BOOMELE Boom Precision Elec 1.25T-5P SMT series 1.25mm pitch bar connectors for electrical connections
Manufacturer:
BOOMELE(Boom Precision Elec)
Description:
Connector Header 5 position 1.25mm Pitch Surface Mount,Vertical
Category:
Free Hanging, Panel Mount/Headers, Male Pins
Specifications
Y-Width Of Bottom Edge On Board:
4.75mm
Reference Series:
PicoBlade(MX 1.25)
Pins Structure:
1x5P
Contact Plating:
-
Contact Material:
-;-
Operating Temperature:
-25℃~+85℃
Flame Retardant Rating:
-
Supplementary Features:
-
Pitch:
1.25mm
Voltage Rating (Max):
125V
Number Of PINs Per Row:
5
Number Of Rows:
1
X-Length Of Bottom Edge On Board (Spacing Line):
-
Z-Height Of The Board:
3.7mm
Row Spacing:
-
Mounting Type:
立贴
Mfr. Part #:
1.25T-5P
Package:
SMD,P=1.25mm
Model Number:
1.25T-5P
Introduction
Product Overview
This specification covers the 1.25mm Pitch Bar Connectors (SMT) series. Designed for reliable electrical connections, these connectors are suitable for a wide range of applications requiring stable performance under various environmental conditions.
Product Attributes
- Main body material: LCP
- Terminal material: Copper
- Terminal surface treatment: Tin plated
Technical Specifications
| Item | Specification | Requirement |
|---|---|---|
| Ratings | ||
| Rated Voltage (MAX) | 50V | |
| Rated Current (MAX) [AC(virtual value)/DC] | 1.0A | |
| Ambient temperature Range | -25 +85 | |
| Performance - Electrical Performance | ||
| Contact Resistance | Mate applicable and measure by dry circuit, 20mV MAX, 10mA. | 20 m MAX |
| Insulation Resistance | Mate applicable and apply 500V DC between adjacent terminal or ground. | 500M MIN |
| Dielectric Strength | Mate applicable and apply 500V AC (virtual value) for 1 minute between adjacent terminal or ground. | No Breakdown |
| Performance - Mechanical Performance | ||
| Insertion and Withdrawal Force | Insert and extract applicable at the speed rate of 253mm/minute. | Insertion: 5 * n (N) MAX Withdrawal: 0.3 * n (N) MIN |
| Terminal Retention Force | Pull the terminal at the speed rate of 253mm per minute. | 10 N MIN |
| Performance - Environmental Performance and Others | ||
| Repeated Insertion and Withdrawal | Insertion and withdrawal actuator up to 20 cycles at the speed rate of less than 10 cycles/minute. | Contact Resistance: 60 m MAX |
| Temperature Rise | Carrying rated current load. (UL 498) | Temperature Rise: 30 MAX |
| Appearance (after Temperature Rise test) | No Damage | |
| Vibration | DC 1mA under energized state; vibration along XYZ three axes; amplitude 1.5mm; frequency 10-55-10Hz/min; duration 2 hours. | Discontinuity: 1 ms MAX. Appearance: No Damage |
| Shock | DC 1mA under energized state; 490m/s {50G} impact in 6 directions perpendicular to each other; 3 times each. | Discontinuity: 1 ms MAX. Appearance: No Damage |
| Heat Resistance | 852, 96 hours. | Contact Resistance: 60 m MAX Appearance: No Damage |
| Cold Resistance | -402, 96 hours. | Contact Resistance: 60 m MAX Appearance: No Damage |
| Dielectric Strength (after Cold Resistance test) | Must meet 4.1.3 | |
| Humidity | Temperature: 402, Relative Humidity: 90-95%, Duration: 96 Hours. Measured within 0.5 hours after returning to room temperature. | Insulation Resistance: 100 M MIN Appearance: No Damage |
| Temperature Cycling | 5 cycles of: a) -553 30 minutes, b) 852 30 minutes. Each phase followed by 10-15 minutes at normal temperature and humidity. | Contact Resistance: 60 m MAX Appearance: No Damage, Corrosion |
| Salt Spray | 484 hours exposure to a salt spray from the 51% solution at 352. Washed with room temperature water after test and dried at room temperature. | Contact Resistance: 60 m MAX |
| SO2 Gas Resistance | 24 hours exposure to 505ppm SO2 gas at 402. | Contact Resistance: 60 m MAX Appearance: No Damage |
| NH3 Gas Resistance | 40 minutes exposure to NH3 gas evaporating from 28% Ammonia solution. | Contact Resistance: 60 m MAX |
| Solder ability | Soldering Time: 20.5 sec. Soldering Temperature: 2355. Terminal tip immersed 0.2 mm from terminal tip. | Solder Wetting: 95% or more of the wetted area. |
| Resistance to Soldering Heat | Soldering Time: 305 sec. Soldering Temperature: 2605. Performed in a hot air oven. At least 5 times. | Appearance: No Damage, Deformation |
2512251656_BOOMELE-Boom-Precision-Elec-1-25T-5P_C37886.pdf
Related Products
BOOMELE Boom Precision Elec 1.25T 14AW 1.5mm thickness industrial component for technical application
Connector Header 14 position 1.25mm Pitch Right Angle
BOOMELE Boom Precision Elec HY-5P connector strip designed for consistent and electrical connections
Connector Header 5 position 2mm Pitch Surface Mount, Right Angle
BOOMELE Boom Precision Elec 1.25T-1-16A industrial component featuring 1.5mm thickness for technical
Connector Header 16 position 1.25mm Pitch
BOOMELE Boom Precision Elec 1.25T-1-13AW technical connector with accurate industrial specifications
Connector Header 13 position 1.25mm Pitch Right Angle
BOOMELE Boom Precision Elec XH-4A connector engineered for secure electrical connections in industry
Connector Header 4 position 2.5mm Pitch Through Hole
BOOMELE Boom Precision Elec 2510-5A electrical connectors terminal blocks and pin headers for wiring
Connector Header 5 position 2.54mm Pitch Right Angle
Electrical connector BOOMELE Boom Precision Elec 1.25T-13A featuring 1.5mm dimension for connectivity
Connector Header 13 position 1.25mm Pitch Through Hole
BOOMELE Boom Precision Elec PH 5AWD right angle and straight pin header connector housings for electrical
Connector Header 5 position 2mm Pitch Right Angle
wire to board connector BOOMELE Boom Precision Elec PHD-2 6AW with 2.0 millimeter pitch and lead free material
Connector Header 12 position 2mm Pitch Right Angle
Industrial electrical connector BOOMELE Boom Precision Elec 1.5-6A suitable for precise applications
Connector Header 6 position 1.5mm Pitch Through Hole
Send RFQ
Stock:
MOQ:
