Electrical connector strip 2.00 series with white PBT UL94V-O housing and phosphor bronze terminals HCTL HC-JWPF-2x3SY-05
Manufacturer:
HCTL
Description:
Connector Housing 6 Position 2mm Pitch Dual Row JWPF Series PBT -25℃~+85℃
Category:
Arrays, Edge Type, Mezzanine (Board to Board)/Rectangular Connector Housings
Specifications
Flame Retardant Rating:
-
Pitch:
2mm
Colour:
白色
Number Of Rows:
2
With Wings:
不带翅
Reference Series:
JWPF
Operating Temperature:
-25℃~+85℃
Plastic Material:
PBT
Number Of PINs Per Row:
3
Number Of Positions Or Pins:
2x3P
With Locker:
不带锁扣
Row Spacing:
4mm
Mfr. Part #:
HC-JWPF-2x3SY-05
Package:
P=2mm
Model Number:
HC-JWPF-2x3SY-05
Introduction
Product Overview
This specification covers the 2.00 series JWPF connector strip, detailing its performance, test methods, and inspection requirements. It is designed for use in various electrical equipment applications.
Product Attributes
- Brand: HCTLDZ ()
- Origin: Shenzhen, China
- Certifications: ROHS
- Material: Phosphor bronze (Terminal), PBT UL94V-O(2) (Housing)
- Color: White (Housing)
Technical Specifications
| Item | Specification | Test Method | |||
| 1. Scope | |||||
| This specification applies to the 2.00 series connector strip, including product performance, test methods, and inspection requirements. | |||||
| 2. Applicable Standards | |||||
| 2.1 | GB/T2421 Environmental Testing for Electrical Connectors - Part 1: General Principles | ||||
| 2.2 | GB/T2423 Environmental Testing for Electrical Connectors | ||||
| 2.3 | GB/T2424 Environmental Testing for Electrical Connectors | ||||
| 2.4 | GB/T5095 Testing Procedure/Method for Components of Electric Equipment | ||||
| 3. Use Condition | |||||
| 3.1 Ambient Temperature Range | -25 85 | ||||
| 3.2 Applicable Wire Sizes | AWG #2226 | ||||
| 3.3 Applicable PC board thickness | 0.8l.6mm | ||||
| 4. Appearance and Dimension | |||||
| 4.1 Appearance | Product surface without defect, dirt, crack, and mechanical damage; Contact without rust, plating oxidation, peeling off etc. | ||||
| 4.2 Dimension | According to drawings | ||||
| 4.3 Exchangeable | Exchangeable with same specification products. | ||||
| 5. Material | |||||
| No. | P/N | Type | Explain | Material | Finish |
| 5.1 | Terminal Contact | Phosphor bronze (0.2mm thick) | Tin plating: 35 m | ||
| 5.2 | Terminal Contact | Phosphor bronze (0.2mm thick) | Tin plating: 35 m | ||
| 5.3 | Housing Plastic | -Y | PBT UL94V-O(2) | Color: White | |
| 5.4 | Housing Plastic | -SY | PBT UL94V-O(2) | Color: White | |
| 6. Electrical Performance | |||||
| Item | Rated Voltage | Rated Current | Requirement | Test Mode | |
| Contact Resistance | 3A (AC/DC) | Initial value 20m | Apply 1000V AC(rms) for 1 minute and the leakage current shall not exceed 0.5mA to the adjacent terminal and ground of the mate connectors. Does not include wire resistance. | ||
| Insulation Resistance | 100V (AC/DC) | lOOOM | Apply 500V DC(rms) for 1 minute between adjacent contacts to measure the insulation resistance. | ||
| Withstand voltage | No breakdown or flashover | A maximum voltage of 20mV and maximum current of 100mA are applied to the mate connector. | |||
| 7. Mechanical Performance | |||||
| Item | Requirement | Test Mode | |||
| Single contact insertion force | 5N | Housing together with terminal ends with wafer matched at a rate per minute to 253mm inserting force test. | |||
| Terminal and hole seat fixed force | 15N | The terminal and the hole seat at a rate per minute to 253mm along the write direction are pulled out from the hole in the seat capacity. | |||
| Single contact Withdrawal force | 0.5N | ||||
| Terminal crimping Wire strength | AWG#22: 15N, AWG#24: 30N, AWG#26: 20N | Axial per minute to 25 3mm rate of the pullout force. | |||
| Pin Retention Force | 50N | Exerts a force on the pin end at a rate per minute 253mm until the needle exit Seat pull-out force. | |||
| Vibration | Current Interruption: 1 sec Max Contact Resistance 40m Appearance: No damage | Amplitude: 1.5mm p-p, Frequency: 10-55-10 Hz/minute, Period: 2 hours for each direction (X, Y, Z axis). | |||
| Durability | Contact Resistance 40m Appearance: No damage | Mate connectors up 30 cycles at a Maximum rate of 10 cycles per minute prior to environmental test. | |||
| 8. Endurance Characteristics | |||||
| Item | Requirement | Test Mode | |||
| Thermal Aging | Contact Resistance 40m Appearance: No damage | Temperature: 852, Period: 96 hours continuously. | |||
| Temperature Rise | Mate connector measure the temperature rise of contact when the maximum rated current is passed. | ||||
| Constant Humidity | Contact Resistance 40m Insulation Resistance 1000m Appearance: No damage | Temperature: 402 C, Relative humidity: 90-95% (RH), Period: 96 hours continuously. | |||
| Temperature Cycling | No breakdown or flashover | One cycle: -553C 30min, room temp 10-15min, then 853C 30min, room temp 10-15min. Total cycle: 5 cycles. | |||
| Salt Spray | Contact Resistance 40m Appearance: No damage | Solution: 51% Salt, Temperature: 353 C. Stamping after tin plated for 8 hours, Stamping before tin plated for 48 hours. | |||
| 9. Packaging Transportation Storage | |||||
| 9.1 Packaging | Terminal: disc loading material. Housing: plastic shell packaging for plastic has seat plates tubes mounted (paste). Exterior: carton. Product in the box must not rock. | Certificate indicating product name, specifications, quantity, production date. Packing list marked with product name, specification, model, quantity, date of dispatch. | |||
| 9.2 Transportation | Any vehicle can be adopted for the transportation but moisture-proof and no mechanical damage. | ||||
| Storage | Store in a warehouse with ambient temperature of -20 +40, relative humidity 80%, and no corrosive gases. Re-qualification test shall be conducted immediately while the storing duration exceed 6 months. | ||||
2403071456_HCTL-HC-JWPF-2x3SY-05_C7543256.pdf
Related Products
Connector HC-1.0-9Y with 8 millimeter A and 12 millimeter B dimensions manufactured from NY material
Connector Housing 9 Position 1mm Pitch Single Row SH Series PBT -25℃~+85℃
HC-XA-5Y component offering 10 millimeter dimension designed for precision and long-lasting industrial
Connector Housing 5 Position 2.5mm Pitch Single Row XA Series PA66 -25℃~+85℃
5.08mm Pitch Double Row Connector Suitable for AWG 14 to 24 PC Board Thickness 16mm HCTL HC 508D 3Y 05
Connector Housing 3 Position 5.08mm Pitch Single Row PBT -25℃~+85℃
Electrical Connector Double Row 2.00mm Pitch HCTL HC-PHB-2*14Y-05 Ideal for Electronic and Electrical
Connector Housing 28 Position 2mm Pitch Dual Row PA66 -25℃~+85℃
| Image | Part # | Description | |
|---|---|---|---|
|
|
Connector HC-1.0-9Y with 8 millimeter A and 12 millimeter B dimensions manufactured from NY material |
Connector Housing 9 Position 1mm Pitch Single Row SH Series PBT -25℃~+85℃
|
|
|
|
HC-XA-5Y component offering 10 millimeter dimension designed for precision and long-lasting industrial |
Connector Housing 5 Position 2.5mm Pitch Single Row XA Series PA66 -25℃~+85℃
|
|
|
|
5.08mm Pitch Double Row Connector Suitable for AWG 14 to 24 PC Board Thickness 16mm HCTL HC 508D 3Y 05 |
Connector Housing 3 Position 5.08mm Pitch Single Row PBT -25℃~+85℃
|
|
|
|
Electrical Connector Double Row 2.00mm Pitch HCTL HC-PHB-2*14Y-05 Ideal for Electronic and Electrical |
Connector Housing 28 Position 2mm Pitch Dual Row PA66 -25℃~+85℃
|
Send RFQ
Stock:
MOQ:
