE SHALL BE NO DAMAGE TO THE TERMINAL SUCH AS CRACKS, LOOSENESS OR PLAY ELECTRICAL ,AND MECHANICAL CHARACTERISTICS SHALL BE SATISFIED. | ||
| ELECTRICAL | CONTACT RESISTANCE | MEASURED AT SMALL CURRENT 100m A OR LESS 1000Hz | 30m MAX |
| INSULATION RESISTANCE | APPLY A VOLTAGE OF 100V DC FOR 1 MIN TO FOLLOWING PORTIONS AFTER WHICH MEASUREMENT SHALL BE MADE: (1) BETWEEN BODY AND CONDUCTOR (2) BETWEEN CONDUCTORS NOT TO BE CONTACT (3) BETWEEN CONDUCTORS NOT TO BE WHEN PLUG IS INSERTED | 1000M MIN | |
| DIELECTRIC STRENGTH | AC 500V ims(50~60Hz)FOR 1 MIN TRIP CURRENT:0.5mA (1) BETWEEN BODYAND CONDUCTOR (2) BETWEEN CONDUCTORS NOT TO BE CONTACL (3) BETWEEN CONDUCTORS NOT TO BE WHEN PLUG IS INSERTED. WITHOUT DAMAGE TO PARTS ARCING OR BREAKDOWN ETC. | ||
| DURABILITY | SOLDERA- BILITY TEST | (1) THE TOP OF THE TERMINALS SHALL BE DIPPED 1mm IN THE SOLDER BATH OF 2305 FOR 30.5 SECONDS. SOLDER WETTING TIME SHALL BE 3 SEC OR LESS. (2) THE AREA OF SOLDERING SHOULD BE OVER 75% | |
| RESISTANCE TO SOLDERING HEAT TEST (REFLOW SOLDERING CONDITIONS) | PREHEAT: TEMPERATURE ON THE COPPER FOIL SURFACE SHOULD REACH 180. TALLEST TEMPERATURE: TEMPERATURE ON THE COPPER FOIL SURFACE SHOULD REACH THE PEAK IN 5 SECONDS OF 2305. WITHOUT DEFORMATION OF CASE OR EXCESSIVE LOOSENESS OF TERMINALS. ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED. | ||
| RESISTANCE TO SOLDERING HEAT TEST (SOLDERING IRON METHOD) | BIT TEMPERATURE 3305 APPLICATION TIME OF SOLDERING IRON 30.5 SEC. HOWEVER EXCESSIVE PRESSURE SHALL NOT BE APPLIED TO THE TERMINAL. WITHOUT DEFORMATION OF CASE OR EXCESSIVE LOOSENESS OF TERMINALS. ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED. | ||
| HUMIDITY TEST | THE JACK SHALL BE STORED AT A TEMPERATURE OF 402 AND A HUMIDITY OF 90%TO 96% FOR 96 HR, THEN THE JACK SHALL BE MAINTAINED AT STANDARD ATMOSPHERIC CONDITION FOR 1 HR FOR OTHER PROCEDURES. | ||
| HEAT TEST | THE JACK SHALL BE STORED AT A TEMPERATURE OF 702 FOR 96 HOURS, AND THEN IT SHALL BE SUBJECTED TO THE CONTROLLED RECOVERY CONDITIONS FOR 1 HOUR. THERE SHALL BE NO DAMAGE ON APPEARANCE. MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED. | ||
| COLD TEST | THE JACK SHALL BE STORED AT A TEMPERATURE OF -253 FOR 96 HOURS AND THEN IT SHALL BE SUBJECTED TO THE CONTROLLED RECOVERY CONDITIONS FOR 1 HOUR. THERE SHALL BE NO DAMAGE ON APPEARANCE. MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED. | ||
| LIFE TEST | WITHOUT LOAD | CONNECTION AND DISCONNECTION SHALL BE MADE WITH THE MATING PLUGS AND JACKS FOR 5000 CYCLES AT A SPEED OF 10 TO 25 CYCLES/MIN. | |
| LOAD: AT RATING CONDITION (NON-INDUCTIVE LOAD) | CONNECTION AND DISCONNECTION SHALL BE MADE 5000 CYCLES AT A SPEED 10 TO 20 CYCLES / MIN. | (1) CONTACT RESISTANCE SHALL BE 0.1 (2) DISCONNECTION FORCE SHALL BE 0.8 TO 2.0N (3) MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED. | |
| TEMPARATURE CYCLINGTEST | THE JACK SHALL BE SUBJECTED TO 5 CYCLES OF THE FOLLOWING CONDITIONS SHOWED IN THE FIGURE, AND THEN SHALL RETURNED AND ALLOWED TO REMAIN IN ROOM AMBIENT CONDITION FOR 30 MINUTES. | THERE SHALL BE NO DEFORMATION OR CRACKS IN MOLDED PART. INSERTION & EXTRACTION FORCE: 3 TO 20N. CONTACT RESISTANCE: MAX.30M. INSULATION RESISTANCE: MIN.100 M. DIELECTRIC WITHSTANDING VOLTAGE: 100VAC/MIN (BETWEEN TERMINALS). | |
| COLD&HEAT SHOCK TEST | THE JACK SHALL BE SUBJECTED TO 5 CYCLES OF THE FOLLOWING CONDITIONS SHOWED IN THE FIGURE, AND THEN SHALL RETURNED AND ALLOWED TO REMAIN IN ROOM AMBIENT CONDITION FOR 30 MINUTES. | THERE SHALL BE NO DEFORMATION OR CRACKS IN MOLDED PART. INSERTION & EXTRACTION FORCE: 3 TO 25N. CONTACT RESISTANCE: MAX.30M. INSULATION RESISTANCE: MIN.100 M. DIELECTRIC WITHSTANDING VOLTAGE: 500VAC/MIN (BETWEEN TERMINALS). |
2411251528_SHOU-HAN-AF-SC-JBT17-6_C5379911.pdf
Related Products
Micro USB Connector with 3000 Connect-Disconnect Life, Gold Plated Contacts, and Nickel Plated Shell for High Durability
USB-Micro B Receptacle Connector 5 Position Recessed Mount
IPX8 Waterproof USB Type-C Connector with 6P Contacts and 5000 Connect-Disconnect Life for Durable Performance
USB-C (USB TYPE-C) Receptacle Connector 6 Position Surface Mount, Right Angle
IPX8 Waterproof Type-C Connector with 6P Contacts and 3A Current Rating for Harsh Environments
USB-C (USB TYPE-C) Receptacle Connector 6 Position Recessed Mount
Durable USB Connector Type-A with DC 30V 1.5A Rating 5000 Connect-Disconnect Life and -25℃~+85℃ Operating Temperature
USB-A (USB TYPE-A) Receptacle Connector 4 Position Through Hole
SHOU HAN MICRO 6.4ZB5.0 Micro-B Connector with 5P Contacts, 1A Current Rating, and 3000 Connect-Disconnect Life for Reliable SMD Applications
USB-Micro B Receptacle Connector 5 Position Surface Mount, Right Angle
Mini-B USB Connector with 10P Contacts, 5000 Connect-Disconnect Life, and 30V 1A Rating for Reliable Electronic Devices
USB-Mini B Receptacle Connector 10 Position Surface Mount, Right Angle
Durable Type-C 6P Connector with 5000 Mating Cycles, 3A Current Rating, and LCP UL94 V-0 Material for High-Performance Applications
USB-C (USB TYPE-C) Receptacle Connector 6 Position Through Hole
High Durability Type-C Connector with 6P Contacts and 5000 Connect-Disconnect Life for Reliable Electrical Applications
USB-C (USB TYPE-C) Receptacle Connector 6 Position Surface Mount
Durable Type-C Connector with Stainless Steel Housing, Gold Plated Terminals, and 5000 Mating Cycles for Reliable Performance
USB-C (USB TYPE-C) Receptacle Connector 2 Position Through Hole
Robust Micro-B USB Connector with Gold Plated Contact, 10000 Connect-Disconnect Life, and LCP UL94V-0 Plastic for Reliable SMD Applications
USB-Micro B Receptacle Connector 5 Position Surface Mount, Right Angle
Send RFQ
Stock:
MOQ:
