Tested RF Coaxial Connector MyAntenna A-IPEX1-1.25A Meeting Strict Electrical Mechanical Requirements
Manufacturer:
MyAntenna
Description:
Connector Receptacle IPEX Male Pin 50Ω Surface Mount
Category:
Coaxial Connector (RF) Adapters/Coaxial Connector (RF) Assemblies
Specifications
Number Of Ports:
1
Interface:
内针
RF Series:
IPEX
Connector Type:
板端
Frequency:
6GHz
Impedance:
50Ω
Interface Diameter:
2mm
Mfr. Part #:
A-IPEX1-1.25A
Package:
SMD
Model Number:
A-IPEX1-1.25A
Introduction
Product Overview
This product specification defines the product performance and the test methods to ascertain the performance of the RF coaxial connector, which is designed and manufactured by TREASURE ADVANCE ENTERPRISES LIMITED. This RF coaxial connector is designed to meet electrical, mechanical, and environmental performance requirements.
Product Attributes
- Brand: TREASURE ADVANCE ENTERPRISES LIMITED
- Certifications: UL498 (Standard for safety of attachment plug and receptacle)
- Harmful Material Control: Follows ROSH directive requirements.
- Marking: Manufacturers name, industry recognized logo, or customer approved marks. Green cresset is the mark of lead free processing.
Technical Specifications
| Item | Requirements | Test Methods |
| 1. Examination of Product | Product shall be conforming to the requirements of applicable product drawing. | Visually, dimensions and functionally inspected per applicable product drawing. |
| 2. Contact Resistance (Low Level) | 20 m Max. initial | Subject mated contacts assembled in housing to closed circuit of 10 mA max. at open circuit voltage of 20 mV max. |
| 3. Insulation Resistance | 500 M Min. | Measure by applying test potential between the adjacent contacts, and between the contacts and ground in the mated connector. MIL-STD-202, Method 302, Condition B (100 V DC10%). |
| 4. Dielectric Strength | Connector must withstand test potential of 100 VAC for 1 minute.Current leakage must be 0.5 mA max.. | Measure by applying test potential between the adjacent contacts, and between the contacts and ground in the mated connector. MIL-STD-202, Method 301. |
| 5. Unmating Force | Total unmate force: Initial 5N min. after 30 cycles 3Nmin. | Unmate the receptacle at a speed 253mm/m by the push-on/pull-off machine |
| 6. Durability (Repeated Mating/Unmating) | Contact Resistance: 30m Max. after testing | Mate and unmate connector for 30 cycle. |
| 7. Crimp strength | 10N min | Pull the cable as shown at a speed 253mm/m by tensile strength machine. |
| 8. Vibration Sinusoidal Low Frequency | No electrical discontinuity greater then 1 sec (s) shall occur. Contact resistance:30 m max. | Subject mated connector to 10-55-10 Hz traversed in 1 minute at 1.5 mm amplitude 2 hours each of 3 mutually perpendicular plane, 10 mA applied MIL-STD-202, Method 201. |
| 9. Thermal shock | No damage, Contact Resistance (Low Level) (Final) 30 m max. | Temperature range from -55C to +85C .Start from -55C,after 30 min. change to +85C;change time is no more than 30 seconds. Total 5 cycles. MIL-STD-202, Method 107D,condition A. |
| 10. Humidity | No damage, Contact Resistance (Low Level) (Final) 30 m max.. Dielectric Strength should be OK, Insulation Resistance should be 200 M min. | Temperature :402C 96 hours. Relative Humidity : 90-95%; Duration :96 Hours. MIL-STD-202, Method 103. |
| 11. Salt Spray | Contact Resistance (Low Level) (Final)100 mmax. | 51% salt concentration 484 hours 352C MIL-STD-202, Method 101 Condition B. |
| 12. High temperature | Contact resistance: 100 mmax. | Subject product to 852C for 96 hours continuously. MIL-STD-202, Method 108. |
| 13. VSWR | 1.3max. at 0.1GHz~3GHz; 1.5max. at 3GHz~6GHz | Measure the VSWR as shown by the network,analyzerFrequency:100MHz~6GHz |
| Test Description | Test Sequence A | Test Sequence B | Test Sequence C | Test Sequence D | Test Sequence E | Test Sequence F | Test Sequence G | Test Sequence H | Test Sequence I | Test Sequence J | Test Sequence K |
| 1. Examination of Product | 1,3 | 1,3 | 1,5 | 1,5 | 1,5 | 1,5 | 1,9 | 1,9 | 1.4 | 1.7 | 1.3 |
| 2. Contact Resistance (Low Level) | 2 | 2,4 | 2,4 | 2,4 | 2.4 | 2.8 | 2.8 | 2.5 | 2.5 | ||
| 3. Insulation Resistance | 3,6 | 3,6 | 3,6 | ||||||||
| 4. Dielectric Strength | 4,7 | 4,7 | |||||||||
| 5. Unmating Force | 2 | ||||||||||
| 6. Durability | 3 | ||||||||||
| 7. Crimp strength | 3 | 2 | |||||||||
| 8. Vibration Sinusoidal Low Frequency | 3 | ||||||||||
| 9. Thermal shock | 3 | 5 | |||||||||
| 10. Humidity | 5 | ||||||||||
| 11. Salt Spray | 3 | ||||||||||
| 12. High temperature | 4 | ||||||||||
| 13. VSWR |
2410121459_MyAntenna-A-IPEX1-1-25A_C22467595.pdf
Related Products
PCB Mount SMA Jack Connector MyAntenna A-SMA-KE-13.5A Featuring Gold Plated Brass and PTFE Insulator
1 Inner Bore SMA Board Side Offset Pin 6GHz 50Ω 5.35mm SMD Coaxial Connector (RF) Assemblies RoHS
PCB Mount SMA Connector MyAntenna A-SMA-KWE-16.18A Supporting DC to 6GHz Frequency Range and 50 Ohm Impedance
Connector Receptacle SMA Female Pin 50Ω Through Hole Positive Pin
PCB Mount SMA Jack Connector with 500 Plug Unplug Cycles and RoHS Compliance MyAntenna A-SMA-KE-16.5A Electrical Specs
Connector Receptacle SMA Female Pin 50Ω Surface Mount Offset Pin
RF coaxial connector MyAntenna A-IPEX3-0.85A featuring low contact resistance and ROSH certification
Connector Receptacle IPEX Male Pin 50Ω Surface Mount
MyAntenna A IPEX4 0 6A SMT RF Connector for PDA Mobile Phones Wireless LAN Bluetooth and GPS Devices
Connector Receptacle IPEX Male Pin 50Ω Surface Mount,1.8x1.7mm
Durable RF 1.0H Connector MyAntenna A-IPEX5-0.57A with Brass Bronze Contacts and Phosphor Bronze Shell
Connector Receptacle IPEX Male Pin 50Ω Surface Mount,1.7x1.7mm
Send RFQ
Stock:
MOQ:
