XLR jack combo connector JINJIA XLR-26A-7P-N3B rated for 3A and 7.5A current electronic applications
Manufacturer:
JINJIA
Description:
Through Hole Circular Connector Assemblies RoHS
Category:
Circular Connector Assemblies/Circular Connector Assemblies
Specifications
Mfr. Part #:
XLR-26A-7P-N3B
Package:
Through Hole
Model Number:
XLR-26A-7P-N3B
Introduction
XLR JACK (Combo) SPECIFICATION
This specification applies to XLR jack (Combo) which is used in electronic products. It details the electrical, mechanical, and environmental performance characteristics of the connector.
Product Attributes
- Brand: Shenzhen jinjiarun Electronic Technology Co., Ltd
- Origin: China
- Model: XLR JACK (Combo)
- Document Number: JJR-WI-46
- Issue Date: 2008-09-10
- Version: A1
Technical Specifications
| Item | Property | Test Condition | Performance |
| 2. Rated / | Practical temperature range | -30 to +80 | |
| Humidity range | 85% RH.MAX. | ||
| Preservation temperature range | -10 to +40 | ||
| Humidity range (Preservation) | 85% RH.MAX. | ||
| Storage conditions | Around air without acid, alkaline or other corrosive gases. Storage period not exceed 180 days. | ||
| Rated voltage and current (MAX.) | Type A: 50V AC, 3A | ||
| Rated voltage and current (MAX.) | Type B: 50V AC, 7.5A | ||
| 2-4. Appearance | Surface condition | No scratches, soil, rust or discoloration. | |
| 4. Electrical efficiency / | Withstand Voltage | AC 1500V (50/60Hz RMS) between two non-contact terminals for 1 minute. No dielectric breakdown shall occur. | |
| Insulation Resistance | Apply 500V DC between any contactless terminal and the other terminal, for 1 minute 5 seconds. | 10000 M Min. | |
| Contact Resistance | Measure at the tail end of each terminal (voltage max 20mV, current max 100mA) for a pair of matched terminals. | 30 m MAX. | |
| 5. Mechanical Performance / | Insertion and withdrawal forces | Rate of insertion/withdrawal: 2 mm/s. Mating of complete connectors without the effect of any latching or retaining device. | XLR: Insertion: 35 N max. Withdrawal: 2 N min. JACK: Insertion: 40 N max. Withdrawal: 5 N min. |
| Terminal Strength | Each terminal should withstand a force of 0.5 kgf for 10 seconds. | No looseness, damage, etc. Terminal deformation is acceptable. | |
| 6. Durability / | Life test | Under no load condition, rotate and then plug in, rotate and then pull out with a matching plug for 1000 times in total, at a frequency of 5 times per minute. | No obvious change in appearance, destruction. Contact resistance: less than 50 m. |
| 7. Solderability / | Resistance to soldering heat | Terminal dipped in solder: Temperature: 2603. Dip time: 51 seconds. | Plastic base should not be deformed and terminals should not fall off. |
| Solderability | Solder temperature: 2453C. Time of dip: 30.5 seconds. | Coating of solder area should be more than 95%. | |
| 8. Environment test / | Cold test | Housing placed at -30 3 C for 96 hours, then under standard atmospheric conditions for 1 hour and tested. | No obvious change in appearance. Contact resistance: 50 m max. Insulation resistance: 500 M min. Withstand voltage: AC 1000V. |
| Heat test | Housing stored at 802 for 96 hours, then under standard atmospheric conditions for 1 hour and tested. | ||
| Humidity test | Housing stored at 403 with relative humidity of 90% ~ 95% for 96 h, then under standard atmospheric conditions for 1 hour and tested. | No obvious change in appearance. Contact resistance: 50m max. Insulation resistance: 500 M min. Withstand voltage: AC 1000V. | |
| Temperature Cycling | Jack placed under specified conditions, then at room temperature for 30 minutes. | ||
| Salt spray test | Temperature: 35 2. Solution: 5 1%. Spray time: 24 hours. Washed and dried at room temperature after experiment. | No obvious rust in the appearance. | |
| 9. Test condition / | Standard conditions | Test and measurement temperature: 15C to 35C, relative humidity: 25% to 85%, atmospheric pressure: 86 kPa to 106 kPa. | |
| Doubtful condition | Test and measurement at 201C, relative humidity 63% to 67%, and air pressure 86 kPa to 106 kPa. |
2411220125_JINJIA-XLR-26A-7P-N3B_C558596.pdf
Related Products
electronic connector JINJIA XLR-19-6P designed to meet strict environmental and durability standards
Through Hole Circular Connector Assemblies RoHS
Durable XLR jack combo JINJIA XLR-19P-10P designed for stable audio connections in electronic devices
Through Hole Circular Connector Assemblies RoHS
electrical JINJIA XLR-26A-10P XLR jack combo connector rated voltage 50V AC 3A and 7.5A for electronic
Through Hole Circular Connector Assemblies RoHS
Speaker socket connection XLR jack combo JINJIA XLR-11W-N3B ideal for electronic device applications
Through Hole Circular Connector Assemblies RoHS
Durable JINJIA XLR-19P-7P XLR jack connector designed for stable electrical and mechanical performance
Through Hole Circular Connector Assemblies RoHS
XLR jack connector JINJIA XLR-14-N3B designed for stable performance in electronic product applications
Through Hole Circular Connector Assemblies RoHS
Electronic XLR Jack Connector JINJIA XLR-15-N3GR Rated Voltage 50V AC And Current 6A For Industrial
Through Hole Circular Connector Assemblies RoHS
Electronic connector JINJIA XLR-26AP-10P optimized for dependable audio signal performance in devices
Through Hole Circular Connector Assemblies RoHS
electrical connector JINJIA XLR-25-N3B rated 50V AC 6A operating temperature range minus 30 to plus 80 degrees
Through Hole Circular Connector Assemblies RoHS
electronic connector JINJIA XLR-15-N3G featuring corrosion resistant surface and humidity resistance
Through Hole Circular Connector Assemblies RoHS
Send RFQ
Stock:
MOQ:
