XLR jack connector JINJIA XLR-04-2 featuring rated electrical characteristics and resistance to corrosion
Manufacturer:
JINJIA
Description:
Through Hole Circular Connector Assemblies RoHS
Category:
Circular Connector Assemblies/Circular Connector Assemblies
Specifications
Mfr. Part #:
XLR-04-2
Package:
Through Hole
Model Number:
XLR-04-2
Introduction
XLR Jack Specification
This specification applies to XLR jacks used in electronic products. It details the product's rated values, construction, electrical characteristics, mechanical performance, durability, solderability, environmental resistance, and testing conditions.
Product Attributes
- Brand: Shenzhen jinjiarun Electronic Technology Co., Ltd
- Origin: China
- Model Type: XLR JACK
Technical Specifications
| Item | Property | Test Condition | Performance |
| 2. Rated / | |||
| Practical temperature range | -30to +80 | ||
| Humidity range | 85% RH.MAX. | ||
| Preservation temperature range | -10to +40 | ||
| Humidity range (Preservation) | 85% RH.MAX. | ||
| Storage Condition | Ambient air without acid, alkaline, or corrosive gases. Storage period not exceeding 180 days. | ||
| Rated voltage and current (MAX.) | 50V AC , 6A | ||
| Appearance | No scratches, soil, rust, or discoloration on the surface. | ||
| 3. Construction / | |||
| Outline And Dimension | Should match the attachment drawing. | ||
| Part And Material | Should be consistent with the material list specifications. | ||
| 4. Electrical efficiency / | |||
| Withstand Voltage | Withstand AC 1500V (50/60Hz RMS) between two non-contact terminals for 1 minute. No dielectric breakdown shall occur. | Between two non-contact terminals | No dielectric breakdown |
| Insulation Resistance | Apply 500V DC between any contactless terminal and the other terminal, with an insulation gauge and last for 1 minute 5 seconds. | Between contactless terminals | 10000 M Min. |
| Contact Resistance | Take a pair of matched terminals and measure the tail end of each terminal (voltage maximum 20mV, current maximum 100mA). | Matched terminals, tail end measurement | 30 m MAX. |
| 5. Mechanical Performance / | |||
| Insertion and withdrawal forces | Rate of insertion/withdrawal: 2 mm/s. Mating of complete connectors without the effect of any latching or retaining device. | Insertion: 35 N max. Withdrawal: 2 N min. | |
| Terminal Strength | Every terminal should be capable of withstand a force of 0.5 kgf for 10 seconds. There is no looseness, damage, etc., but terminal deformation is acceptable. | No looseness, damage. Deformation acceptable. | |
| 6. Durability / | |||
| Life test | Under no load conditions, rotate and then plug in, rotate and then pull out with a matching plug for 1000 times in total, at a frequency of 5 times per minute. | Matching plug, 1000 cycles | Appearance: No obvious change. Contact resistance: < 50 m. |
| 7. Solderability / | |||
| Resistance to soldering heat | The jack terminal should be dipped in solder: Temperature 2603, Dip time 51 seconds. After the test, the plastic base should not be deformed and the terminals should not fall off the plastic base. | Solder dip | Plastic base: No deformation. Terminals: No detachment. |
| Solderability | Temperature of solder: 2453C. Time of dip: 30.5 seconds. Coating of solder area should be more than 95%. | Solder dip | Solder area coverage: > 95%. |
| 8. Environment test / | |||
| Cold test | Place the housing for 96 hours at -30 3 C. Then, place under standard atmospheric conditions for 1 hour and test. | -30 3 C for 96h, then 1h standard conditions | Appearance: No obvious change. Contact resistance: 50 m. Insulation resistance: 500 M. Withstand voltage: AC 1000V. |
| Heat test | The housing should be stored at 802 for 96 hours. Then, subject to standard atmospheric conditions for 1 hour and test. | 802 for 96h, then 1h standard conditions | |
| Humidity test | Store at 403 with 90% ~ 95% RH for 96 h. Then, subject to standard atmospheric conditions for 1 hour and test. | 403, 90%~95% RH for 96h, then 1h standard conditions | Appearance: No obvious change. Contact resistance: 50 m. Insulation resistance: 500 M. Withstand voltage: AC 1000V. |
| Temperature Cycling | Place the Jack under specified conditions and then place in stand at room temperature for 30 minutes. | Specified conditions | |
| Salt spray test | Temperature: 35 2. Solution: 5 1%. Spray time: 24 hours. Wash and dry at room temperature after the experiment. | 35 2, 5 1% salt solution, 24h | Appearance: No obvious rust. |
| 9. Test condition / | |||
| Standard conditions | Test and measurement temperature: 15C to 35C, relative humidity: 25% to 85%, atmospheric pressure: 86 kPa to 106 kPa. | ||
| Doubtful conditions | Test and measurement at 201C, relative humidity 63% to 67%, and air pressure 86 kPa to 106 kPa. | ||
| 10. Amendment / | |||
| Procedure | Amendments require negotiation and agreement between the manufacturer and the customer. | ||
2411220125_JINJIA-XLR-04-2_C558737.pdf
Related Products
electronic connector JINJIA XLR-19-6P designed to meet strict environmental and durability standards
Through Hole Circular Connector Assemblies RoHS
Durable XLR jack combo JINJIA XLR-19P-10P designed for stable audio connections in electronic devices
Through Hole Circular Connector Assemblies RoHS
electrical JINJIA XLR-26A-10P XLR jack combo connector rated voltage 50V AC 3A and 7.5A for electronic
Through Hole Circular Connector Assemblies RoHS
Speaker socket connection XLR jack combo JINJIA XLR-11W-N3B ideal for electronic device applications
Through Hole Circular Connector Assemblies RoHS
Durable JINJIA XLR-19P-7P XLR jack connector designed for stable electrical and mechanical performance
Through Hole Circular Connector Assemblies RoHS
XLR jack connector JINJIA XLR-14-N3B designed for stable performance in electronic product applications
Through Hole Circular Connector Assemblies RoHS
XLR jack combo connector JINJIA XLR-26A-7P-N3B rated for 3A and 7.5A current electronic applications
Through Hole Circular Connector Assemblies RoHS
Electronic XLR Jack Connector JINJIA XLR-15-N3GR Rated Voltage 50V AC And Current 6A For Industrial
Through Hole Circular Connector Assemblies RoHS
Electronic connector JINJIA XLR-26AP-10P optimized for dependable audio signal performance in devices
Through Hole Circular Connector Assemblies RoHS
electrical connector JINJIA XLR-25-N3B rated 50V AC 6A operating temperature range minus 30 to plus 80 degrees
Through Hole Circular Connector Assemblies RoHS
Send RFQ
Stock:
MOQ:
