Electronic product connector JINJIA XLR-25-1 XLR jack rated voltage 50 volts AC and current 6 amperes
Manufacturer:
JINJIA
Description:
Through Hole Circular Connector Assemblies RoHS
Category:
Circular Connector Assemblies/Circular Connector Assemblies
Specifications
Mfr. Part #:
XLR-25-1
Package:
Through Hole
Model Number:
XLR-25-1
Introduction
XLR JACK SPECIFICATION
This specification applies to XLR jacks used in electronic products.
Product Attributes
- Brand: Shenzhen jinjiarun Electronic Technology Co., Ltd
- Origin: China
- Document Number: JJR-WI-47
- Issue Date: 2008-09-10
- Version: A1
Technical Specifications
| Item | Property | Test Condition | Performance |
| Rated / | Practical temperature range | -30 to +80 | - |
| Humidity range | 85% RH.MAX. | - | |
| Preservation temperature range | -10 to +40 | - | |
| Humidity range (Preservation) | 85% RH.MAX. | - | |
| Storage Environment | Around air without acid, alkaline or other corrosive gases. Storage period not exceed 180 days. | - | |
| Rated voltage and current (MAX.) | - | 50V AC , 6A | |
| Appearance | - | No scratches, soil, rust or discoloration on the surface. | |
| Construction / | Outline And Dimension | Attachment drawing | Should match the attachment drawing. |
| Part And Material | Material list specifications | Should be consistent with the material list specifications. | |
| Electrical efficiency / | Withstand Voltage | Withstand AC 1500V (50/60Hz RMS) between two non-contact terminals for 1 minute. | No dielectric breakdown shall occur. |
| Insulation Resistance | Apply 500V DC between any contactless terminal and the other terminal, with an insulation gauge and last for 1 minute 5 seconds. | 10000 M Min. | |
| Contact Resistance | Take a pair of matched terminals and measure the tail end of each terminal (voltage maximum 20mV, current maximum 100mA). | 30 m MAX. | |
| Mechanical Performance | Insertion and withdrawal forces | Rate of insertion/withdrawal: 2 mm/s. Mating of complete connectors without the effect of any latching or retaining device. | Insertion: 35 N max. Withdrawal: 2 N min. |
| Terminal Strength | Each terminal should be capable of withstand a force of 0.5 kgf for 10 seconds. | No looseness, damage, etc., but terminal deformation is acceptable. | |
| Durability / | Life test | Under no load, rotate and then plug in, rotate and then pull out with a matching plug for 1000 times in total, at a frequency of 5 times per minute. | Appearance: No obvious change or destruction. Contact resistance: less than 50 m. |
| Solderability / | Resistance to soldering heat | Dipped in solder: Temperature of solder: 2603. Dip time: 51 seconds. | After test, the plastic base should not be deformed and the terminals should not fall off the plastic base. |
| Solderability | Temperature of solder: 2453C. Time of dip: 30.5 seconds. | Coating of solder area should be more than 95%. | |
| Environment test / | Cold test | Place housing for 96 hours at -30 3 C. Then, place under standard atmospheric conditions for 1 hour and test. | Appearance: No obvious change. Contact resistance: 50 m max. Insulation resistance: 500 M min. Withstand voltage: AC 1000V. |
| Heat test | Store housing at 802 for 96 hours. Then subject to standard atmospheric conditions for 1 hour and test. | - | |
| Humidity test | Store housing at 403 with relative humidity of 90% ~ 95% for 96 h. Then subject to standard atmospheric conditions for 1 hour and test. | Appearance: No obvious change. Contact resistance: 50m max. Insulation resistance: 500 M min. Withstand voltage: AC 1000V. | |
| Temperature Cycling | Conditions as shown in original document (not detailed here). Then place in stand at room temperature for 30 minutes. | - | |
| Salt spray test | Temperature: 35 2. Solution: 5 1%. Spray time: 24 hours. Wash and dry at room temperature after experiment. | Appearance: No obvious rust. | |
| Test condition / | Standard conditions | Test and measurement temperature: 15C to 35C, relative humidity: 25% to 85%, atmospheric pressure: 86 kPa to 106 kPa. | - |
| Doubtful conditions | Test and measurement at 201 C, relative humidity 63% to 67%, and air pressure 86 kPa to 106 kPa. | - | |
| Amendment / | Specification Amendment | Negotiated and agreed by manufacturer and customer. | - |
2411220117_JINJIA-XLR-25-1_C558607.pdf
Related Products
electronic connector JINJIA XLR-19-6P designed to meet strict environmental and durability standards
Through Hole Circular Connector Assemblies RoHS
Durable XLR jack combo JINJIA XLR-19P-10P designed for stable audio connections in electronic devices
Through Hole Circular Connector Assemblies RoHS
electrical JINJIA XLR-26A-10P XLR jack combo connector rated voltage 50V AC 3A and 7.5A for electronic
Through Hole Circular Connector Assemblies RoHS
Speaker socket connection XLR jack combo JINJIA XLR-11W-N3B ideal for electronic device applications
Through Hole Circular Connector Assemblies RoHS
Durable JINJIA XLR-19P-7P XLR jack connector designed for stable electrical and mechanical performance
Through Hole Circular Connector Assemblies RoHS
XLR jack connector JINJIA XLR-14-N3B designed for stable performance in electronic product applications
Through Hole Circular Connector Assemblies RoHS
XLR jack combo connector JINJIA XLR-26A-7P-N3B rated for 3A and 7.5A current electronic applications
Through Hole Circular Connector Assemblies RoHS
Electronic XLR Jack Connector JINJIA XLR-15-N3GR Rated Voltage 50V AC And Current 6A For Industrial
Through Hole Circular Connector Assemblies RoHS
Electronic connector JINJIA XLR-26AP-10P optimized for dependable audio signal performance in devices
Through Hole Circular Connector Assemblies RoHS
electrical connector JINJIA XLR-25-N3B rated 50V AC 6A operating temperature range minus 30 to plus 80 degrees
Through Hole Circular Connector Assemblies RoHS
Send RFQ
Stock:
MOQ:
