electronic connector JINJIA XLR-18P-N3B with insulation resistance 10000 M ohm and withstand voltage 1500V AC
Manufacturer:
JINJIA
Description:
Through Hole Circular Connector Assemblies RoHS
Category:
Circular Connector Assemblies/Circular Connector Assemblies
Specifications
Mfr. Part #:
XLR-18P-N3B
Package:
Through Hole
Model Number:
XLR-18P-N3B
Introduction
Product Overview
This specification applies to XLR jack connectors used in electronic products. It details the electrical, mechanical, durability, and environmental performance characteristics of the XLR jack.
Product Attributes
- Brand: (Shenzhen jinjiarun Electronic Technology Co., Ltd)
- Origin: China
- Document Number: JJR-WI-47
- Issue Date: 2008-09-10
- Version: A1
Technical Specifications
| Item | Property | Test Condition | Performance |
| 2. Rated / | Practical temperature range | -30 to +80 | |
| Humidity range | 85% RH.MAX. | ||
| Rated voltage and current (MAX.) | 50V AC, 6A | ||
| 4. Electrical efficiency / | Withstand Voltage () | Withstand AC 1500V (50/60Hz RMS) between two non-contact terminals for 1 minute. No dielectric breakdown shall occur. | No dielectric breakd own shall occur. |
| Insulation Resistance () | Apply 500V DC between any contactless terminal and the other terminal, with an insulation gauge and last for 1 minute 5 seconds. | 10000 M Min. | |
| 4-3 Contact Resistance | Take a pair of matched terminals and measure the tail end of each terminal (voltage maximum 20mV, current maximum 100mA) | 30 m MAX. | |
| 5. Mechanical Performance | Insertion and withdrawal forces () | Rate of insertion/withdrawal: 2 mm/s. Mating of complete connectors without the effect of any latching or retaining device. | Insertion: 35 N max. Withdrawal: 2 N min. |
| Terminal Strength () | Every terminal should be capable of withstand a force of 0.5 kgf for 10 seconds. | There is no looseness, damage, etc., but the terminal deformation is acceptable. | |
| 6. Durability / | Life test () | Under the condition of no load, rotate and then plug in, rotate and then pull out with a matching plug for 1000 times in total, at a frequency of 5 times per minute. | Appearance: No obvious change, destruction. Contact resistance: less than 50 m. |
| 7. Solderability / | Resistance to soldering heat () | The jack terminal should be dipped in solder. Temperature of solder: 2603. Dip time: 51 seconds. | After the test, the plastic base should not be deformed and the terminals should not fall off the plastic base. |
| Solderability () | Temperature of solder: 2453C. Time of dip: 30.5 seconds. | Coating of solder area should be more than 95%. | |
| 8. Environment test / | Cold test () | Place the housing for 96 hours at a low temperature of -30 3 C. Then, place it under standard atmospheric conditions for 1 hour and test. | Appearance: No obvious change. Contact resistance: 50 m max. Insulation resistance: 500 M min. Withstand voltage: AC 1000V. |
| Heat test () | The housing should be stored at a temperature of 802 for 96 hours. Then it should be subjected to standard atmospheric conditions for 1 hour and test. | (Performance details not fully specified for this test in the provided text, only conditions) | |
| Humidity test () | The housing should be stored at a temperature of 403 with relative humidity of 90% ~ 95% for 96 h. Then it should be subjected to standard atmospheric conditions for 1 hour and test. | Appearance: No obvious change. Contact resistance: 50m max. Insulation resistance: 500 M min. Withstand voltage: AC 1000V. | |
| 8-5 Salt spray test () | Temperature: 35 2 Solution: 5 1% Spray time: 24 hours. Wash and dry it at room temperature after the experiment. | Appearance: No obvious rust. | |
| 9. Test condition / | Unless otherwise specified, the test and measurement temperature is between 15 C and 35 C, the relative humidity is between 25% and 85%, and the atmospheric pressure is between 86 kPa and 106 kPa. However, when any doubts arise on the judgment value under the above condition, the test and measurement are carried out at 201 C, the relative humidity is 63% to 67%, and the air pressure is performed at 86 kPa to 106 kPa. | (Standard test conditions) |
2411220546_JINJIA-XLR-18P-N3B_C558733.pdf
Related Products
electronic connector JINJIA XLR-19-6P designed to meet strict environmental and durability standards
Through Hole Circular Connector Assemblies RoHS
Durable XLR jack combo JINJIA XLR-19P-10P designed for stable audio connections in electronic devices
Through Hole Circular Connector Assemblies RoHS
electrical JINJIA XLR-26A-10P XLR jack combo connector rated voltage 50V AC 3A and 7.5A for electronic
Through Hole Circular Connector Assemblies RoHS
Speaker socket connection XLR jack combo JINJIA XLR-11W-N3B ideal for electronic device applications
Through Hole Circular Connector Assemblies RoHS
Durable JINJIA XLR-19P-7P XLR jack connector designed for stable electrical and mechanical performance
Through Hole Circular Connector Assemblies RoHS
XLR jack connector JINJIA XLR-14-N3B designed for stable performance in electronic product applications
Through Hole Circular Connector Assemblies RoHS
XLR jack combo connector JINJIA XLR-26A-7P-N3B rated for 3A and 7.5A current electronic applications
Through Hole Circular Connector Assemblies RoHS
Electronic XLR Jack Connector JINJIA XLR-15-N3GR Rated Voltage 50V AC And Current 6A For Industrial
Through Hole Circular Connector Assemblies RoHS
Electronic connector JINJIA XLR-26AP-10P optimized for dependable audio signal performance in devices
Through Hole Circular Connector Assemblies RoHS
electrical connector JINJIA XLR-25-N3B rated 50V AC 6A operating temperature range minus 30 to plus 80 degrees
Through Hole Circular Connector Assemblies RoHS
Send RFQ
Stock:
MOQ:
