0.5mm Pitch SMT Connector with Phosphor Bronze Terminals and UL94V-0 Housing CAX CAX-AFC01-45XCB-H2.0 Series
Manufacturer:
CAX
Description:
FFC/FPC Connector 45 Position 0.5mm Pitch Bottom Contact Surface Mount, Right Angle -25℃~+85℃
Category:
FFC, FPC (Flat Flexible) Connector Assemblies/FFC, FPC (Flat Flexible) Connector Housings
Specifications
Locking Feature:
翻盖式
Operating Temperature:
-25℃~+85℃
Number Of Contacts:
45P
Contact Type:
下接
FFC, FCB Thickness:
0.3mm
Pitch:
0.5mm
Mfr. Part #:
CAX-AFC01-45XCB-H2.0
Package:
SMD,P=0.5mm,Surface Mount,Right Angle
Model Number:
CAX-AFC01-45XCB-H2.0
Introduction
Product Overview
This specification covers the 0.5mm Pitch H=2.0 FPC Easy-on R/A SMT type connectors series. Designed for reliable connections, these connectors feature a LCP housing in white and a LCP actuator in black, both with a UL94V-0 flammability rating. The terminals and fitting nails are made of Phosphor Bronze. They are suitable for a wide operating temperature range of -55C to +85C and offer a maximum operating voltage of 50V AC and a current rating of 0.5A DC.
Product Attributes
- Brand: ZHE JIANG CHUANG DU ELECTRONICS CO.,LTD
- Product Type: 0.5mm Pitch H=2.0 FPC Easy-on R/A SMT type connectors series
- Housing Material: LCP
- Housing Color: White
- Housing Flammability Rating: UL94V-0
- Actuator Material: LCP
- Actuator Color: Black
- Actuator Flammability Rating: UL94V-0
- Terminal Material: Phosphor Bronze
- Fitting Nail Material: Phosphor Bronze
- Pitch: 0.5mm
- Height: 2.0mm
- Mounting Type: SMT (Surface Mount Technology)
- Actuator Type: Easy-on, Flip-cover ()
- Orientation: Right Angle (R/A)
Technical Specifications
| Item | Specifications | Test Condition |
|---|---|---|
| Operating Voltage (Max.) | 50V AC | |
| Current Rating (Max.) | 0.5A DC | *: Including terminal temperature rise. |
| Operating Temperature Range | -55C ~ +85C | |
| Operating Humidity Range | 90% RH Max. | Relative humidity 90% below |
| Storage Temperature Range | -10C ~ +50C | |
| Storage Humidity Range | 90% RH Max. | Relative humidity 90% below |
| Contact Resistance | 30 m Max. | Mate applicable FPC and measure by dry circuit, 20mV Max, 10mA. (EIA-364-23) |
| Insulation Resistance | 500 M Min. | Mate applicable FPC and apply 500V DC between adjacent terminal or ground. (EIA-364-21) |
| Dielectric Strength | No Breakdown | Mate applicable FPC, apply 250V AC(rms) for 1 minute between adjacent terminal or ground. (EIA-364-20) |
| FPC Retention Force | 0.30N Min. (per position) | Insert the actuator, pull the FPC at a rate of 253mm per minute. |
| Terminal Retention Force | 3N Min. | Apply axial pull out force at the rate of 253 mm/minute on the terminal assembled in the housing. |
| Fitting Nail Retention Force | 1.0N Min. | Apply axial pull out force at the rate of 253 mm/minute on the Fitting Nail assembled in the housing. |
| Durability (Contact Resistance) | 60 m Max. | Insert and withdraw actuator up to 20 cycles at the speed rate of less than 10 cycles/minute. |
| Temperature Rise | 30C Max. | Mate applicable FPC and measure the temperature rise of contact when the maximum AC rated current is passed. (EIA-364-70 METHOD 2) |
| Vibration (Contact Resistance) | 60 m Max. | Mate connectors and subject to vibration conditions (1.5mm P-P, 10~55~10 Hz, 2 hours in each of X,Y,Z axes, passing DC 1mA). (EIA-364-28 Condition I) |
| Vibration (Discontinuity) | 1sec Max. | Mate connectors and subject to vibration conditions (1.5mm P-P, 10~55~10 Hz, 2 hours in each of X,Y,Z axes, passing DC 1mA). (EIA-364-28 Condition I) |
| Shock (Contact Resistance) | 60 m Max. | Mate applicable FPC and subject to shock conditions (490m/s2 {50G}, 3 times in each of 6 directions, passing DC 1mA). (EIA-364-27, test condition A) |
| Shock (Discontinuity) | 1sec Max. | Mate applicable FPC and subject to shock conditions (490m/s2 {50G}, 3 times in each of 6 directions, passing DC 1mA). (EIA-364-27, test condition A) |
| Heat Resistance (Contact Resistance) | 60 m Max. | Mate applicable FPC and expose to 852C for 96 hours. Condition at ambient room for 1-2 hours. |
| Cold Resistance (Contact Resistance) | 60 m Max. | Mate applicable FPC and expose to -402C for 96 hours. Condition at ambient room for 1-2 hours. |
| Humidity (Contact Resistance) | 60 m Max. | Mate applicable FPC and expose to 602C, 90-95% RH for 96 hours. Condition at ambient room for 1-2 hours. |
| Humidity (Dielectric Strength) | No Breakdown | Mate applicable FPC and expose to 602C, 90-95% RH for 96 hours. Condition at ambient room for 1-2 hours. |
| Humidity (Insulation Resistance) | 30 M Min. | Mate applicable FPC and expose to 602C, 90-95% RH for 96 hours. Condition at ambient room for 1-2 hours. |
| Temperature Cycling (Contact Resistance) | 60 m Max. | Mate applicable FPC and subject to 5 cycles of -553C (30 min) and +853C (30 min). Condition at ambient room for 1-2 hours. |
| Salt Spray (Contact Resistance) | 60 m Max. | Mate applicable FPC and expose to 51% NaCl solution at 352C for 484 hours. Wash with clean water and dry. |
| SO2 Gas (Contact Resistance) | 60 m Max. | Mate applicable FPC and expose to SO2 gas (505 ppm) at 402C for 24 hours. |
| NH3 Gas (Contact Resistance) | 60 m Max. | 40 minutes exposure to NH3 gas evaporating from 28% Ammonia solution. |
| Solderability (Wetting) | 75% of immersed area must show no voids, pin holes. | Tip of solder tails and fitting nails into molten solder (2455C) up to 0.1mm from housing bottom for 30.5 seconds. |
| Resistance to Soldering Heat (Soldering Iron) | No Damage | 0.2mm from terminal tip and fitting nail tip. Soldering time: 5 seconds Max. Solder temperature: 370~400C. |
Infrared Reflow Condition:
Temperature on Board Pattern Side:
- Pre-Heat: Start (150C MAX.)
- Soak: 60~90 seconds
- Reflow: 230C MIN. / 20~40 seconds, 250C MAX. (Peak Temp) 3 seconds or less
Instruction upon usage of ZIF Easy-On Type:
- Use thumb or forefinger to raise the top cover upwards.
- Insert FPC with conductive fingers facing down, parallel to the connector.
- Press the top cover lightly and rotate down until FPC is fully inserted and secured.
- To withdraw FPC, carefully lift the top cover and slide out the FPC.
Warnings:
- Rotation angle of the cover should not exceed 120 degrees.
- Inserting FPC at an excessive angle may cause electrical discontinuity.
- Upward pulling force should not exceed 0.04N/pin max.
- Do not use excessive force when opening the connector cover to avoid touching the terminals.
2507091655_CAX-CAX-AFC01-45XCB-H2-0_C49272723.pdf
Related Products
electronic component CAX CAX-AFC11-04ICB-H4.4 designed for precise industrial applications
FFC/FPC Connector 4 Position 0.5mm Pitch Single-side Contact/Vertical Surface Mount -25℃~+85℃
1.0mm Pitch FPC Easyon Right Angle SMT Connector CAX CAX-A01-10XCB-H2.0 for Electronic Applications
-55℃~+85℃ Hinged Lid 10P Bottom Contact 1mm SMD,P=1mm,Surface Mount,Right Angle FFC, FPC (Flat Flexible) Connector Housings RoHS
0.5mm Pitch H2.0 FPC Easy On SMT Connectors CAX CAX AFC01 34XCB H2.0 with Phosphor Bronze Terminals
FFC/FPC Connector 34 Position 0.5mm Pitch Bottom Contact Surface Mount, Right Angle -25℃~+85℃
Electronic connector CAX CAX-AFC11-14ICB-H4.4 designed for industrial applications and reliability
FFC/FPC Connector 14 Position 0.5mm Pitch Single-side Contact/Vertical Surface Mount -25℃~+85℃
Robust and CAX CAX-AFC11-30ICB-H4.4 electronic part suitable for technical projects requiring precision
FFC/FPC Connector 30 Position 0.5mm Pitch Single-side Contact/Vertical Surface Mount -25℃~+85℃
1.0mm Pitch FPC FFC ZIF R A Type K SMT Connectors CAX CAX AFA07 14SCB H2.5 for Electronic Applications
FFC/FPC Connector 14 Position 1mm Pitch Top Contact Surface Mount, Right Angle -25℃~+85℃
CAX CAX A07 15SCB H2.5 compact 1.0mm pitch H2.5 FPC FFC ZIF R A type K SMT connectors with LCP housing
Slide Lock -55℃~+85℃ 15P Top Contact 1mm SMD,P=1mm,Surface Mount,Right Angle FFC, FPC (Flat Flexible) Connector Housings RoHS
CAX CAX AFC01 13XCB H2 0 0.5mm Pitch H 2.0 FPC Easy On R A SMT Connectors for Low Voltage Applications
FFC/FPC Connector 13 Position 0.5mm Pitch Bottom Contact Surface Mount, Right Angle -25℃~+85℃
2.0mm Height FPC ZIF SMT Connector with 0.5mm Pitch CAX CAX-AFC07-10SCB-H2.0 Right Angle Upper Type
FFC/FPC Connector 10 Position 0.5mm Pitch Top Contact Surface Mount, Right Angle -25℃~+85℃
Durable industrial connector CAX CAX-AFC11-26ICB-H4.4 suitable for electronic system integration
FFC/FPC Connector 26 Position 0.5mm Pitch Single-side Contact/Vertical Surface Mount -25℃~+85℃
| Image | Part # | Description | |
|---|---|---|---|
|
|
electronic component CAX CAX-AFC11-04ICB-H4.4 designed for precise industrial applications |
FFC/FPC Connector 4 Position 0.5mm Pitch Single-side Contact/Vertical Surface Mount -25℃~+85℃
|
|
|
|
1.0mm Pitch FPC Easyon Right Angle SMT Connector CAX CAX-A01-10XCB-H2.0 for Electronic Applications |
-55℃~+85℃ Hinged Lid 10P Bottom Contact 1mm SMD,P=1mm,Surface Mount,Right Angle FFC, FPC (Flat Flexible) Connector Housings RoHS
|
|
|
|
0.5mm Pitch H2.0 FPC Easy On SMT Connectors CAX CAX AFC01 34XCB H2.0 with Phosphor Bronze Terminals |
FFC/FPC Connector 34 Position 0.5mm Pitch Bottom Contact Surface Mount, Right Angle -25℃~+85℃
|
|
|
|
Electronic connector CAX CAX-AFC11-14ICB-H4.4 designed for industrial applications and reliability |
FFC/FPC Connector 14 Position 0.5mm Pitch Single-side Contact/Vertical Surface Mount -25℃~+85℃
|
|
|
|
Robust and CAX CAX-AFC11-30ICB-H4.4 electronic part suitable for technical projects requiring precision |
FFC/FPC Connector 30 Position 0.5mm Pitch Single-side Contact/Vertical Surface Mount -25℃~+85℃
|
|
|
|
1.0mm Pitch FPC FFC ZIF R A Type K SMT Connectors CAX CAX AFA07 14SCB H2.5 for Electronic Applications |
FFC/FPC Connector 14 Position 1mm Pitch Top Contact Surface Mount, Right Angle -25℃~+85℃
|
|
|
|
CAX CAX A07 15SCB H2.5 compact 1.0mm pitch H2.5 FPC FFC ZIF R A type K SMT connectors with LCP housing |
Slide Lock -55℃~+85℃ 15P Top Contact 1mm SMD,P=1mm,Surface Mount,Right Angle FFC, FPC (Flat Flexible) Connector Housings RoHS
|
|
|
|
CAX CAX AFC01 13XCB H2 0 0.5mm Pitch H 2.0 FPC Easy On R A SMT Connectors for Low Voltage Applications |
FFC/FPC Connector 13 Position 0.5mm Pitch Bottom Contact Surface Mount, Right Angle -25℃~+85℃
|
|
|
|
2.0mm Height FPC ZIF SMT Connector with 0.5mm Pitch CAX CAX-AFC07-10SCB-H2.0 Right Angle Upper Type |
FFC/FPC Connector 10 Position 0.5mm Pitch Top Contact Surface Mount, Right Angle -25℃~+85℃
|
|
|
|
Durable industrial connector CAX CAX-AFC11-26ICB-H4.4 suitable for electronic system integration |
FFC/FPC Connector 26 Position 0.5mm Pitch Single-side Contact/Vertical Surface Mount -25℃~+85℃
|
Send RFQ
Stock:
MOQ:
