Temperature resistant USB cable Hanxia HX 10.0 4C6.3 JB rated DC 30V 1.5A for electrical connection
Manufacturer:
hanxia
Description:
USB-A (USB TYPE-A) Receptacle Connector 4 Position Right Angle
Category:
USB, DVI, HDMI Connector Adapters/USB, DVI, HDMI Connector Assemblies
Specifications
Number Of Ports:
1
Number Of Contacts:
4P
Mounting Type:
弯插
Current Rating:
1.5A
Operating Temperature:
-25℃~+85℃
Connector Type:
Type-A
Gender:
母
Mfr. Part #:
HX 10.0 4C6.3 JB
Package:
Through Hole
Model Number:
HX 10.0 4C6.3 JB
Introduction
Product Overview
This document outlines the specifications for the HX 10.0 4C6.3 JB USB product from Shenzhen Hanxia Electronic Co., Ltd. It details the product's technical performance, including electrical, mechanical, and durability characteristics, designed for operation within a temperature range of -25~85C.
Product Attributes
- Brand: Hanxia Electronic
- Origin: Shenzhen, China
- Model: HX 10.0 4C6.3 JB
- Part Number: HX 10.0 4C6.3 JB
- Customer Approval Signatures: Zhang Wei, Luo Xiaochun, Huang Bin
- Manufacturer: Shenzhen Hanxia Electronic Co., Ltd.
Technical Specifications
| Item | Test Conditions | Performance | |||
| RATING | PRACTICAL TEMPERATURE RANGE | DC 30V 1.5A | -25~85C | ||
| STANDARD ATMOSPHEIC CONDITIONS | UNLESS OTHERWISE SPECIFIED THE STANDARD RANGE OF ATMOSPHERIC CONDITIONS FOR MAKING MEASUREMENTS AND TESTS ARE AS FOLLOWS:(1) BETWEEN BODY AND CONDUCTOR: 5C TO 35 (2) BETWEEN CONDUCTORS NOT TO BE CONTACT45% TO 85% (3) PRESSURE86Kpa TO 106Kpa | (1) 5~35 (2) 45%~85% (3) 86 Kpa~106Kpa | |||
| MECHANICAL | CONNECTION FORCE | MEASUREMENT SHALL BE MADE AFTER CONNECTING AND DISCONNECTING USING STANDARD PLUG GAUGE 3 TIMES | 3.57Kgf MAX | ||
| DISCONNECTI ON FORCE | MEASUREMENT SHALL BE MADE AFTER CONNECTING AND DISCONNECTING USING STANDARD PLUG GAUGE 3 TIMES | 1.02Kgf MIN | |||
| TERMINAL STRENGTH | A STATIC LOAD OF 0.1N/m(1kgf/cm)SHALL BE APPLIED TO THE TIP OF THE TERMINAL FOR 1 MIN IN ANY DIRECTION | THERE SHALL BE NO DAMAGE TO THE TERMINAL SUCH AS CRACKS, LOOSENESS OR PLAY ELECTRICAL ,AND MECHANICAL CHARACTERISTICS SHALL BE SATISFIED | |||
| ELECTRICAL | CONTACT RESISTANCE | MEASURED AT SMALL CURRENT 100m A OR LESS 1000Hz | 30m MAX | ||
| INSULATION RESISTANCE | APPLY A VOLTAGE OF 100V DC FOR 1 MIN TO FOLLOWING PORTIONS AFTER WHICH MEASUREMENT SHALL BE MADE: (1) BETWEEN BODY AND CONDUCTOR (2) BETWEEN CONDUCTORS NOT TO BE CONTACT (3) BETWEEN CONDUCTORS NOT TO BE WHEN PLUG IS INSERTED | 1000M MIN | |||
| DIELECTRIC STRENGTH | IS INSERTED DC 500V 1 MIN AC 500V 50Hz/min 1 0.5mA, : (1) (2) (3) | WITHOUT DAMAGE TO PARTS ARCING OR BREAKDOWN ETC | |||
| DURABILITY | SOLDERA- BILITY TEST | THE TOP OF THE TERMINALS SHALL BE DIPPED 1mm IN THE SOLDER BATH OF 2505 FOR 50.5 SECONDS | 1SOLDER WETTING TIME SHALL BE 3 SEC OR LESS 2THE AREA OF SOLDERING SHOULD BE OVER 75% | ||
| RESISTANCE TO SOLDERING HEAT TEST | REFLOW SOLDERING CONDITIONS: PREHEAT:TEMPERATURE ON THE COPPER FOIL SURFACE SHOULD REACH 180 .120 S AFTER THE P.C.B ENTERED INTO THE SOLDERING EQUIPMENT. TALLEST TEMPERATURE:TEMPERATURE ON THE COPPER FOIL SURFACE SHOULD REACH THE PEAK TEMPERATURE OF 2605 WITH IN 20 SECONDS. | WITHOUT DEFOR MATION OF CASE OR EXCESSIVE LOOSENESS OF TEMINALS ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED | |||
| SOLDERING IRON METHOD: BIT TEMPERATURE 3305 APPLICATION TIME OF SOLDERING IRON30.5 SEC HOWEVER EXCESSIVE PRESSURE SHALL NOT BE APPLIED TO THE TERMINAL | WITHOUT DEFORMATION OF CASE OR EXCESSIVE LOOSENESS OF TEMINALS ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED | ||||
| HUMIDITY TEST | THE JACK SHALL BE STORED AT A TEMPERATURE OF 402 AND A HUMIDITY OF 90%TO 96% FOR 96 Hr,THEN THE JACK SHALL BE MAINTAINED AT STANDARD ATMOSPHERIC CONDITION FOR 1 Hr FOR OTHER PROCEDURES | ||||
| HEAT TEST | THE JACK SHALL BE STORED AT A TEMPERATURE OF702 FOR 96 HOURSAND THEN IT SHALL BE SUBJECTED TO THE CONTROLLED RECOVERY MBASURBM | THERE SHALL BE NO DAMAGE ON APPEARANCE MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED | |||
| COLD TEST | THE JACK SHALL BE STORED AT A TEMPERATURE OF-253 FOR 96 HOURS AND THEN IT SHALL BE SUBJECTED TO THE CONTROLLED RECOVERY CONDITIONS FOR 1 HOUR AFTER WHICH | THERE SHALL BE NO DAMAGE ON APPEARANCE MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED | |||
| LIFE TEST | CONNECTION AND DISCONNECTION SHALL BE MADE 5000 CYCLES AT A SPEED 10 TO 20 CYCLES / MIN LOAD AT RATING CONDITION NON-INDUCTIVE LOAD | (1) CONTACT RESISTANCE SHALL BE 0.1 (2) DISCONNECTION FORCE SHALL BE 0.8 TO 2.0N (3) MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED | |||
| TEMPARATURE CYCLINGTEST | THE JACK SHALL BE SUB JECTED TO 5 CYCLES OF THE FOLLOWING CONDITIONS SHOWED IN THE FIGURE,AND THEN SHALL RETURNED ALLOWED TO REMAIN IN ROOM AMBIENT CONDITION FOR 30 MINUTES | THERE SHALL BE NO DEFORMATION OR CRACKS IN MOLDED PART. INSERTION EXTRACTION FORCE:3 TO 20N CONTACT RESISTANCE:MAX.30M INSULATION RESISTANCE: MIN.100 M DIELECTRIC WITHSTANDING VOLTAGE: 100VAC/MIN(BETWEEN TERMINALS) | |||
| COLD&HEAT SHOCK TEST | THE JACK SHALL BE SUBJECTED TO5 CYCLES OF THE FOLLOWING CONDITIONS SHOWED IN THE FIGURE,AND THEN SHALL RETURNED AND ALLOWED TO REMAIN IN ROOM AMBIENT CONDITION FOR 30 MINUTES | THERE SHALL BE NO DEFORMATION OR CRACKS IN MOLDED PART. INSERTION EXTRACTION FORCE:3 TO 25N CONTACT RESISTANCE:MAX.30M INSULATION RESISTANCE: MIN.100 M DIELECTRIC WITHSTANDING VOLTAGE: 500VAC/MIN(BETWEEN TERMINALS) |
2410121438_hanxia-HX-10-0-4C6-3-JB_C7430287.pdf
Related Products
Electronic Connector hanxia HX MICRO 180D ZB Featuring Nickel Base and Gold Plated Contact Terminal
USB-Micro B Receptacle Connector Through Hole
Durable hanxia HX 10.0 180 ZCZB USB connector rated DC 30V 1.5A for industrial applications
USB-A (USB TYPE-A) Receptacle Connector 4 Position Through Hole
USB component hanxia HX 10.0 HCHTZB6.3 tested for connection force and performance in pressure range 86 to 106 Kpa
SMD USB, DVI, HDMI Connector Assemblies RoHS
USB connector hanxia HX AF 90 ZJDG JB offering robust connection and insulation resistance properties
Through Hole USB, DVI, HDMI Connector Assemblies RoHS
HX MICRO 7.2 JBWZ Micro USB connector offering low contact resistance and high insulation resistance
USB-Micro B Receptacle Connector Surface Mount, Right Angle
Durable hanxia HX MICRO 2PCB1.6 ZB Micro USB connector with tested mechanical and electrical specifications
USB-Micro B Receptacle Connector Recessed Mount
Micro USB Connector Hanxia HX MICRO 4PCB1.0 JB with C5191 Nickel Base and Gold Plated Contact Terminal
USB-Micro B Receptacle Connector Recessed Mount
Micro USB Connector Hanxia HX MICRO DNJ JB with Durable Plastic and Gold Plated Contact Terminals
USB-Micro B Receptacle Connector Surface Mount, Right Angle
Electrical connector hanxia HX AM 90D with plated gold contacts in mating area and tin on solder tails
USB-A (USB TYPE-A) Receptacle Connector 4 Position Through Hole
Micro USB hanxia HX 10.0 4JCHT6.3 product specification with temperature humidity and pressure tolerance
USB-A (USB TYPE-A) Receptacle Connector 4 Position Surface Mount, Right Angle
Send RFQ
Stock:
MOQ:
