USB component hanxia HX 10.0 HCHTZB6.3 tested for connection force and performance in pressure range 86 to 106 Kpa
Manufacturer:
hanxia
Description:
SMD USB, DVI, HDMI Connector Assemblies RoHS
Category:
USB, DVI, HDMI Connector Adapters/USB, DVI, HDMI Connector Assemblies
Specifications
Mfr. Part #:
HX 10.0 HCHTZB6.3
Package:
SMD
Model Number:
HX 10.0 HCHTZB6.3
Introduction
Product Overview
This document outlines the specifications for the HX 10.0 HCHTZB6.3 product from Shenzhen Hanxia Electronic Co., Ltd. It details the product's electrical, mechanical, and durability characteristics, intended for use within a specific temperature range and under standard atmospheric conditions. This specification sheet serves as an approval document for customers.
Product Attributes
- Brand: (Hanxia)
- Origin: (Shenzhen Hanxia Electronic Co., Ltd)
- Part No: HX 10.0 HCHTZB6.3
- Project: USB
Technical Specifications
| Item | Test Conditions | Performance | |||
| RATING | |||||
| DC 30V 1.5A | |||||
| PRACTICAL TEMPERATURE RANGE | |||||
| -25~85C | -25C~+85C | ||||
| STANDARD ATMOSPHERIC CONDITIONS | |||||
| (1) BETWEEN BODY AND CONDUCTOR: 5C TO 35 (2) BETWEEN CONDUCTORS NOT TO BE CONTACT45% TO 85% (3) PRESSURE86Kpa TO 106Kpa | (1) 5~35 (2) 45%~85% (3) 86 Kpa~106Kpa | ||||
| MECHANICAL | |||||
| 1 | CONNECTION FORCE | MEASUREMENT SHALL BE MADE AFTER CONNECTING AND DISCONNECTING USING STANDARD PLUG GAUGE 3 TIMES | PLUG GAUGE 3 | 3.57Kgf MAX | |
| 2 | DISCONNECTI ON FORCE | MEASUREMENT SHALL BE MADE AFTER CONNECTING AND DISCONNECTING USING STANDARD PLUG GAUGE 3 TIMES | PLUG GAUGE 3 | 1.02Kgf MIN | |
| 3 | TERMINAL STRENGTH | A STATIC LOAD OF 0.1N/m(1kgf/cm)SHALL BE APPLIED TO THE TIP OF THE TERMINAL FOR 1 MIN IN ANY DIRECTION | 1 0.1N/m(1kgf/cm). | THERE SHALL BE NO DAMAGE TO THE TERMINAL SUCH AS CRACKS, LOOSENESS OR PLAY ELECTRICAL ,AND MECHANICAL CHARACTERISTICS SHALL BE SATISFIED | |
| ELECTRICAL | |||||
| 3.1 | CONTACT RESISTANCE | MEASURED AT SMALL CURRENT 100m A OR LESS 1000Hz | 100 m A | 30m MAX | |
| 3.2 | INSULATION RESISTANCE | APPLY A VOLTAGE OF 100V DC FOR 1 MIN TO FOLLOWING PORTIONS AFTER WHICH MEASUREMENT SHALL BE MADE: (1) BETWEEN BODY AND CONDUCTOR (2) BETWEEN CONDUCTORS NOT TO BE CONTACT (3) BETWEEN CONDUCTORS NOT TO BE WHEN PLUG IS INSERTED | 100V DC 1 1 2 3 | 1000M MIN | |
| 3.3 | DIELECTRIC STRENGTH | AC 500V ims(50~60Hz)FOR 1 MIN TRIP CURRENT:0.5mA (1) BETWEEN BODYAND CONDUCTOR (2) BETWEEN CONDUCTORS NOT TO BE CONTACL (3) BETWEEN CONDUCTORS NOT TO BE WHEN PLUG IS INSERTED | AC 500V 50Hz/min 1 0.5mA, : (1) (2) (3) | WITHOUT DAMAGE TO PARTS ARCING OR BREAKDOWN ETC | |
| DURABILITY | |||||
| 4.1 | SOLDERABILITY TEST | THE TOP OF THE TERMINALS SHALL BE DIPPED 1mm IN THE SOLDER BATH OF 2505 FOR 50.5 SECONDS | 1mm ,2505,5 0.5 | 1SOLDER WETTING TIME SHALL BE 3 SEC OR LESS 2THE AREA OF SOLDERING SHOULD BE OVER 75% | 1 3 2 75% |
| 4.2 | RESISTANCE TO SOLDERING HEAT TEST | REFLOW SOLDERING CONDITIONS: PREHEAT:TEMPERATURE ON THE COPPER FOIL SURFACE SHOULD REACH 180 .120 S AFTER THE P.C.B ENTERED INTO THE SOLDERING EQUIPMENT. TALLEST TEMPERATURE:TEMPERATURE ON THE COPPER FOIL SURFACE SHOULD REACH THE PEAK TEMPERATURE OF 2605 WITH IN 20 SECONDS. | :180,120s :260520 | WITHOUT DEFOR MATION OF CASE OR EXCESSIVE LOOSENESS OF TEMINALS ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED | |
| SOLDERING IRON METHOD: BIT TEMPERATURE 3305 APPLICATION TIME OF SOLDERING IRON30.5 SEC HOWEVER EXCESSIVE PRESSURE SHALL NOT BE APPLIED TO THE TERMINAL | 3305 30.5 | WITHOUT DEFORMATION OF CASE OR EXCESSIVE LOOSENESS OF TEMINALS ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED | |||
| 4.3 | HUMIDITY TEST | THE JACK SHALL BE STORED AT A TEMPERATURE OF 402 AND A HUMIDITY OF 90%TO 96% FOR 96 Hr,THEN THE JACK SHALL BE MAINTAINED AT STANDARD ATMOSPHERIC CONDITION FOR 1 Hr FOR OTHER PROCEDURES | 40290~96% Hr 96 1 | ||
| 4.4 | HEAT TEST | THE JACK SHALL BE STORED AT A TEMPERATURE OF702 FOR 96 HOURSAND THEN IT SHALL BE SUBJECTED TO THE CONTROLLED RECOVERY MBASURBM | 70296 1 | THERE SHALL BE NO DAMAGE ON APPEARANCE MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED | |
| 4.5 | COLD TEST | THE JACK SHALL BE STORED AT A TEMPERATURE OF-253 FOR 96 HOURS AND THEN IT SHALL BE SUBJECTED TO THE CONTROLLED RECOVERY CONDITIONS FOR 1 HOUR AFTER WHICH | -25396 1 | THERE SHALL BE NO DAMAGE ON APPEARANCE MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED | |
| 4.6 | LIFE TEST | CONNECTION AND DISCONNECTION SHALL BE MADE 5000 CYCLES AT A SPEED 10 TO 20 CYCLES / MIN LOAD: AT RATING CONDITION NON-INDUCTIVE LOAD | ()1 10-20 5000 | (1) CONTACT RESISTANCE SHALL BE 0.1 (2) DISCONNECTION FORCE SHALL BE 0.8 TO 2.0N (3) MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED | (1) 0.1 (2) 0.8~2.0N (3) :, |
| WITHOUT LOAD CONNECTION AND DISCONNECTION SHALL BE MADE WITH THE MATING PLUGS AND JACKS FOR 5000 CYCLES AT A SPEED OF 10 TO 25 CYCLES/MIN | Plug()1 10-255000 | ||||
| 4.7 | TEMPARATURE CYCLINGTEST | THE JACK SHALL BE SUB JECTED TO 5 CYCLES OF THE FOLLOWING CONDITIONS SHOWED IN THE FIGURE,AND THEN SHALL RETURNED ALLOWED TO REMAIN IN ROOM AMBIENT CONDITION FOR 30 MINUTES | 5 30 | THERE SHALL BE NO DEFORMATION OR CRACKS IN MOLDED PART. INSERTION EXTRACTION FORCE:3 TO 20N CONTACT RESISTANCE:MAX.30M INSULATION RESISTANCE: MIN.100 M DIELECTRIC WITHSTANDING VOLTAGE: 100VAC/MIN(BETWEEN TERMINALS) | 3N 20N 30m 100 M 100VAC |
| 4.8 | COLD&HEAT SHOCK TEST | THE JACK SHALL BE SUBJECTED TO5 CYCLES OF THE FOLLOWING CONDITIONS SHOWED IN THE FIGURE,AND THEN SHALL RETURNED AND ALLOWED TO REMAIN IN ROOM AMBIENT CONDITION FOR 30 MINUTES | 5 30 | THERE SHALL BE NO DEFORMATION OR CRACKS IN MOLDED PART. INSERTION EXTRACTION FORCE:3 TO 25N CONTACT RESISTANCE:MAX.30M INSULATION RESISTANCE: MIN.100 M DIELECTRIC WITHSTANDING VOLTAGE: 500VAC/MIN(BETWEEN TERMINALS) | 3N 25N 30m 100 M 500VAC |
2410121438_hanxia-HX-10-0-HCHTZB6-3_C7430291.pdf
Related Products
Electronic Connector hanxia HX MICRO 180D ZB Featuring Nickel Base and Gold Plated Contact Terminal
USB-Micro B Receptacle Connector Through Hole
Durable hanxia HX 10.0 180 ZCZB USB connector rated DC 30V 1.5A for industrial applications
USB-A (USB TYPE-A) Receptacle Connector 4 Position Through Hole
Temperature resistant USB cable Hanxia HX 10.0 4C6.3 JB rated DC 30V 1.5A for electrical connection
USB-A (USB TYPE-A) Receptacle Connector 4 Position Right Angle
USB connector hanxia HX AF 90 ZJDG JB offering robust connection and insulation resistance properties
Through Hole USB, DVI, HDMI Connector Assemblies RoHS
HX MICRO 7.2 JBWZ Micro USB connector offering low contact resistance and high insulation resistance
USB-Micro B Receptacle Connector Surface Mount, Right Angle
Durable hanxia HX MICRO 2PCB1.6 ZB Micro USB connector with tested mechanical and electrical specifications
USB-Micro B Receptacle Connector Recessed Mount
Micro USB Connector Hanxia HX MICRO 4PCB1.0 JB with C5191 Nickel Base and Gold Plated Contact Terminal
USB-Micro B Receptacle Connector Recessed Mount
Micro USB Connector Hanxia HX MICRO DNJ JB with Durable Plastic and Gold Plated Contact Terminals
USB-Micro B Receptacle Connector Surface Mount, Right Angle
Electrical connector hanxia HX AM 90D with plated gold contacts in mating area and tin on solder tails
USB-A (USB TYPE-A) Receptacle Connector 4 Position Through Hole
Micro USB hanxia HX 10.0 4JCHT6.3 product specification with temperature humidity and pressure tolerance
USB-A (USB TYPE-A) Receptacle Connector 4 Position Surface Mount, Right Angle
Send RFQ
Stock:
MOQ:
