electronic speaker socket connector JINJIA XLR-11-N3B with rated voltage 50V AC and current up to 7.5A
Manufacturer:
JINJIA
Description:
Through Hole Circular Connector Assemblies RoHS
Category:
Circular Connector Assemblies/Circular Connector Assemblies
Specifications
Mfr. Part #:
XLR-11-N3B
Package:
Through Hole
Model Number:
XLR-11-N3B
Introduction
XLR JACK (Combo) SPECIFICATION
This specification applies to XLR jack (Combo) which is used in electronic products. It is designed for speaker socket connectors in electronic devices.
Product Attributes
- Brand: Shenzhen Jinjiarun Electronic Technology Co., Ltd
- Origin: Shenzhen
- Document Number: JJR-WI-46
- Issue Date: 2008-09-10
- Version: A1
Technical Specifications
| Item | Property | Test Condition | Performance |
| 2. Rated / | |||
| 2-1. Practical temperature range | Applicable temperature range | -30 to +80 | |
| Humidity range | 85% RH.MAX. | ||
| 2-2. Preservation temperature range | Storage temperature range | -10 to +40 | |
| Humidity range | 85% RH.MAX. | ||
| Storage environment | Surrounding air without acid, alkaline or other corrosive gases. Storage period not exceeding 180 days. | ||
| 2-3. Rated voltage and current(MAX.) | Maximum rated voltage and current | 50V AC, 3A(Type A) / 7.5A(Type B) | |
| 2-4. Appearance | Surface condition | No scratches, soil, rust or discoloration. | |
| 4. Electrical efficiency / | |||
| 4-1 Withstand Voltage | Withstand AC voltage | Between two non-contact terminals for 1 minute | 1500V (50/60Hz RMS). No dielectric breakdown shall occur. |
| 4-2 Insulation Resistance | Insulation resistance | Apply 500V DC between any contactless terminal and the other terminal for 1 minute 5 seconds. | 10000 M Min. |
| 4-3 Contact Resistance | Contact resistance | Measure at the tail end of each terminal (voltage max. 20mV, current max. 100mA) for a pair of matched terminals. | 30 m MAX. |
| 5. Mechanical Performance / | |||
| 5-1 Insertion and withdrawal forces | Insertion/withdrawal speed | 2 mm/s | |
| XLR | Mating of complete connectors without the effect of any latching or retaining device | Insertion: 35 N max. Withdrawal: 2 N min. | |
| JACK | Mating of complete connectors without the effect of any latching or retaining device | Insertion: 40 N max. Withdrawal: 5 N min. | |
| 5-2 Terminal Strength | Strength test | Each terminal should withstand a force of 0.5 kgf for 10 seconds. | No looseness or damage. Terminal deformation is acceptable. |
| 6. Durability / | |||
| 6 Life test | Life cycle | Under no load, rotate and then plug in, rotate and then pull out with a matching plug for 1000 times at a frequency of 5 times per minute. | No obvious change in appearance or destruction. Contact resistance: less than 50 m. |
| 7. Solderability / | |||
| 7-1 Resistance to soldering heat | Soldering condition | Dip terminal in solder at 2603 for 51 seconds. | Plastic base should not be deformed, and terminals should not fall off. |
| 7-2 Solderability | Soldering condition | Dip in solder at 2453C for 30.5 seconds. | Solder coating area should be more than 95%. |
| 8. Environment test / | |||
| 8-1 Cold test | Condition | Place housing at -30 3 C for 96 hours, then under standard atmospheric conditions for 1 hour. | Appearance: No obvious change. Contact resistance: 50 m max. Insulation resistance: 500 M min. Withstand voltage: AC 1000V. |
| 8-2 Heat test | Condition | Store housing at 802 for 96 hours, then under standard atmospheric conditions for 1 hour. | |
| 8-3 Humidity test | Condition | Store housing at 403 with 90% ~ 95% RH for 96 hours, then under standard atmospheric conditions for 1 hour. | Appearance: No obvious change. Contact resistance: 50 m max. Insulation resistance: 500 M min. Withstand voltage: AC 1000V. |
| 8-4 Temperature Cycling | Condition | Place Jack under specified conditions, then in room temperature for 30 minutes. | |
| 8-5 Salt spray test | Condition | Temperature: 35 2. Solution: 5 1% salt. Spray time: 24 hours. Wash and dry at room temperature after experiment. | Appearance: No obvious rust. |
| 9. Test condition / | |||
| General conditions | Temperature, Humidity, Atmospheric Pressure | 15C to 35C, 25% to 85% RH, 86 kPa to 106 kPa. | For doubtful judgments: 201C, 63% to 67% RH, 86 kPa to 106 kPa. |
| 10. Amendment / | |||
| Procedure | Specification changes | Negotiated and agreed by manufacturer and customer. | |
| 12. XLR JACK (Combo) TYPE /XLR | |||
| Type | Description | Type A, Type B | |
2411220040_JINJIA-XLR-11-N3B_C558585.pdf
Related Products
electronic connector JINJIA XLR-19-6P designed to meet strict environmental and durability standards
Through Hole Circular Connector Assemblies RoHS
Durable XLR jack combo JINJIA XLR-19P-10P designed for stable audio connections in electronic devices
Through Hole Circular Connector Assemblies RoHS
electrical JINJIA XLR-26A-10P XLR jack combo connector rated voltage 50V AC 3A and 7.5A for electronic
Through Hole Circular Connector Assemblies RoHS
Speaker socket connection XLR jack combo JINJIA XLR-11W-N3B ideal for electronic device applications
Through Hole Circular Connector Assemblies RoHS
Durable JINJIA XLR-19P-7P XLR jack connector designed for stable electrical and mechanical performance
Through Hole Circular Connector Assemblies RoHS
XLR jack connector JINJIA XLR-14-N3B designed for stable performance in electronic product applications
Through Hole Circular Connector Assemblies RoHS
XLR jack combo connector JINJIA XLR-26A-7P-N3B rated for 3A and 7.5A current electronic applications
Through Hole Circular Connector Assemblies RoHS
Electronic XLR Jack Connector JINJIA XLR-15-N3GR Rated Voltage 50V AC And Current 6A For Industrial
Through Hole Circular Connector Assemblies RoHS
Electronic connector JINJIA XLR-26AP-10P optimized for dependable audio signal performance in devices
Through Hole Circular Connector Assemblies RoHS
electrical connector JINJIA XLR-25-N3B rated 50V AC 6A operating temperature range minus 30 to plus 80 degrees
Through Hole Circular Connector Assemblies RoHS
Send RFQ
Stock:
MOQ:
