electrical JINJIA XLR-26A-10P XLR jack combo connector rated voltage 50V AC 3A and 7.5A for electronic
Manufacturer:
JINJIA
Description:
Through Hole Circular Connector Assemblies RoHS
Category:
Circular Connector Assemblies/Circular Connector Assemblies
Specifications
Mfr. Part #:
XLR-26A-10P
Package:
Through Hole
Model Number:
XLR-26A-10P
Introduction
Product Overview
This specification applies to XLR jack (Combo) connectors used in electronic products. It details the electrical, mechanical, and environmental performance requirements for these connectors.
Product Attributes
- Brand: Jinjiarun
- Origin: Shenzhen, China
Technical Specifications
| Item | Property | Test Condition | Performance |
| 2. Rated / | |||
| Practical temperature range | -30 to +80 | ||
| Humidity range | 85% RH.MAX. | ||
| Preservation temperature range | -10 to +40 | ||
| Preservation humidity range | 85% RH.MAX. | ||
| Storage environment | Around air without acid, alkaline or other corrosive gases. Storage period not exceed 180 days. | ||
| Rated voltage and current (MAX.) | 50V AC, 3A (Type A) | ||
| Rated voltage and current (MAX.) | 50V AC, 7.5A (Type B) | ||
| Appearance | No scratches, soil, rust or discoloration on the surface. | ||
| 4. Electrical efficiency / | |||
| Withstand Voltage | Withstand AC 1500V (50/60Hz RMS) between two non-contact terminals for 1 minute. No dielectric breakdown shall occur. | Between two non-contact terminals | No dielectric breakdown |
| Insulation Resistance | 10000 M Min. | Apply 500V DC between any contactless terminal and the other terminal, with an insulation gauge and last for 1 minute 5 seconds. | 10000 M Min. |
| Contact Resistance | 30 m MAX. | Take a pair of matched terminals and measure the tail end of each terminal (voltage maximum 20mV, current maximum 100mA). | 30 m MAX. |
| 5. Mechanical Performance / | |||
| Insertion and withdrawal forces | XLR: Insertion: 35 N max. Withdrawal: 2 N min. | Rate of insertion/withdrawal: 2 mm/s. Mating of complete connectors without the effect of any latching or retaining device. | |
| Insertion and withdrawal forces | JACK: Insertion: 40 N max. Withdrawal: 5 N min. | Rate of insertion/withdrawal: 2 mm/s. Mating of complete connectors without the effect of any latching or retaining device. | |
| Terminal Strength | No looseness, damage, etc., but terminal deformation is acceptable. | Every terminal should be capable of withstand a force of 0.5 kgf for 10 seconds. | No looseness, damage, etc. |
| 6. Durability / | |||
| Life test | Appearance: No obvious change, destruction. Contact resistance: less than 50 m. | Under no load, rotate and then plug in, rotate and then pull out with a matching plug for 1000 times in total, at a frequency of 5 times per minute. | Contact resistance < 50 m |
| 7. Solderability / | |||
| Resistance to soldering heat | After the test, the plastic base should not be deformed and the terminals should not fall off the plastic base. | The jack terminal should be dipped in solder: Temperature of solder: 2603. Dip time: 51 seconds. | No deformation, no terminal detachment |
| Solderability | Coating of solder area should be more than 95% | Temperature of solder: 2453C. Time of dip: 30.5 seconds. | >95% solder coverage |
| 8. Environment test / | |||
| Cold test | Appearance: No obvious change. Contact resistance: 50 m max. Insulation resistance: 500 M min. Withstand voltage: AC 1000V. | Place the housing for 96 hours at -30 3 C. Then, place under standard atmospheric conditions for 1 hour and test. | |
| Heat test | The housing should be stored at 802 for 96 hours. Then, subject to standard atmospheric conditions for 1 hour and test. | ||
| Humidity test | Appearance: No obvious change. Contact resistance: 50m max. Insulation resistance: 500 M min. Withstand voltage: AC 1000V. | Stored at 403 with relative humidity of 90% ~ 95% for 96 h. Then, subject to standard atmospheric conditions for 1 hour and test. | |
| Salt spray test | No obvious rust in the appearance. | Temperature: 35 2. Solution: 5 1%. Spray time: 24hours. Wash and dry at room temperature after the experiment. | No obvious rust |
| 9. Test condition / | |||
| Standard conditions | Test and measurement temperature: 15C to 35C, relative humidity: 25% to 85%, atmospheric pressure: 86 kPa to 106 kPa. | ||
| Doubtful conditions | Test and measurement temperature: 201C, relative humidity: 63% to 67%, atmospheric pressure: 86 kPa to 106 kPa. | ||
| 12. XLR JACK (Combo) TYPE /XLR | |||
| Type A | Rated current: 3A | ||
| Type B | Rated current: 7.5A | ||
2411220316_JINJIA-XLR-26A-10P_C558597.pdf
Related Products
electronic connector JINJIA XLR-19-6P designed to meet strict environmental and durability standards
Through Hole Circular Connector Assemblies RoHS
Durable XLR jack combo JINJIA XLR-19P-10P designed for stable audio connections in electronic devices
Through Hole Circular Connector Assemblies RoHS
Speaker socket connection XLR jack combo JINJIA XLR-11W-N3B ideal for electronic device applications
Through Hole Circular Connector Assemblies RoHS
Durable JINJIA XLR-19P-7P XLR jack connector designed for stable electrical and mechanical performance
Through Hole Circular Connector Assemblies RoHS
XLR jack connector JINJIA XLR-14-N3B designed for stable performance in electronic product applications
Through Hole Circular Connector Assemblies RoHS
XLR jack combo connector JINJIA XLR-26A-7P-N3B rated for 3A and 7.5A current electronic applications
Through Hole Circular Connector Assemblies RoHS
Electronic XLR Jack Connector JINJIA XLR-15-N3GR Rated Voltage 50V AC And Current 6A For Industrial
Through Hole Circular Connector Assemblies RoHS
Electronic connector JINJIA XLR-26AP-10P optimized for dependable audio signal performance in devices
Through Hole Circular Connector Assemblies RoHS
electrical connector JINJIA XLR-25-N3B rated 50V AC 6A operating temperature range minus 30 to plus 80 degrees
Through Hole Circular Connector Assemblies RoHS
electronic connector JINJIA XLR-15-N3G featuring corrosion resistant surface and humidity resistance
Through Hole Circular Connector Assemblies RoHS
Send RFQ
Stock:
MOQ:
