Durable XLR Jack Connector JINJIA XLR-18P-3-N3B Rated Voltage 50V AC Current 6A Suitable for Electronic Products
Manufacturer:
JINJIA
Description:
Through Hole Circular Connector Assemblies RoHS
Category:
Circular Connector Assemblies/Circular Connector Assemblies
Specifications
Mfr. Part #:
XLR-18P-3-N3B
Package:
Through Hole
Model Number:
XLR-18P-3-N3B
Introduction
XLR JACK SPECIFICATION
This specification applies to XLR jacks used in electronic products. It details the electrical, mechanical, durability, and environmental performance requirements for these connectors.
Product Attributes
- Brand: Shenzhen jinjiarun Electronic Technology Co., Ltd
- Origin: China
- Document Number: JJR-WI-47
- Issue Date: 2008-09-10
- Version: A1
Technical Specifications
| Item | Property | Test Condition | Performance |
|---|---|---|---|
| 2. Rated / | Practical temperature range | -30 to +80 | |
| Humidity range (Practical) | 85% RH.MAX. | ||
| Preservation temperature range | -10 to +40 | ||
| Humidity range (Preservation) | 85% RH.MAX. | ||
| Rated voltage and current (MAX.) | 50V AC , 6A | ||
| Appearance | No scratches, soil, rust or discoloration on the surface. | ||
| 4. Electrical efficiency / | Withstand Voltage | Withstand AC 1500V (50/60Hz RMS) between two non-contact terminals for 1 minute. No dielectric breakdown shall occur. | |
| Insulation Resistance | Apply 500V DC between any contactless terminal and the other terminal, with an insulation gauge and last for 1 minute 5 seconds. | 10000 M Min. | |
| Contact Resistance | Take a pair of matched terminals and measure the tail end of each terminal (voltage maximum 20mV, current maximum 100mA). | 30 m MAX. | |
| 5. Mechanical Performance / | Insertion and withdrawal forces | Rate of insertion/withdrawal: 2 mm/s. Mating of complete connectors without the effect of any latching or retaining device. | Insertion: 35 N max. Withdrawal: 2 N min. |
| Terminal Strength | Every terminal should be capable of withstand a force of 0.5 kgf for 10 seconds. | No looseness, damage, etc., but the terminal deformation is acceptable. | |
| 6. Durability / | Life test | Under the condition of no load, rotate and then plug in, rotate and then pull out with a matching plug for 1000 times in total, at a frequency of 5 times per minute. | No obvious change in appearance, destruction. Contact resistance: less than 50 m. |
| 7. Solderability / | Resistance to soldering heat | The jack terminal should be dipped in solder. Temperature of solder: 2603. Dip time: 51 seconds. After the test, the plastic base should not be deformed and the terminals should not fall off the plastic base. | |
| Solderability | Temperature of solder: 2453C. Time of dip: 30.5 seconds. Coating of solder area should be more than 95%. | ||
| 8. Environment test / | Cold test | Place the housing for 96 hours at a low temperature of -30 3 C. Then, place it under standard atmospheric conditions for 1 hour and test. | No obvious change in appearance. Contact resistance: 50 m max. Insulation resistance: 500 M min. Withstand voltage: AC 1000V. |
| Heat test | The housing should be stored at a temperature of 802 for 96 hours. Then it should be subjected to standard atmospheric conditions for 1 hour and test. | ||
| Humidity test | The housing should be stored at a temperature of 403 with relative humidity of 90% ~ 95% for 96 h. Then it should be subjected to standard atmospheric conditions for 1 hour and test. | No obvious change in appearance. Contact resistance: 50m max. Insulation resistance: 500 M min. Withstand voltage: AC 1000V. | |
| Temperature Cycling | Place the Jack under the conditions shown below and then place it in the stand at room temperature for 30 minutes. | ||
| Salt spray test | Temperature: 35 2. Solution: 5 1%. Spray time: 24 hours. Wash and dry it at room temperature after the experiment. | No obvious rust in the appearance. | |
| 9. Test condition / | Standard Test Conditions | Temperature: 15C to 35C, Relative humidity: 25% to 85%, Atmospheric pressure: 86 kPa to 106 kPa. For verification: 201C, 63% to 67% RH, 86 kPa to 106 kPa. |
2411220115_JINJIA-XLR-18P-3-N3B_C558735.pdf
Related Products
electronic connector JINJIA XLR-19-6P designed to meet strict environmental and durability standards
Through Hole Circular Connector Assemblies RoHS
Durable XLR jack combo JINJIA XLR-19P-10P designed for stable audio connections in electronic devices
Through Hole Circular Connector Assemblies RoHS
electrical JINJIA XLR-26A-10P XLR jack combo connector rated voltage 50V AC 3A and 7.5A for electronic
Through Hole Circular Connector Assemblies RoHS
Speaker socket connection XLR jack combo JINJIA XLR-11W-N3B ideal for electronic device applications
Through Hole Circular Connector Assemblies RoHS
Durable JINJIA XLR-19P-7P XLR jack connector designed for stable electrical and mechanical performance
Through Hole Circular Connector Assemblies RoHS
XLR jack connector JINJIA XLR-14-N3B designed for stable performance in electronic product applications
Through Hole Circular Connector Assemblies RoHS
XLR jack combo connector JINJIA XLR-26A-7P-N3B rated for 3A and 7.5A current electronic applications
Through Hole Circular Connector Assemblies RoHS
Electronic XLR Jack Connector JINJIA XLR-15-N3GR Rated Voltage 50V AC And Current 6A For Industrial
Through Hole Circular Connector Assemblies RoHS
Electronic connector JINJIA XLR-26AP-10P optimized for dependable audio signal performance in devices
Through Hole Circular Connector Assemblies RoHS
electrical connector JINJIA XLR-25-N3B rated 50V AC 6A operating temperature range minus 30 to plus 80 degrees
Through Hole Circular Connector Assemblies RoHS
Send RFQ
Stock:
MOQ:
