High durability SHOU HAN 10.0 QCHTJB6.8 component rated DC 30V 1.5A for in environments from minus 25 to 85 degrees Celsius
Manufacturer:
SHOU HAN
Description:
USB-A (USB TYPE-A) Receptacle Connector 4 Position Surface Mount, Right Angle
Category:
USB, DVI, HDMI Connector Adapters/USB, DVI, HDMI Connector Assemblies
Specifications
Length:
10mm
Number Of Ports:
1
Supplementary Features:
-
Number Of Contacts:
4P
Mounting Type:
卧贴
Center Height:
-
Current Rating:
1.5A
Detection Color:
黑色
Voltage Rating:
30V
Operating Temperature:
-25℃~+85℃
Connector Type:
Type-A
Connect-Disconnect Life:
5千次
Gender:
母
Mfr. Part #:
10.0 QCHTJB6.8
Package:
SMD
Model Number:
10.0 QCHTJB6.8
Introduction
Product Overview
This document outlines the specifications for the QCHTJB6.8 product from SHENZHEN SHOUHAN TECHNOLOGY CO.,LTD. It details the product's electrical, mechanical, and durability characteristics, designed for use within a practical temperature range of -25~85C.
Product Attributes
- Brand: SHENZHEN SHOUHAN TECHNOLOGY CO.,LTD
- Origin: Shenzhen, China
- Part Number: QCHTJB6.8
- Customer Approval Signatures: , ,
- Contact: Tel: 0755-27597601, Fax: 0755-27597491
Technical Specifications
| Item | Test Conditions | Performance | |||
| RATING | |||||
| DC 30V 1.5A | |||||
| PRACTICAL TEMPERATURE RANGE | |||||
| -25~85C | -25C~+85C | ||||
| STANDARD ATMOSPHEIC CONDITIONS | |||||
| (1) BETWEEN BODY AND CONDUCTOR: 5C TO 35 | (1) 5~35 | ||||
| (2) BETWEEN CONDUCTORS NOT TO BE CONTACT45% TO 85% | (2) 45%~85% | ||||
| (3) PRESSURE86Kpa TO 106Kpa | (3) 86 Kpa~106Kpa | ||||
| MECHANICAL | |||||
| 1 | CONNECTION FORCE | MEASUREMENT SHALL BE MADE AFTER CONNECTING AND DISCONNECTING USING STANDARD PLUG GAUGE 3 TIMES | PLUG GAUGE 3 | 3.57Kgf MAX | |
| 2 | DISCONNECTI ON FORCE | MEASUREMENT SHALL BE MADE AFTER CONNECTING AND DISCONNECTING USING STANDARD PLUG GAUGE 3 TIMES | PLUG GAUGE 3 | 1.02Kgf MIN | |
| TERMINAL STRENGTH | A STATIC LOAD OF 0.1N/m(1kgf/cm)SHALL BE APPLIED TO THE TIP OF THE TERMINAL FOR 1 MIN IN ANY DIRECTION | 1 0.1N/m(1kgf/cm). | THERE SHALL BE NO DAMAGE TO THE TERMINAL SUCH AS CRACKS, LOOSENESS OR PLAY ELECTRICAL ,AND MECHANICAL CHARACTERISTICS SHALL BE SATISFIED | ||
| ELECTRICAL | |||||
| 3.1 | CONTACT RESISTANCE | MEASURED AT SMALL CURRENT 100m A OR LESS 1000Hz | 100 m A | 30m MAX | |
| 3.2 | INSULATION RESISTANCE | APPLY A VOLTAGE OF 100V DC FOR 1 MIN TO FOLLOWING PORTIONS AFTER WHICH MEASUREMENT SHALL BE MADE: (1) BETWEEN BODY AND CONDUCTOR (2) BETWEEN CONDUCTORS NOT TO BE CONTACT (3) BETWEEN CONDUCTORS NOT TO BE WHEN PLUG IS INSERTED | 100V DC 1 1 2 3 | 1000M MIN | |
| 3.3 | DIELECTRIC STRENGTH | AC 500V ims(50~60Hz)FOR 1 MIN TRIP CURRENT:0.5mA (1) BETWEEN BODYAND CONDUCTOR (2) BETWEEN CONDUCTORS NOT TO BE CONTACL (3) BETWEEN CONDUCTORS NOT TO BE WHEN PLUG IS INSERTED | AC 500V 50Hz/min 1 0.5mA, : (1) (2) (3) | WITHOUT DAMAGE TO PARTS ARCING OR BREAKDOWN ETC | |
| URABILITY | |||||
| 4.1 | SOLDERABILITY TEST | THE TOP OF THE TERMINALS SHALL BE DIPPED 1mm IN THE SOLDER BATH OF 2505 FOR 50.5 SECONDS | 1mm ,2505,5 0.5 | 1SOLDER WETTING TIME SHALL BE 3 SEC OR LESS 2THE AREA OF SOLDERING SHOULD BE OVER 75% | 1 3 2 75% |
| 4.2 | RESISTANCE TO SOLDERING HEAT TEST | REFLOW SOLDERING CONDITIONS: PREHEAT:TEMPERATURE ON THE COPPER FOIL SURFACE SHOULD REACH 180.120 SECONDS AFTER THE P.C.B ENTERED INTO THE SOLDERING EQUIPMENT. TALLEST TEMPERATURE:TEMPERATURE ON THE COPPER FOIL SURFACE SHOULD REACH THE PEAK TEMPERATURE OF 2605 WITH IN 20 SECONDS. | :180,120s :260520 | WITHOUT DEFOR MATION OF CASE OR EXCESSIVE LOOSENESS OF TEMINALS ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED | |
| SOLDERING IRON METHOD: BIT TEMPERATURE 3305 APPLICATION TIME OF SOLDERING IRON30.5 SEC HOWEVER EXCESSIVE PRESSURE SHALL NOT BE APPLIED TO THE TERMINAL | 3305 30.5 | WITHOUT DEFORMATION OF CASE OR EXCESSIVE LOOSENESS OF TEMINALS ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED | |||
| 4.3 | HUMIDITY TEST | THE JACK SHALL BE STORED AT A TEMPERATURE OF 402 AND A HUMIDITY OF 90%TO 96% FOR 96 Hr,THEN THE JACK SHALL BE MAINTAINED AT STANDARD ATMOSPHERIC CONDITION FOR 1 Hr FOR OTHER PROCEDURES | 40290~96% Hr 96 1 | ||
| 4.4 | HEAT TEST | THE JACK SHALL BE STORED AT A TEMPERATURE OF702 FOR 96 HOURSAND THEN IT SHALL BE SUBJECTED TO THE CONTROLLED RECOVERY MBASURBM | 70296 1 | THERE SHALL BE NO DAMAGE ON APPEARANCE MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED | |
| 4.5 | COLD TEST | THE JACK SHALL BE STORED AT A TEMPERATURE OF-253 FOR 96 HOURS AND THEN IT SHALL BE SUBJECTED TO THE CONTROLLED RECOVERY CONDITIONS FOR 1 HOUR AFTER WHICH | -25396 1 | THERE SHALL BE NO DAMAGE ON APPEARANCE MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED | |
| 4.6 | LIFE TEST | CONNECTION AND DISCONNECTION SHALL BE MADE 5000 CYCLES AT A SPEED 10 TO 20 CYCLES / MIN LOAD AT RATING CONDITION NON-INDUCTIVE LOAD | ()1 10-20 5000 | (1) CONTACT RESISTANCE SHALL BE 0.1 (2) DISCONNECTION FORCE SHALL BE 0.8 TO 2.0N (3) MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED | (1) 0.1 (2) 0.8~2.0N (3) :, |
| CONNECTION AND DISCONNECTION SHALL BE MADE WITH THE MATING PLUGS AND JACKS FOR 5000 CYCLES AT A SPEED OF 10 TO 25 CYCLES/MIN WITHOUT LOAD | Plug()1 10-255000 | ||||
| 4.7 | TEMPARATURE CYCLINGTEST | THE JACK SHALL BE SUB JECTED TO 5 CYCLES OF THE FOLLOWING CONDITIONS SHOWED IN THE FIGURE,AND THEN SHALL RETURNED ALLOWED TO REMAIN IN ROOM AMBIENT CONDITION FOR 30 MINUTES | 5 30 | THERE SHALL BE NO DEFORMATION OR CRACKS IN MOLDED PART. INSERTION EXTRACTION FORCE:3 TO 20N CONTACT RESISTANCE:MAX.30M INSULATION RESISTANCE: MIN.100 M DIELECTRIC WITHSTANDING VOLTAGE: 100VAC/MIN(BETWEEN TERMINALS) | 3N 20N 30m 100 M 100VAC |
| 4.8 | COLD&HEAT SHOCK TEST | THE JACK SHALL BE SUBJECTED TO5 CYCLES OF THE FOLLOWING CONDITIONS SHOWED IN THE FIGURE,AND THEN SHALL RETURNED AND ALLOWED TO REMAIN IN ROOM AMBIENT CONDITION FOR 30 MINUTES | 5 30 | THERE SHALL BE NO DEFORMATION OR CRACKS IN MOLDED PART. INSERTION EXTRACTION FORCE:3 TO 25N CONTACT RESISTANCE:MAX.30M INSULATION RESISTANCE: MIN.100 M DIELECTRIC WITHSTANDING VOLTAGE: 500VAC/MIN(BETWEEN TERMINALS) | 3N 25N 30m 100 M 500VAC |
2306091457_SHOU-HAN-10-0-QCHTJB6-8_C6386913.pdf
Related Products
Micro USB Connector with 3000 Connect-Disconnect Life, Gold Plated Contacts, and Nickel Plated Shell for High Durability
USB-Micro B Receptacle Connector 5 Position Recessed Mount
IPX8 Waterproof USB Type-C Connector with 6P Contacts and 5000 Connect-Disconnect Life for Durable Performance
USB-C (USB TYPE-C) Receptacle Connector 6 Position Surface Mount, Right Angle
IPX8 Waterproof Type-C Connector with 6P Contacts and 3A Current Rating for Harsh Environments
USB-C (USB TYPE-C) Receptacle Connector 6 Position Recessed Mount
Durable USB Connector Type-A with DC 30V 1.5A Rating 5000 Connect-Disconnect Life and -25℃~+85℃ Operating Temperature
USB-A (USB TYPE-A) Receptacle Connector 4 Position Through Hole
SHOU HAN MICRO 6.4ZB5.0 Micro-B Connector with 5P Contacts, 1A Current Rating, and 3000 Connect-Disconnect Life for Reliable SMD Applications
USB-Micro B Receptacle Connector 5 Position Surface Mount, Right Angle
Mini-B USB Connector with 10P Contacts, 5000 Connect-Disconnect Life, and 30V 1A Rating for Reliable Electronic Devices
USB-Mini B Receptacle Connector 10 Position Surface Mount, Right Angle
Durable Type-C 6P Connector with 5000 Mating Cycles, 3A Current Rating, and LCP UL94 V-0 Material for High-Performance Applications
USB-C (USB TYPE-C) Receptacle Connector 6 Position Through Hole
High Durability Type-C Connector with 6P Contacts and 5000 Connect-Disconnect Life for Reliable Electrical Applications
USB-C (USB TYPE-C) Receptacle Connector 6 Position Surface Mount
Durable Type-C Connector with Stainless Steel Housing, Gold Plated Terminals, and 5000 Mating Cycles for Reliable Performance
USB-C (USB TYPE-C) Receptacle Connector 2 Position Through Hole
Robust Micro-B USB Connector with Gold Plated Contact, 10000 Connect-Disconnect Life, and LCP UL94V-0 Plastic for Reliable SMD Applications
USB-Micro B Receptacle Connector 5 Position Surface Mount, Right Angle
Send RFQ
Stock:
MOQ:
