Audio Signal Connector JINJIA XLR-20 Rated Voltage 250V AC and Current 15A for Continuous Electronic
Manufacturer:
JINJIA
Description:
Through Hole Circular Connector Assemblies RoHS
Category:
Circular Connector Assemblies/Circular Connector Assemblies
Specifications
Mfr. Part #:
XLR-20
Package:
Through Hole
Model Number:
XLR-20
Introduction
Product Overview
This specification applies to XLR jack (SPEAKON) connectors used in electronic products. They are designed for audio signal applications and are not to be used as AC mains or power supply connectors.
Product Attributes
- Brand: Shenzhen Jinjiarun Electronic Technology Co., Ltd
- Origin: China
- Model: XLR JACK (SPEAKON)
- Document Number: JJR-WI-48
- Issue Date: 2008-09-10
- Version: A1
Technical Specifications
| Item | Property | Test Condition | Performance |
| 2.Rated / | Practical temperature range | -30to +80 | |
| Humidity range | 85% RH.MAX. | ||
| Preservation temperature range | -10to +40 | ||
| Preservation Humidity range | 85% RH.MAX. | ||
| Storage Conditions | Surrounding air without acid, alkaline or other corrosive gases. Storage period not exceeding 180 days. | ||
| Rated voltage and current (MAX.) | 250V AC , 15A (continuous) | ||
| Audio signal rating | 30 A, duty cycle 50 % | ||
| 2-4. Appearance | No scratches, soil, rust or discoloration on the surface. | ||
| 3-1. Outline And Dimension | Should match the attachment drawing. | ||
| 3-2. Part And Material | Should be consistent with the material list specifications. | ||
| 4. Electrical efficiency | Withstand Voltage | Withstand AC 4000V (50/60Hz RMS) between two non-contact terminals for 1 minute. | No dielectric breakdown shall occur. |
| Insulation Resistance | Apply 500V DC between any contactless terminal and the other terminal, with an insulation gauge and last for 1 minute 5 seconds. | 1000 M Min. | |
| Contact Resistance | Take a pair of matched terminals and measure the tail end of each terminal (voltage maximum 20mV, current maximum 100mA). | 30 m MAX. | |
| 5. Mechanical Performance | Terminal Strength | Every terminal should be capable of withstand a force of 0.5 kgf for 10 seconds. | No looseness, damage, etc., but terminal deformation is acceptable. |
| 6. Durability | Life test | Under no load condition, plug in and rotate, pull out and rotate with a matching plug for 5000 times in total, at a frequency of 5 times per minute. | Appearance with no obvious change, no destruction. Contact resistance: less than 50 m. |
| 7. Solderability | Resistance to soldering heat | Jack terminal dipped in solder: Temperature of solder: 2603. Dip time: 51 seconds. | After test, the plastic base should not be deformed and the terminals should not fall off the plastic base. |
| Solderability | Temperature of solder: 2453C. Time of dip: 30.5 seconds. | Coating of solder area should be more than 95%. | |
| 8. Environment test | Cold test | Housing placed for 96 hours at -30 3 C. Then, placed under standard atmospheric conditions for 1 hour and tested. | No obvious change in appearance. Contact resistance: 50 m max. Insulation resistance: 500 M min. Withstand voltage: AC 1000V. |
| Heat test | Housing stored at 802 for 96 hours. Then subjected to standard atmospheric conditions for 1 hour and tested. | ||
| Humidity test | Housing stored at 403 with relative humidity of 90% ~ 95% for 96 h. Then subjected to standard atmospheric conditions for 1 hour and tested. | No obvious change in appearance. Contact resistance: 50m max. Insulation resistance: 500 M min. Withstand voltage: AC 1000V. | |
| Temperature Cycling | Conditions as shown in the document, then placed at room temperature for 30 minutes. | ||
| Salt spray test | Temperature: 35 2. Solution: 5 1%. Spray time: 24 hours. Washed and dried at room temperature after experiment. | No obvious rust in the appearance. | |
| 9. Test condition | Standard conditions | Test and measurement temperature is between 15 C and 35 C, relative humidity is between 25% and 85%, atmospheric pressure is between 86 kPa and 106 kPa. | For judgment doubts: 201 C, relative humidity 63% to 67%, air pressure 86 kPa to 106 kPa. |
| 10. Amendment | Specification changes | Must be negotiated and agreed by the manufacturer and the customer before proceeding. |
2411220155_JINJIA-XLR-20_C558743.pdf
Related Products
electronic connector JINJIA XLR-19-6P designed to meet strict environmental and durability standards
Through Hole Circular Connector Assemblies RoHS
Durable XLR jack combo JINJIA XLR-19P-10P designed for stable audio connections in electronic devices
Through Hole Circular Connector Assemblies RoHS
electrical JINJIA XLR-26A-10P XLR jack combo connector rated voltage 50V AC 3A and 7.5A for electronic
Through Hole Circular Connector Assemblies RoHS
Speaker socket connection XLR jack combo JINJIA XLR-11W-N3B ideal for electronic device applications
Through Hole Circular Connector Assemblies RoHS
Durable JINJIA XLR-19P-7P XLR jack connector designed for stable electrical and mechanical performance
Through Hole Circular Connector Assemblies RoHS
XLR jack connector JINJIA XLR-14-N3B designed for stable performance in electronic product applications
Through Hole Circular Connector Assemblies RoHS
XLR jack combo connector JINJIA XLR-26A-7P-N3B rated for 3A and 7.5A current electronic applications
Through Hole Circular Connector Assemblies RoHS
Electronic XLR Jack Connector JINJIA XLR-15-N3GR Rated Voltage 50V AC And Current 6A For Industrial
Through Hole Circular Connector Assemblies RoHS
Electronic connector JINJIA XLR-26AP-10P optimized for dependable audio signal performance in devices
Through Hole Circular Connector Assemblies RoHS
electrical connector JINJIA XLR-25-N3B rated 50V AC 6A operating temperature range minus 30 to plus 80 degrees
Through Hole Circular Connector Assemblies RoHS
Send RFQ
Stock:
MOQ:
